2 layers103.9 × 119.3 mm
Prototype test
DIaLOGIKa-GmbH/modular-nerf-target
A hex-based modular system to build custom nerf gun targets
69 parts1MIT
2 layers223.8 × 240.4 mm
Nerf target v1 panel
DIaLOGIKa-GmbH/modular-nerf-target1A hex-based modular system to build custom nerf gun targets
- Size
- 223.8 × 240.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 346
- Nets
- 232
- Pads
- 878
- Tracks, vias
- 1,372, 168
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 6 Apr 2024
- Updated
- 21 Jun 2024
Overview
Nerf target v1 panel is an open-source printed circuit board by DIaLOGIKa-GmbH, from the DIaLOGIKa-GmbH/modular-nerf-target repository on GitHub, published under the MIT licence. It is a 2-layer board of 223.8 × 240.4 mm with 346 parts on 232 nets, routed with 1,372 tracks and 168 vias.
It is built around the RP2040, W25Q128JVSIQ and M24C02-WMN6, with the S8050 and X322512MSB4SI among its other parts. Its parts include 72 capacitors, 68 resistors, 52 connectors, 36 diodes and 12 ICs. It belongs with the RP2040 boards of this library.
Main components
5
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
M24C02-WMN6
SO-8SO-8 EEPROM ROHSSTMicroelectronicsEEPROM
S8050
SOT-23-55℃~+150℃ 1 NPN 100MHz 100nA 120 25V 300mW 500mA 5V 600mV NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
X322512MSB4SI
SMD3225-4P-40℃~+85℃ 12MHz 20pF 80Ω Crystal Oscillator ±10ppm ±20ppm SMD3225-4P Crystals ROHSYXCCrystals
README
README.mdNodular Nerf Target
A hex-based modular system to build custom nerf gun targets
Parts
346| Qty | Value | Footprint | References |
|---|---|---|---|
| 80 | NPTH | NPTH | KiKit_MB_10_2, KiKit_MB_10_3, KiKit_MB_10_4, KiKit_MB_11_1, KiKit_MB_11_2, KiKit_MB_11_3, KiKit_MB_11_4, KiKit_MB_12_1, KiKit_MB_12_2, KiKit_MB_12_3, KiKit_MB_12_4, KiKit_MB_13_1, KiKit_MB_13_2, KiKit_MB_13_3, KiKit_MB_13_4, KiKit_MB_14_1 +64 |
| 48 | SolderPad | #TimGollLib:solder_pad_1.2x2.5mm | J1, J1, J1, J1, J10, J10, J10, J10, J11, J11, J11, J11, J12, J12, J12, J12 +32 |
| 44 | 100n | Capacitor_SMD:C_0402_1005Metric | C2, C2, C2, C2, C10, C10, C10, C10, C13, C13, C13, C13, C20, C20, C20, C20 +28 |
| 24 | 220 | Resistor_SMD:R_0402_1005Metric | R2, R2, R2, R2, R3, R3, R3, R3, R5, R5, R5, R5, R10, R10, R10, R10 +8 |
| 12 | 120 | Resistor_SMD:R_0402_1005Metric | R4, R4, R4, R4, R8, R8, R8, R8, R11, R11, R11, R11 |
| 12 | 2u2 | Capacitor_SMD:C_0603_1608Metric | C1, C1, C1, C1, C11, C11, C11, C11, C21, C21, C21, C21 |
| 12 | blue | LED_SMD:LED_0603_1608Metric | D3, D3, D3, D3, D6, D6, D6, D6, D9, D9, D9, D9 |
| 12 | green | LED_SMD:LED_0603_1608Metric | D2, D2, D2, D2, D5, D5, D5, D5, D8, D8, D8, D8 |
| 12 | red | LED_SMD:LED_0603_1608Metric | D1, D1, D1, D1, D4, D4, D4, D4, D7, D7, D7, D7 |
| 8 | 2k2 | Resistor_SMD:R_0402_1005Metric | R7, R7, R7, R7, R15, R15, R15, R15 |
| 8 | 33p | Capacitor_SMD:C_0402_1005Metric | C14, C14, C14, C14, C15, C15, C15, C15 |
| 8 | 4k7 | Resistor_SMD:R_0603_1608Metric | R12, R12, R12, R12, R13, R13, R13, R13 |
