
Smart Vibration Sensor Circuit
AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

This repository contains various PCB design projects.
Positive Battery Charger Circuit is an open-source printed circuit board by AbhishekGM23, from the AbhishekGM23/PCB-Design repository on GitHub. It is a 2-layer board of 72 × 33 mm with 36 parts on 22 nets, routed with 181 tracks and 4 vias.
It is built around the NE555P, BC547 and BF494, with the IRF540N among its other parts. Its parts include 11 diodes, 8 resistors, 6 capacitors, 3 transistors and 3 connectors. It belongs with the power boards of this library.
This repository contains various PCB design projects.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 1N4007 | Diode_THT:D_DO-41_SOD81_P7.62mm_Horizontal | D1, D2, D3, D4, D5, D6, D7, D8 |
| 3 | 10A | Diode_THT:D_DO-201_P12.70mm_Horizontal | D9, D10, D11 |
| 2 | 10k | Potentiometer_THT:Potentiometer_ACP_CA6-H2,5_Horizontal | RV1, RV2 |
| 2 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R8 |
| 2 | 1uF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C4, C6 |
| 1 | 0.1uF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C3 |
| 1 | 100K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
| 1 | 100ohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 100uF/25V | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C2 |
| 1 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 12V Battery | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | J3 |
| 1 | 1nF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C1 |
| 1 | 1uF/400v | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C5 |
| 1 | 220K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7 |
| 1 | 240ohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6 |
| 1 | 33K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 6V Battery | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | J2 |
| 1 | BC547 | Package_TO_SOT_THT:TO-92_Inline | Q2 |
| 1 | BF494 | Package_TO_SOT_THT:TO-126-3_Vertical | Q1 |
| 1 | From Alternator Motor | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | J1 |
| 1 | IRF540N | Package_TO_SOT_THT:TO-220-3_Vertical | Q3 |
| 1 | LM396 | Package_TO_SOT_THT:TO-220-3_Vertical | U2 |
| 1 | NE555P | Package_DIP:DIP-8_W7.62mm | U1 |
| 1 | Transformer_1P_1S | Positive Battery Charger Circuit:Transformer_EI33 | T1 |

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.


AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

AbhishekGM23/PCB-Design
This repository contains various PCB design projects.

Junquilh0/FM-radio
While making this I saw a lot of different designs for similar radios. Mine is made of essentially two parts: ### The receiver - The coil (L) and the small variable capacitor (Cosc) choose which frequency the radio…

Lasthope027/Radio-station
This repository contains the design and simulation files for a 100 MHz FM transmitter, including the transmitter circuit, PCB design, manufacturing files, and a dedicated 100 MHz antenna design.


ambadran/Revolute_Joint
Optimal Cheap Robotic Actuator allowing high Torque and moderate Speed. Allow PRECISE Absolute, Speed and Torque Control. Using 3D-printed Cycloidal Drive, Custom PCB and LQR Control Algorithm.




404notfound-han/PCB-Awwaz
Sistem IoT kendali otomatisasi katup air Solenoid 12V berbasis ESP32. Desain PCB mandiri menggunakan driver internal MOSFET IRF540N horizontal, proteksi flyback diode 1N4007, dan sirkuit penurun tegangan step-down…
It measures 72 × 33 mm and has 2 copper layers, 1.6 mm thick.
36 parts, built around the NE555P, BC547, BF494 and IRF540N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the AbhishekGM23/PCB-Design repository on GitHub, at the commit this page was made from: the board is Basic circuits/Positive Battery Charger Circuit/Positive Battery Charger Circuit.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask AbhishekGM23 before reusing the design.