

MotionRecognitionWatch
A wristband-mounted gesture recognition system built around an STM32F411, IMU, and OLED display, with USB-C battery charging and ESD-protected I/O. Includes full PCB design, manufacturing files, and firmware for real-time motion capture and on-device gesture classification via TFLite Micro.
- Size
- 27.6 × 30.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 58
- Pads
- 213
- Tracks, vias
- 410, 35
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 18 Jul 2026
- Updated
- 18 Jul 2026
Overview
MotionRecognitionWatch is an open-source printed circuit board by AidenBTTU, from the AidenBTTU/Gesture-Capture-Watch repository on GitHub. It is a 2-layer board of 27.6 × 30.5 mm with 46 parts on 58 nets, routed with 410 tracks and 35 vias.
It is built around the STM32F411CEU6, BQ24092DGQR and LSM6DSOX, with the TPS7A0533PDBZ and USBLC6-2SC6 among its other parts. Its parts include 17 capacitors, 10 resistors, 5 ICs, 4 connectors and 1 diode. It belongs with the lEDs and displays boards and the STM32 boards of this library.
Main components
5STM32F411CEU6
UFQFPN-48(7x7)-40℃~+85℃ 1.7V~3.6V 100MHz 128KB 12bit 32 Bit 36 512KB ARM Cortex-M4 Built-in FLASH UFQFPN-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)BQ24092DGQR
MSOP-10-EP0℃~+125℃ 1 1.4A 125uA 4.2V 4.45V~6.45V Charging IC Lithium Battery Support MSOP-10-EP Battery Management ROHSTexas InstrumentsBattery ManagementLSM6DSOX
LGA-146-Axis IMU (Inertial Measurement Unit) with Embedded AI: Always-On 3-Axis Accelerometer and 3-Axis GyroscopeSTMicroelectronicsAccelerometersTPS7A0533PDBZ
SOT-23-3-40℃~+125℃@(Tj) 1 180uVrms 200mA 235mV@(200mA) 3.3V 3uA 40dB@(1kHz) 5.5V Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
README
README.mdGesture-Capture-Watch
A wristband-mounted gesture recognition system built around an STM32F411, IMU, and OLED display, with USB-C battery charging and ESD-protected I/O. Includes full PCB design, manufacturing files, and firmware for real-time motion capture and on-device gesture classification via TFLite Micro.
Hardware Overview
- MCU: STM32F411CEU6, high Flash and SRAM to run TFLite model
- IMU: LSM6DSOX, industry standard, small form factor, low power consumption, includes a machine learning core for pre-processing
- Power System:
- Interface: USB-C, flexible power delivery, industry standard
- ESD Protection: USBLC6-2SC6, industry standard
- Li-ion Battery Charger: BQ24092DGQR, short circuit protection, variable charging
- Linear Regulator: TPS7A0533PDBZ, low drop-out
- Display: 0.96" OLED display with SSD1306 chipset
Software Overview (WIP)
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C5, C6, C7, C12, C13, C14 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_2.0x2.0mm | 3V3, GND, SCL1, SCL2, SDA1 |
| 4 | 5.1k | Resistor_SMD:R_0402_1005Metric | R7, R8, R9, R10 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R4, R5, R6 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric | C3, C10, C11 |
| 3 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C1, C2, C17 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric | C15, C16 |
| 2 | 2k | Resistor_SMD:R_0402_1005Metric | R1, R3 |
| 2 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3, J4 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 120R | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | BQ24092DGQR | BQ24092DGQR:IC_XTR111AIDGQR | U5 |
| 1 | Conn_01x02_Socket | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LSM6DSOX | LSM6DSOX:PQFN50P250X300X86-14N | U6 |
| 1 | STM32F411CEU6 | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U3 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | ON |
| 1 | TPS7A0533PDBZ | Package_TO_SOT_SMD:SOT-23 | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J5 |
| 1 | ~ | TestPoint:TestPoint_Pad_2.0x2.0mm | SDA2 |
Similar boards
- 2 layers30 × 30 mm

- 2 layers26 × 38 mm

Li Charger
kbroomm/Single-Cell-Li-ion-Charger
KiCad PCB design for a single-cell lithium-ion battery charger, with a 5V USB-C input and 10-LED charge level indicator.
34 parts - 4 layers47.5 × 57 mm

- 2 layers69.9 × 78.7 mm

- 2 layers44.7 × 76.6 mm

ATSAME54N20A AU
Albinjm72/Microchip-ATSAME54-Development-Board
A fully custom development board built around the Microchip ATSAME54N20A-AU (ARM Cortex-M4F, 120MHz), designed end-to-end in KiCad — schematic, routing, and silkscreen.
45 partsCERN-OHL-S-2.0 - 4 layers157 × 105 mm

- 4 layers39.8 × 72.5 mm

NPulse v4
N-Pulse/ARM-ELEC-CTRL
Microcontroller : A STM32G484 optimized for mixed-signal applications with a 16MHz external oscillator. Control the 8 DC motors independently. Power Management : +12V supply +5V supplied from the Power Board.
163 partsCC-BY-4.0 - 4 layers88 × 35.8 mm

Questions
How big is the MotionRecognitionWatch PCB?
It measures 27.6 × 30.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the MotionRecognitionWatch use?
46 parts, built around the STM32F411CEU6, BQ24092DGQR, LSM6DSOX and TPS7A0533PDBZ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the MotionRecognitionWatch KiCad files?
From the AidenBTTU/Gesture-Capture-Watch repository on GitHub, at the commit this page was made from: the board is Hardware/MotionRecognitionWatch.kicad_pcb and its schematic Hardware/MotionRecognitionWatch.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the MotionRecognitionWatch design in my own project?
Its repository states no licence, so its author keeps all rights: ask AidenBTTU before reusing the design.