| 8 | testpoint | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP1, TP1, TP1, TP2, TP2, TP2, TP2 |
| 6 | Fiducial | Fiducial | KiKit_FID_B_1, KiKit_FID_B_2, KiKit_FID_B_3, KiKit_FID_T_1, KiKit_FID_T_2, KiKit_FID_T_3 |
| 4 | 100k | Resistor_SMD:R_0603_1608Metric | R16, R16, R16, R16 |
| 4 | 10u | Capacitor_SMD:C_0805_2012Metric | C16, C16, C16, C16 |
| 4 | 1n | Capacitor_SMD:C_0805_2012Metric | C17, C17, C17, C17 |
| 4 | 20k | Resistor_SMD:R_0603_1608Metric | R18, R18, R18, R18 |
| 4 | 470 | Resistor_SMD:R_0402_1005Metric | R14, R14, R14, R14 |
| 4 | 82k | Resistor_SMD:R_0603_1608Metric | R17, R17, R17, R17 |
| 4 | CortexDebug10 | #TimGollLib:FTSH-105-01-F-DV-K | J3, J3, J3, J3 |
| 4 | Goertek B4013AM422-42 | #TimGollLib:B4013AM422-42 | MK1, MK1, MK1, MK1 |
| 4 | M24C02-WMN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5, U5, U5, U5 |
| 4 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U2, U2, U2, U2 |
| 4 | S8050 | Package_TO_SOT_SMD:SOT-23 | Q1, Q1, Q1, Q1 |
| 4 | W25Q128JVS | Package_SO:SOIC-8_5.275x5.275mm_P1.27mm | U1, U1, U1, U1 |
| 4 | X322512MSB4SI | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1, Y1, Y1, Y1 |
More from DIaLOGIKa-GmbH/modular-nerf-target
3- 2 layers103.9 × 119.3 mm
Nerf target v1
DIaLOGIKa-GmbH/modular-nerf-target
A hex-based modular system to build custom nerf gun targets
65 parts1MIT - 2 layers35.6 × 22.9 mm
Amplifier test
DIaLOGIKa-GmbH/modular-nerf-target
A hex-based modular system to build custom nerf gun targets
10 parts1MIT
Similar boards
- 2 layers99.1 × 99 mm
XDuinoRail Debug
chatelao/xDuinoRail-Decoder
The friendly decoder development plattform for model railroad tinkers.
170 partsAGPL-3.0 - 4 layers80 × 99 mm
- 6 layers73 × 75.5 mm
Tc2-main pcb
TheCacophonyProject/thermal-camera-v2
tc2-panel.py uses KiKit to build the manufacturing panel from the individual board files.
219 partsCERN-OHL-W-2.0 - 2 layers
Bias controller
loxodes/vna
Under development open hardware microwave vector network analyzer
203 parts205 - 2 layers
8-ball badge
tylercrumpton/magic-8-badge
An Open Source CircuitPython-compatible PCB badge that can (maybe) tell the future!
90 parts2 - 4 layers72.6 × 170 mm
OpenJBOD RP2040
OpenJBOD/rp2040
This repository contains the hardware design files OpenJBOD RP2040 Baseboard.
129 parts87CERN-OHL-P-2.0 - 2 layers65 × 45 mm
- 4 layers142 × 119.7 mm
Questions
How big is the Nerf target v1 panel PCB?
It measures 223.8 × 240.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Nerf target v1 panel use?
346 parts, built around the RP2040, W25Q128JVSIQ, M24C02-WMN6 and S8050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Nerf target v1 panel KiCad files?
From the DIaLOGIKa-GmbH/modular-nerf-target repository on GitHub, at the commit this page was made from: the board is electronics/nerf-target-v1_panel/nerf-target-v1_panel.kicad_pcb and its schematic electronics/amplifier-sim/amplifier-sim.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Nerf target v1 panel design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).