
Mutant SMD
soggybag/Mutant-SMD
A redesign of the Mutant generative synth (MeeBleeps, https://github.com/Meebleeps/MeeBleeps-Mutant-Synth), based on the Eurorack version in /Documents/Arduino/projects/MutantGenerativeArduinoSynth/ (Instructables…

Multi-Effect Guitar Pedal Code for Daisy Seed + PCB & Schematic Design
Daisy MultiEffect Pedal is an open-source printed circuit board by AryamaanDash, from the AryamaanDash/MultiEffectPedal repository on GitHub. It is a 2-layer board of 150 × 90 mm with 24 parts on 20 nets, routed with 93 tracks and 0 vias.
It is built around the MCP6002-I/P and B10K. Its parts include 7 capacitors, 7 resistors, 2 ICs, 2 connectors and 1 switch. It belongs with the audio and music boards of this library.
Multi-effect guitar pedal firmware and a custom KiCad PCB for the Daisy Seed. The firmware runs distortion, stereo reverb, delay, and flanger effects at the Daisy audio sample rate, with a footswitch for cycling through the effects.
src/main.cpp Hardware composition and application entry point
src/AudioEngine.cpp Real-time block processing and output limiting
src/EffectManager.cpp Effect ownership-independent routing and mode changes
src/PedalControls.cpp Foreground switch scanning and LED state
src/effects/ Individual DSP effect adapters
include/ Public interfaces and shared audio typesEvery effect implements the EffectProcessor interface:
virtual void Init(float sample_rate) = 0;
virtual void SetParameters(const EffectParameters& parameters) = 0;
virtual StereoFrame Process(float input) = 0;Effect parameters use normalized values from 0 to 1. Each adapter maps those values to the range expected by its DaisySP processor. Mode changes are sent from the foreground loop through an atomic request and applied by the audio engine at the next block boundary.
The reverb and one-second delay buffers remain in external SDRAM. Effect objects and the manager are statically allocated; audio processing performs no dynamic allocation.
This project expects libDaisy and DaisySP to be available at the paths in
the Makefile.
makeTo add an effect, implement EffectProcessor, register the instance with
EffectManager, and add its source file to CPP_SOURCES in the Makefile.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | B10K | Custom:Pot_3Pin_B10K_Wired | RV1, RV2, RV3, RV4 |
| 1 | 100R | Custom:TH_2Pin_7p62 | R4 |
| 1 | 100R out iso | Custom:TH_2Pin_7p62 | R6 |
| 1 | 100k VREF bottom | Custom:TH_2Pin_7p62 | R2 |
| 1 | 100k VREF top | Custom:TH_2Pin_7p62 | R1 |
| 1 | 100k out bias | Custom:TH_2Pin_7p62 | R5 |
| 1 | 100k output pulldown | Custom:TH_2Pin_7p62 | R7 |
| 1 | 100nF MCP6002 decouple | Custom:TH_2Pin_7p62 | C3 |
| 1 | 100nF VREF | Custom:TH_2Pin_7p62 | C2 |
| 1 | 10uF VREF | Custom:TH_2Pin_7p62 | C1 |
| 1 | 10uF output coupling | Custom:TH_2Pin_7p62 | C7 |
| 1 | 1M input bias | Custom:TH_2Pin_7p62 | R3 |
| 1 | 1uF from Daisy Out | Custom:TH_2Pin_7p62 | C6 |
| 1 | 1uF input coupling | Custom:TH_2Pin_7p62 | C4 |
| 1 | 1uF to Daisy In | Custom:TH_2Pin_7p62 | C5 |
| 1 | B10K volume | Custom:Pot_3Pin_B10K_Wired | RV5 |
| 1 | Daisy Seed socket / 2x20 | Custom:Daisy_Seed_2x20_Socket | U2 |
| 1 | INPUT_TS_JACK | Custom:Jack_or_Switch_2Pin | J1 |
| 1 | MCP6002-I/P | Package_DIP:DIP-8_W7.62mm | U1 |
| 1 | MOMENTARY_MODE_SWITCH | Custom:Jack_or_Switch_2Pin | SW1 |
| 1 | OUTPUT_TS_JACK | Custom:Jack_or_Switch_2Pin | J2 |

soggybag/Mutant-SMD
A redesign of the Mutant generative synth (MeeBleeps, https://github.com/Meebleeps/MeeBleeps-Mutant-Synth), based on the Eurorack version in /Documents/Arduino/projects/MutantGenerativeArduinoSynth/ (Instructables…



GaudiLabs/OpenLaserScanningMicroscope
Open Source Laser Scanning Microscope


GuitarML/GuitarPedalSTM32
Guitar pedal using a stm32h7 microcontroller programmed with CubeIDE (PCB and Firmware)

thawney/PedalPiV2
Pedal Pi V2 by Thawney is an all new and regularly maintained Pedal-Pi by electrosmash; a lo-fi programmable guitar pedal that works with the Raspberry Pi ZERO Board.

CCHS-Melbourne/ESPlant
Environmental Sensor Plant - solar WiFi gardening/meteorological sensor using ESP8266
It measures 150 × 90 mm and has 2 copper layers, 1.6 mm thick.
24 parts, built around the MCP6002-I/P and B10K. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the AryamaanDash/MultiEffectPedal repository on GitHub, at the commit this page was made from: the board is Daisy_MultiEffect_Pedal_KiCad_Starter/Daisy_MultiEffect_Pedal.kicad_pcb and its schematic Daisy_MultiEffect_Pedal_KiCad_Starter/Daisy_MultiEffect_Pedal.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask AryamaanDash before reusing the design.