Skip to the content
12345

TPS62203DBV

Texas InstrumentsExtended

-40℃~+85℃@(TA) 1 15uA 1MHz 2.5V~6V 3.3V 300mA Buck Buck Built-in Fixed Yes SOT-23-5 DC-DC Converters ROHS

Part id
ti/TPS62203DBV
Category
DC DC Converters
Package
SOT-23-5
Pins
5
In stock
6,354 at JLCPCB (C9051)
Used on
17 open-source boards

Overview

The TPS62203DBV is a DC DC Converter made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+85℃@(TA) 1 15uA 1MHz 2.5V~6V 3.3V 300mA Buck Buck Built-in Fixed Yes SOT-23-5 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:TPS62203DBV, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 6,354 are in stock at JLCPCB (part C9051). 17 open-source boards in 16 repositories on GitHub use it.

Symbol

1VI2GND3EN4FB5SW
Regulator_Switching:TPS62203DBVFrom KiCad's library

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

14
Supply, least
2.5 V · VI, recommended operating minimum · p. 4
Supply, most
6 V · VI, recommended operating maximum · p. 4
Supply, absolute maximum
7 V · VI, absolute maximum · p. 3
Works up to
85 °C · Operating ambient temperature maximum · p. 4
Junction, hottest
150 °C · Operating junction temperature absolute maximum · p. 3
Takes working
15 µA · VI operating quiescent current typical, IO = 0 mA, device not switching · p. 5
Takes asleep
100 nA · Shutdown supply current typical, EN = GND · p. 5
Gives
300 mA · Output current maximum · p. 4
Current limit
480 mA · P-channel current limit typical, 2.5 V < Vin < 6.0 V · p. 5
Output
3.3 V · TPS62203 fixed output voltage nominal · p. 5
Switches at
1 MHz · Switching frequency typical · p. 5
Junction to air (DBV [SOT-23])
220 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DBV [SOT-23])
125 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (DBV [SOT-23])
36 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

6
Converter
High-efficiency synchronous step-down, up to 95% efficiency · p. 1
Power save mode
Highest efficiency over wide load current range · p. 1
Soft start
Internal soft start · p. 9
Low-dropout operation
100% duty cycle · p. 1
Output voltage control
Dynamic output-voltage positioning · p. 1
Package
5-pin SOT23 · p. 1

Around it

3
ind 10 µH
between SW and VOUT; Typical inductor value; choose low DC resistance and sufficient current rating to avoid saturation. · p. 12
cap 4.7 µF
between VI and GND; Low ESR input capacitor; ceramic performs well. Place as close as possible to the input pin. · p. 4
cap 10 µF
between VOUT and GND; Low ESR ceramic output capacitor recommended. · p. 13

Specifications

40
ParameterConditionsAs printedPage
Supply voltages (2) VIOver operating free-air temperature range; relative to network groundmin -0.3 · max 7 V3
Voltages on pins SW, EN, FB (2)Over operating free-air temperature range; maximum VCC +0.3 Vmin -0.3 V3
Operating junction temperature TJmin -40 · max 150 °C3
Storage temperature Tstgmin -65 · max 150 °C3
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1); ±2000 V ratingmax 2000 V3
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101 (2); ±500 V ratingmax 500 V3
Supply voltage VIOver operating free-air temperature rangemin 2.5 · max 6 V4
Output current IOmax 300 mA4
Inductor (1) LNominal value 10 uHmin 4.7 · typ 10 uH4
Input capacitor CINominal value; see Application and Implementationtyp 4.7 uF4
Output capacitor (1) CONominal valuetyp 10 uF4
Operating ambient temperature TAMinimum transcribed as printedmin 40 · max 85 °C4
Operating junction temperature TJMinimum transcribed as printedmin 40 · max 125 °C4
Junction-to-ambient thermal resistance RθJATPS6220x, DBV [SOT-23], 5 pinstyp 220 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)TPS6220x, DBV [SOT-23], 5 pinstyp 125 °C/W4
Junction-to-board thermal resistance RθJBTPS6220x, DBV [SOT-23], 5 pinstyp 36 °C/W4
Junction-to-top characterization parameter ψJTTPS6220x, DBV [SOT-23], 5 pinstyp 14 °C/W4
Junction-to-board characterization parameter ψJBTPS6220x, DBV [SOT-23], 5 pinstyp 35 °C/W4
Input voltage VImin 2.5 · max 6 V5
Operating quiescent current IQIO = 0 mA, Device is not switchingtyp 15 · max 30 uA5
Shutdown supply currentEN = GNDtyp 0.1 · max 1 uA5
Undervoltage lockout thresholdmin 1.5 · max 2 V5
EN high level input voltage V(EN)min 1.3 V5
EN low level input voltage V(EN)max 0.4 V5
EN input bias current I(EN)EN = GND or VINtyp 0.01 · max 0.1 uA5
P-channel MOSFET on-resistance rds(ON)VIN = VGS = 3.6 Vtyp 530 · max 690 mΩ5
P-channel MOSFET on-resistance rds(ON)VIN = VGS = 2.5 Vtyp 670 · max 850 mΩ5
N-channel MOSFET on-resistance rds(ON)VIN = VGS = 3.6 Vtyp 430 · max 540 mΩ5
N-channel MOSFET on-resistance rds(ON)VIN = VGS = 2.5 Vtyp 530 · max 660 mΩ5
P-channel leakage current Ilkg_(P)VDS = 6.0 Vtyp 0.1 · max 1 uA5
N-channel leakage current Ilkg_(N)VDS = 6.0 Vtyp 0.1 · max 1 uA5
P-channel current limit I(LIM)2.5 V < Vin < 6.0 Vmin 380 · typ 480 · max 670 mA5
Switching frequency fSmin 650 · typ 1000 · max 1500 kHz5
Reference voltage Vreftyp 0.5 V5
Fixed output voltage (1) VOTPS62203, 3.3 V nominal; VI = 3.6 V to 6 V, IO = 0 mA; relative errormin 0 · max 3 %5
Fixed output voltage (1) VOTPS62203, 3.3 V nominal; VI = 3.6 V to 6 V, 0 mA ≤ IO ≤ 300 mA; relative errormin -3 · max 3 %5
Line regulationVI = 2.5 V to 6 V, IO = 10 mAtyp 0.26 %/V5
Load regulationIO = 100 mA to 300 mAtyp 0.0014 %/mA5
Leakage current into SW pin IlkgVin > Vout, 0 V ≤ Vsw ≤ Vintyp 0.1 · max 1 uA5
Reverse leakage current into pin SW Ilkg(Rev)Vin = open, EN = GND, VSW = 6 Vtyp 0.1 · max 1 uA5

