

IEE Drone 2026
Drone project for IEEE 2026 UAV. Primarily created by Caleb Murray
- Size
- 41.6 × 42 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 54
- Nets
- 80
- Pads
- 248
- Tracks, vias
- 610, 108
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 31 Aug 2025
- Updated
- 5 Jan 2026
Overview
IEE Drone 2026 is an open-source printed circuit board by CalebJM04, from the CalebJM04/IEEE-2026-UAV repository on GitHub. It is a 4-layer board of 41.6 × 42 mm with 54 parts on 80 nets, routed with 610 tracks and 108 vias.
It is built around the BMP390, LIS2MDL and TPSM84209RKHT, with the ABMM2-32.768MHZ-E2F-T and ICM-42605 among its other parts. Its parts include 20 capacitors, 11 resistors, 5 connectors, 4 ICs and 2 diodes. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
5BMP390
LGA-10(2x2)-40℃~+85℃ 0.6pa/K 1.5uA 1.65V~3.6V 30Kpa~1.25bar 3pa 50pa I2C、SPI Integrated ADC and digital interface、Standby mode、On-chip temperature output Yes LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure SensorsLIS2MDL
LGA-12(2x2)-40℃~+85℃ 1.71V~3.6V 16bit 200uA I2C、SPI ±5mT ±5mT LGA-12(2x2) 3D Magnetic Sensors ROHSSTMicroelectronics3D Magnetic SensorsTPSM84209RKHT
QFN-9(4x4.4)-40℃~+85℃ 1 1.2V~6V 2.5A 4.5V~28V 750kHz Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Hiccup current limiting Step-down type QFN-9(4x4.4) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersABMM2-32.768MHZ-E2F-T
SMD6036-4P-20℃~+70℃ 18pF 32.768MHz 50Ω ±20ppm ±20ppm SMD6036-4P Crystals ROHSAbraconCrystalsICM-42605
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 2KB 7.5uA IMU (accelerometer + gyroscope) Motion event detection SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSTDK InvenSenseAccelerometers
README
README.mdThis is a custom UAV PCB designed for competition at the 2026 IEEE Robotics and Automation Conference at UAH.
*PCB Stackup
This board was custom-designed by me. It features two linear regulators to power an RFM9x feather (which this PCB will support as the main microcontroller), a barometer for accurate altitude data, and pinouts for ESC PWM support, as well as pinouts for a Pixy2 camera for image recognition.
*PCB 3d view
Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C10, C11, C15, C16, C17, C18, C22 |
| 8 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R5, R7, R9, R10, R11 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | 3V3, GND, NRST, SWCLK, SWDIO |
| 4 | M4 Mounting | Mounting:MountingHole_4.3mm_M4 | J2, J3, J4, J5 |
| 3 | 2.2uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13, C20, C21 |
| 2 | 12pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C8 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R8 |
| 2 | D_Schottky | schottky:DIODE_DO214AC | D1, D2 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C14 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 1 | 2.2k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | 220nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12 |
| 1 | 330pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C19 |
| 1 | 47uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C4 |
| 1 | ABMM2-32.768MHZ-E2F-T | bmp390:ABMM2 | Y2 |
| 1 | BMP390 | bmp390:10LGA_2X2X0p75_BOS | U3 |
| 1 | Conn_01x04_Socket | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | SWD |
| 1 | ESC | Connector_JST:JST_SHL_SM08B-SHLS-TF_1x08-1MP_P1.00mm_Horizontal | ESC |
| 1 | GPS | Connector_JST:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | GPS |
| 1 | ICM-42605 | forICM:XDCR_ICM-42605 | MT1 |
| 1 | LIS2MDL | Package_LGA:LGA-12_2x2mm_P0.5mm | U5 |
| 1 | Pixy2 | Connector_JST:JST_SH_BM05B-SRSS-TB_1x05-1MP_P1.00mm_Vertical | Pixy |
| 1 | RF | Connector_JST:JST_SH_BM09B-SRSS-TB_1x09-1MP_P1.00mm_Vertical | RF |
| 1 | STM32F405RGTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | TPSM84209RKHT | KiCad:TPSM84209RKHT | IC1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J13 |
Similar boards
- 2 layers57.2 × 101.6 mm

- 2 layers41 × 42 mm

Mini Air FC
darshg321/Mini-Air
Mini-Air is a DIY FPV drone! it features: - a custom flight controller supporting Betaflight - an ESC supporting Bluejay firmware - ELRS protocol - an analog camera - GPS
101 parts2CERN-OHL-W-2.0 - 4 layers29.7 × 29.7 mm

- 4 layers112.7 × 122 mm

- 2 layers91.5 × 100 mm

Trailmap
katetriestocode/trailmap
this is the working version! (disclaimer: no antenna as it has not delivered yet, so manual gps coords insertion for now!)
57 parts2 - 4 layers55 × 140 mm

- 6 layers30 × 60 mm

LSR FLCM0001 A03
Louisiana-State-Rocketry/FLCM0001-A03_PCB
PCB Files for the Eclipse 2 Flight Computer.
150 partsMIT - 4 layers65 × 64.6 mm

Questions
How big is the IEE Drone 2026 PCB?
It measures 41.6 × 42 mm and has 4 copper layers, 1.6 mm thick.
What parts does the IEE Drone 2026 use?
54 parts, built around the BMP390, LIS2MDL, TPSM84209RKHT and ABMM2-32.768MHZ-E2F-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the IEE Drone 2026 KiCad files?
From the CalebJM04/IEEE-2026-UAV repository on GitHub, at the commit this page was made from: the board is IEEE_Drone_2026/IEE_Drone_2026.kicad_pcb and its schematic IEEE_Drone_2026/IEE_Drone_2026.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the IEE Drone 2026 design in my own project?
Its repository states no licence, so its author keeps all rights: ask CalebJM04 before reusing the design.