

Nikon gps
DIY GPS module for Nikon DSLR
- Size
- 28 × 28 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 42
- Nets
- 25
- Pads
- 112
- Tracks, vias
- 198, 27
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 30 Sep 2018
- Updated
- 14 Mar 2023
Overview
Nikon gps is an open-source printed circuit board by 4x1md, from the 4x1md/nikon_gps repository on GitHub, published under the MIT licence. It is a 2-layer board of 28 × 28 mm with 42 parts on 25 nets, routed with 198 tracks and 27 vias.
It is built around the TPS62203DBV, 74AUP1T08GWH and 74LVC1G14Z, with the SN74LV1T126DBV among its other parts. Its parts include 11 resistors, 10 capacitors, 5 ICs, 3 diodes and 2 inductors. It belongs with the radio and wireless boards of this library.
Main components
4TPS62203DBV
SOT-23-5-40℃~+85℃@(TA) 1 15uA 1MHz 2.5V~6V 3.3V 300mA Buck Buck Built-in Fixed Yes SOT-23-5 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters74AUP1T08GWH
TSSOP-5-1.3mm-40℃~+125℃ 1 1.2uA 2 2.3V~3.6V 2.3V、2.4V、2.55V、2.6V、2.67V、2.72V 310mV、330mV、360mV、440mV、450mV、500mV 4mA 4mA 74AUP Series 7ns@3.3V,30pF AND Gate TSSOP-5-1.3mm Logic Gates ROHSNexperiaLogic Gates74LVC1G14Z
SOT-553-40℃~+125℃ 1 1.2V~3.33V 1.65V~5.5V 200uA 32mA 32mA 6.5ns@5V,50pF 74LVC 750mV~2.35V Power shutdown protection、Noise suppression function Push-pull Schmitt trigger SOT-553 Inverters ROHSDiodes IncorporatedInvertersSN74LV1T126DBV
SOT-23-5-40℃~+125℃ 1 1 1.8V~5.5V CMOS CMOS Tri-State Unidirectional SOT-23-5 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
README
pcb/nikon_gps/README.mdnikon_gps
This directory stores the latest version of the project. Currently, revision B of the PCB developped in KiCAD 5.1.
Parts
42| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10K | Nikon_GPS:R_0603 | R1, R3, R4 |
| 2 | 100nF | Nikon_GPS:C_0402 | C3, C10 |
| 2 | 100nF | Nikon_GPS:C_0603 | C4, C9 |
| 2 | 33 | Nikon_GPS:R_0603 | R2, R6 |
| 2 | 33K | Nikon_GPS:R_0603 | R7, R9 |
| 2 | Green | Nikon_GPS:LED_0805 | D2, D3 |
| 2 | M2 screw | Nikon_GPS:MountingHole_2.2mm_M2_DIN965 | MH1, MH2 |
| 1 | 0.1A | Nikon_GPS:Fuse_0603 | F1 |
| 1 | 100K | Nikon_GPS:R_0603 | R11 |
| 1 | 100nF | Nikon_GPS:C_0805 | C8 |
| 1 | 100nF | Nikon_GPS:C_0805_NarrowPads | C1 |
| 1 | 10uF | Nikon_GPS:C_0805 | C7 |
| 1 | 10uH | Nikon_GPS:L_0805 | L2 |
| 1 | 18pF | Nikon_GPS:C_0402 | C2 |
| 1 | 1PPS | Nikon_GPS:Measurement_Point_Round-SMD-Pad_Small | TP5 |
| 1 | 1nF | Nikon_GPS:C_0603 | C6 |
| 1 | 1x03 pads | Nikon_GPS:Connection_Pads_03 | J1 |
| 1 | 22K | Nikon_GPS:R_0603 | R5 |
| 1 | 3.3V | Nikon_GPS:Measurement_Point_Round-SMD-Pad_Small | TP2 |
| 1 | 330 | Nikon_GPS:R_0603 | R10 |
| 1 | 4.7K | Nikon_GPS:R_0603 | R8 |
| 1 | 4.7uF | Nikon_GPS:C_0805 | C5 |
| 1 | 5V | Nikon_GPS:Measurement_Point_Round-SMD-Pad_Small | TP1 |
| 1 | 600Ohm | Nikon_GPS:L_0805 | L1 |
| 1 | 74AUP1T08 | Nikon_GPS:SOT-353_SC-70-5 | U2 |
| 1 | 74LVC1G14 | Nikon_GPS:SOT-23-5 | U5 |
| 1 | GND | Nikon_GPS:Measurement_Point_Round-SMD-Pad_Small | TP3 |
| 1 | GPS TX | Nikon_GPS:Measurement_Point_Round-SMD-Pad_Small | TP4 |
| 1 | Hornet ORG1411 | Nikon_GPS:ORG1411_GPS_ALT | U1 |
| 1 | NMOS | Nikon_GPS:SOT-323_SC-70 | Q1 |
| 1 | ON/OFF | Nikon_GPS:SW_SPST_PTS645_4pin | SW1 |
| 1 | SN74LV1T126 | Nikon_GPS:SOT-23-5 | U3 |
| 1 | Shottky | Nikon_GPS:D_SOD-523 | D1 |
| 1 | TPS62203DBV | Nikon_GPS:SOT-23-5 | U4 |
More from 4x1md/nikon_gps
1- 2 layers28 × 28 mm

Similar boards
- 4 layers79.9 × 65.2 mm

Ethernet Dev Board
ResonanceGroup/ESP32_Ethernet_Dev_Board
Small dev board for the ESP32 that is meant to incorporate ethernet controller for testing
116 partsMIT - 2 layers25.6 × 40 mm

Sprit
stevegt/sprit
Raspberry Pi I/O interface board for Dynamixel XL-320 (and possibly others)
14 parts1 - 2 layers100 × 54 mm

- 4 layers93 × 155.6 mm

Rocky ctrl
PotatoPeaSea/Rocky
Five-legged walking robot inspired by Rocky (Project Hail Mary).
173 parts - 8 layers120 × 75 mm

- 4 layers35 × 20 mm

Blixten
Alli-Ekundayo/scpt-rl
SCPT-RL trains a cross-attention transformer policy to place PCB components sequentially on a discrete grid. Training has two phases:
60 partsMIT - 4 layers132 × 68.5 mm

- 4 layers45 × 32 mm

Templog mainboard
Michael-Manning/E-Paper-Climate-Logger
Firmware, PCB, and enclosure for the Weathergotchi E-Paper climate logger.
68 parts457MIT
Questions
How big is the Nikon gps PCB?
It measures 28 × 28 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Nikon gps use?
42 parts, built around the TPS62203DBV, 74AUP1T08GWH, 74LVC1G14Z and SN74LV1T126DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Nikon gps KiCad files?
From the 4x1md/nikon_gps repository on GitHub, at the commit this page was made from: the board is pcb/nikon_gps/nikon_gps.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Nikon gps design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).