

Proyecto Bioimpedancia
- Size
- 61.1 × 35.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 34
- Pads
- 175
- Tracks, vias
- 539, 51
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 4 May 2017
- Updated
- 2 Oct 2017
Overview
Proyecto Bioimpedancia is an open-source printed circuit board by AndreSuarez, from the AndreSuarez/Bioimpedanciometro_PCB repository on GitHub. It is a 2-layer board of 61.1 × 35.4 mm with 57 parts on 34 nets, routed with 539 tracks and 51 vias.
It is built around the ATMEGA328P-AU, AD8606ARZ and ADP3334AR. Its parts include 16 capacitors, 15 resistors, 11 connectors, 5 ICs and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)AD8606ARZ
SOIC-8-40℃~+125℃ 0.5pA 1.2mA 100dB 10MHz 1pA 2 2.7V~5.5V 4.5uV/℃ 5V/us 80mA 80uV 8nV/√Hz@1kHz ESD protection、Built-in compensation、Overvoltage protection、Reverse-phase input protection Rail-to-Rail Input, Rail-to-Rail Output SOIC-8 Precision Op Amps ROHSAnalog DevicesPrecision Op AmpsADP3334AR
SOIC-8-40℃~+85℃@(Ta) 1 1.5V~10V 11V 200mV@(500mA) 27uVrms 500mA 90uA Adjustable Over Current Protection、Thermal shutdown、Enable control Positive SOIC-8 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAnalog DevicesVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdPruba
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0,1uF | Capacitors_SMD:C_0805_HandSoldering | C3, C4, C5, C6, C7, C13 |
| 6 | CONN_01X02 | Socket_Strips:Socket_Strip_Straight_1x02_Pitch2.54mm | P2, P3, P4, P5, P6, P7 |
| 6 | TEST_1P | Measurement_Points:Measurement_Point_Round-TH_Small | W1, W2, W3, W4, W5, W6 |
| 4 | 10K | Resistors_SMD:R_0805_HandSoldering | R3, R4, R11, R13 |
| 4 | 50K | Resistors_SMD:R_0805_HandSoldering | R1, R2, R5, R6 |
| 3 | Jumper | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J2, J3, J4 |
| 2 | 10uF | Capacitors_SMD:C_0805_HandSoldering | C2, C17 |
| 2 | 18pF | Capacitors_SMD:C_0805_HandSoldering | C8, C9 |
| 2 | 1uF | Capacitors_SMD:C_0805_HandSoldering | C10, C11 |
| 2 | 20K | Resistors_SMD:R_0805_HandSoldering | R8, R9 |
| 1 | 0,01uF | Capacitors_SMD:C_0805_HandSoldering | C12 |
| 1 | 140K | Resistors_SMD:R_0805_HandSoldering | R15 |
| 1 | 1K | Resistors_SMD:R_0805_HandSoldering | R12 |
| 1 | 1nF | Capacitors_SMD:C_1206_HandSoldering | C14 |
| 1 | 20pF | Capacitors_SMD:C_0805_HandSoldering | C20 |
| 1 | 47nF | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | 78,7K | Resistors_SMD:R_0805_HandSoldering | R14 |
| 1 | AD5933 | Housings_SSOP:SSOP-16_5.3x6.2mm_Pitch0.65mm | BIO1 |
| 1 | AD8606 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U1 |
| 1 | ADG819 | Housings_SSOP:MSOP-8_3x3mm_Pitch0.65mm | U2 |
| 1 | ADP3334 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U5 |
| 1 | AMB3_16M | Crystals:Crystal_SMD_Abracon_ABM3-2pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | Atmega328PA | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | U3 |
| 1 | CONN_01X03 | Socket_Strips:Socket_Strip_Straight_1x03_Pitch2.54mm | P1 |
| 1 | Jumper_Calibration | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J1 |
| 1 | KC5032A_CM | Huellas:KC5032A_CM | U4 |
| 1 | Led_Small_Reg | LEDs:LED_0805 | D2 |
| 1 | RCAL | Resistors_SMD:R_0805_HandSoldering | R10 |
| 1 | R_GAIN | Resistors_SMD:R_0805_HandSoldering | R7 |
| 1 | SW_PUSH | Huellas:KPT_1187B | SW1 |
More from AndreSuarez/Bioimpedanciometro_PCB
1- 2 layers63.5 × 34.3 mm

Similar boards
- 2 layers100 × 100 mm

- 4 layers99 × 99 mm

TOFE VGA
timvideos/HDMI2USB-TOFE-VGA
A VGA capture board for use with TOFE-8x compatible boards like the Numato Opsis.
141 parts9 - 2 layers94.4 × 37.1 mm

- 2 layers100 × 100 mm

BIO Respaldo
AndreSuarez/Bio_MicroMain_PCB-1
Diseño Final para la placa del Bioimpedanciometro
69 parts - 4 layers25.4 × 25.4 mm

Twonkie
dojoe/Twonkie
A USB-PD sniffer/injector/sink based on Google's Twinkie, re-designed to be manufactured by mere mortals.
62 parts415 - 2 layers41 × 22 mm

UECG rev4
ultimaterobotics/uECG_v4_3_all
uECG - very small wearable ECG device that sends raw and processed data over BLE
69 parts77MIT - 4 layers100 × 100 mm

All boards
ChicoLiebl/pressure-acquisition-system
Pressure acquisition system for a piezoelectric sensor
154 parts1 - 2 layers

Banyu done1 pcb
Adji-SP/Matlab_Dashboard
The Banyu40kWiredSchematic.zip package is schematic-only. No PCB is needed to open it. The old unrouted PCB remains in the workspace as an earlier artifact; the PCB discussion below refers to that earlier version.
135 parts
Questions
How big is the Proyecto Bioimpedancia PCB?
It measures 61.1 × 35.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Proyecto Bioimpedancia use?
57 parts, built around the ATMEGA328P-AU, AD8606ARZ and ADP3334AR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Proyecto Bioimpedancia KiCad files?
From the AndreSuarez/Bioimpedanciometro_PCB repository on GitHub, at the commit this page was made from: the board is Proyecto_Bioimpedancia/Proyecto_Bioimpedancia.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Proyecto Bioimpedancia design in my own project?
Its repository states no licence, so its author keeps all rights: ask AndreSuarez before reusing the design.