Skip to the content
2 layers22.3 × 17.8 mmWaterFlowMeter, the printed circuit board in 3D
Size
22.3 × 17.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
43
Nets
60
Pads
193
Tracks, vias
325, 179
Pours
3
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
31 Jul 2024
Updated
5 Aug 2024

Overview

WaterFlowMeter is an open-source printed circuit board by Circuit-Digest, from the Circuit-Digest/IoT-Water-Flow-Meter repository on GitHub. It is a 2-layer board of 22.3 × 17.8 mm with 43 parts on 60 nets, routed with 325 tracks and 179 vias.

It is built around the ESP32-S3-WROOM-1-N8, AO3401A and ADM803SAKSZ-REEL7, with the ADP1706ARDZ-3.3-R7, B2B-PH-SM4-TB(LF)(SN) and S8050 among its other parts. Its parts include 14 resistors, 9 capacitors, 6 ICs, 5 connectors and 3 diodes. It belongs with the ESP32 boards of this library.

Main components

7

README

README.md

DIY ESP32-Based Water Flow Meter: Conserve Water, Save the Planet

Water Flow Meter Water is one of our most precious resources, vital for all forms of life on Earth. Despite its importance, water wastage is a significant issue globally, contributing to water scarcity and environmental degradation. Efficient water management is crucial in addressing this challenge, and technology plays a vital role in it. By monitoring and managing water usage, we can significantly reduce wastage. As a first step in addressing this, we have designed an IoT based water flow meter. It is powered by the ESP32-S3 SoC from Espressif. We have used an ESP32-S3 Wroom 1 module for the project which will be much easier to handle when assembling the PCB. the device itself is battery powered and the custom PCB contains the necessary battery charging circuitry to recharge the internal battery. The battery charging circuit is based on the MAX1898 single-cell battery charger chip from Analog Devices. For powering the ESP32-S3 we have used the ADP1706 ultra low noise LDO, and for the reset circuitry we have used the ADM803 power supervisory chip. We have also included a provision for a 1.28” round TFT display for any future upgrades. The flow meter can be directly attached to the top of the flow sensor.

Parts

43
QtyValueFootprintReferences
4100KResistor_SMD:R_0603_1608MetricR10, R11, R13, R14
410uFCapacitor_SMD:C_0603_1608MetricC3, C5, C8, C9
30.1uFCapacitor_SMD:C_0603_1608MetricC1, C2, C7
310KResistor_SMD:R_0603_1608MetricR1, R3, R4
21uFCapacitor_SMD:C_0603_1608MetricC4, C6
233RResistor_SMD:R_0603_1608MetricR5, R6
25K1Resistor_SMD:R_0603_1608MetricR7, R8
2AO3401APackage_TO_SOT_SMD:SOT-23U1, U5
2Conn_01x03Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_VerticalJ2, J4
2LOGOLOGOG***, G***
1 B2B-PH-SM4-TB(LF)(SN) Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalJ3
11.4KResistor_SMD:R_0603_1608MetricR12
110Resistor_SMD:R_0603_1608MetricR2
11KResistor_SMD:R_0603_1608MetricR9
1ADM803SAKSZ-REEL7ADM803SAKSZ:KS_3_ADIU8
1ADP1706ARDZ-3.3-R7ADP1706ARDZ:SOIC127P600X175-9NIC2
1ESP32-S3-WROOM-1Espressif:ESP32-S3-WROOM-1U2
1GC9A01GC9A01:GC9A01J5
1LED BlueLED_SMD:LED_0603_1608MetricLED4
1LED RedLED_SMD:LED_0603_1608MetricLED1
1MAX1898EUB42+TMAX1898EUB42:SOP50P490X110-10NIC3
1RESET3x4x2:Tactile 3x4x2mm TS-A010BOOT2
1S8050Package_TO_SOT_SMD:SOT-23Q1
1SLW-66527511-SMT-TRSMD_Slide_switch:slide switch spdtSW1
1SS14DDiode_SMD:D_SMAD2
1UBOOT3x4x2:Tactile 3x4x2mm TS-A010BOOT1
1USB_C_Receptacle_USB2.0Connector_USB:USB_C_Receptacle_XKB_U262-16XN-4BVC11J1

Similar boards

  • 2 layers25.7 × 14.6 mmGesture Recognition, the printed circuit board in 3D

    Gesture Recognition

    Circuit-Digest/Gesture-recognition-APDS9500

    Gesture recognition module using APDS9500

    55 parts
  • 2 layers105 × 90 mmLow Power Desktop Weather Station, the printed circuit board in 3D

    Low Power Desktop Weather Station

    jobitjoseph/Desktop-Weather-Station

    This project offers a practical way to build a clean and minimal weather station using an ESP32 microcontroller and an E-Ink display.

    65 parts4
  • 2 layers80 × 50 mmThermal Camera, the printed circuit board in 3D

    Thermal Camera

    Circuit-Digest/MLX90640-Thermal-Camera

    An Open Source Thermal Imaging IR camera that you can build yourserlf

    66 parts94
  • 2 layers90 × 60 mmSchem, the printed circuit board in 3D

    Schem

    Abhey-05/Thermal-Camera

    Thermal Camera A compact, low-cost thermal imaging solution built for diagnostic, repair, and monitoring applications in electronics, industrial safety, and embedded systems.

    60 parts
  • 2 layers53.1 × 100.5 mmJammer, the printed circuit board in 3D

    Jammer

    aryakaithal8/Jammer

    A jamming device which jam everything

    94 parts
  • 2 layersAI voice assistant, the printed circuit board in 3D

    AI voice assistant

    DhamuVkl/ESP32S3-AI-Voice-Assistant

    This project is a complete DIY AI voice assistant built around the ESP32-S3 microcontroller. It combines custom PCB design, advanced audio processing, and cloud-based AI to create a device that rivals commercial smart…

    78 parts26MIT
  • 2 layers45.2 × 65 mmPrecision Digital Micro Current Meter, the printed circuit board in 3D

    Precision Digital Micro Current Meter

    jobitjoseph/Precision-Digital-Micro-Current-Meter

    Keeping track of extremely low current levels is often essential when developing or testing low-power devices, especially in the field of embedded systems and battery-operated electronics.

    67 parts7

Questions

How big is the WaterFlowMeter PCB?

It measures 22.3 × 17.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the WaterFlowMeter use?

43 parts, built around the ESP32-S3-WROOM-1-N8, AO3401A, ADM803SAKSZ-REEL7 and ADP1706ARDZ-3.3-R7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the WaterFlowMeter KiCad files?

From the Circuit-Digest/IoT-Water-Flow-Meter repository on GitHub, at the commit this page was made from: the board is PCB/WaterFlowMeter/WaterFlowMeter.kicad_pcb and its schematic PCB/WaterFlowMeter/WaterFlowMeter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the WaterFlowMeter design in my own project?

Its repository states no licence, so its author keeps all rights: ask Circuit-Digest before reusing the design.