Pins, by the datasheet

5
1 VI
Supply voltage pin. · p. 3
2 GND
Ground. · p. 3
3 EN
Pull to ground for shutdown or to Vin to enable; must not float. · p. 3
4 FB
Feedback pin; connect directly to the output for this fixed output voltage version. · p. 3
5 SW
Connect the inductor here; switch pin connected to the internal MOSFET switches. · p. 3

Open-source boards using it

17See all 17
  • 4 layers45 × 32 mmTemplog mainboard, the printed circuit board in 3D

    Templog mainboard

    Michael-Manning/E-Paper-Climate-Logger

    Firmware, PCB, and enclosure for the Weathergotchi E-Paper climate logger.

    68 parts457MIT
  • 2 layers45 × 58.2 mmOpentama, the printed circuit board in 3D

    Opentama

    Sparkr-tech/opentama

    An open-source reference design for MCUGotchi

    65 parts237
  • 2 layers28 × 28 mmNikon gps, the printed circuit board in 3D

    Nikon gps

    4x1md/nikon_gps

    DIY GPS module for Nikon DSLR

    42 parts30MIT
  • 2 layers25.1 × 25.2 mmMini Environmental Sensor, the printed circuit board in 3D

    Mini Environmental Sensor

    MbFredys/PCB-Mini-Environmental-Sensor

    Compact ESP32-C3 environmental-sensor PCB design using BME280 and SGP40 for temperature, humidity, pressure, and VOC-based air-quality sensing.

    34 parts14
  • 2 layers60 × 80 mmGalaxy A5 dual node, the printed circuit board in 3D

    Galaxy A5 dual node

    DerRKDCB/meshphone

    meshtastic Samsung Galaxy A5 standalone offline dual node

    87 parts5
  • 4 layers36 × 36 mmVapeagochi, the printed circuit board in 3D

    Vapeagochi

    lucia3e8/vapeagochi

    Eventually I want to target the bc5000 because it's cuter but I'd have to redesign the PCB

    50 parts5
  • 4 layers64 × 41 mmExternal, the printed circuit board in 3D

    External

    agalakhov/klingel-external

    64 parts
  • 2 layers81.3 × 67.3 mmParking system ESP, the printed circuit board in 3D

    Parking system ESP

    BenSchZA/decawave-trilateration-hardware

    Hardware (Kicad schematics and PCB) for a local vehicle tracking solution using trilateration and Decawave technology.

    52 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TPS62203DBV?

Yes. The symbol is Regulator_Switching:TPS62203DBV and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS62203DBV?

SOT-23-5, with 5 pins. Its footprint is drawn on this page.

Where is the TPS62203DBV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS62203DBV?

JLCPCB lists it as part C9051, with 6,354 in stock; the sellers' links on this page open their listings.

What can replace the TPS62203DBV?

Parts like it in the library: the TPS613221ADBV by Texas Instruments, the LM3671MFX-3.3 by Texas Instruments, the ME2108C33M5G by MICRONE and the SGM6013-3.3YTN5G/TR by SG Micro. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS62203DBV?

17 boards in 16 repositories on GitHub; the most starred are listed on this page, with their KiCad files.