Skip to the content
12345

LM3671MF-3.3

Texas InstrumentsExtended

-40℃~+85℃@(TA) 1 16uA 2.7V~5.5V 2MHz 3.3V 600mA Buck Buck Built-in Fixed Yes SOT-23-5 DC-DC Converters ROHS

Part id
ti/LM3671MF-3.3
Category
DC DC Converters
Package
SOT-23-5
Pins
5
In stock
994 at JLCPCB (C201586)
Used on
9 open-source boards

Overview

The LM3671MF-3.3 is a DC DC Converter made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+85℃@(TA) 1 16uA 2.7V~5.5V 2MHz 3.3V 600mA Buck Buck Built-in Fixed Yes SOT-23-5 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (LM3671MF-3.3_SOT:LM3671MF-3.3_SOT, from Antmicro) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 994 are in stock at JLCPCB (part C201586). 9 open-source boards in 7 repositories on GitHub use it.

Symbol

1VIN2GND3EN4FB5SW
LM3671MF-3.3_SOT:LM3671MF-3.3_SOTFrom Antmicro

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

14
Supply, least
2.7 V · VIN, recommended operating min · p. 5
Supply, most
5.5 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
6 V · VIN, absolute max · p. 4
Works from
-40 °C · Ambient operating min · p. 5
Works up to
85 °C · Ambient operating max · p. 5
Junction, hottest
125 °C · Junction temperature absolute max · p. 4
Takes working
16 µA · VIN quiescent current typical, no load, not switching · p. 1
Takes asleep
10 nA · Shutdown supply current typical, EN = 0 V · p. 6
Gives
600 mA · Recommended load current max · p. 5
Current limit
1.02 A · Switch peak current limit typical, open loop · p. 6
Switches at
2 MHz · Internal oscillator typical, PWM mode · p. 6
Junction to air (DBV (SOT-23 ))
165.7 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to case (DBV (SOT-23 ))
116.6 K/W · Junction-to-case top thermal resistance · p. 5
Junction to board (DBV (SOT-23 ))
26.8 K/W · Junction-to-board thermal resistance · p. 5

What it is and has

3
Mode switching
Automatic PFM-PWM · p. 1
Soft start
Internal · p. 1
Protection
Soft-start, undervoltage protection, current overload protection, thermal shutdown · p. 12

Specifications

38
ParameterConditionsAs printedPage
VIN pin: voltage to GND VINOver operating free-air temperature rangemin -0.2 · max 6 V4
Junction temperature TJ-MAXmax 125 °C4
Maximum lead temperaturesoldering, 10 sec.max 260 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 Vmax 500 V4
Electrostatic discharge V(ESD)Machine modelmax 200 V4
Input voltageSee output-voltage-dependent input range in footnote (3)min 2.7 · max 5.5 V5
Recommended load currentmin 0 · max 600 mA5
Junction temperature TJmin -40 · max 125 °C5
Ambient temperature TASubject to power-dissipation deratingmin -40 · max 85 °C5
Junction-to-ambient thermal resistance RθJADBV (SOT-23 ), 5 PINStyp 165.7 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DBV (SOT-23 ), 5 PINStyp 116.6 °C/W5
Junction-to-board thermal resistance RθJBDBV (SOT-23 ), 5 PINStyp 26.8 °C/W5
Junction-to-top characterization parameter ψJTDBV (SOT-23 ), 5 PINStyp 13.3 °C/W5
Junction-to-board characterization parameter ψJBDBV (SOT-23 ), 5 PINStyp 26.3 °C/W5
POWER RATINGSOT-23, 4 layer board, RθJA = 165.7°C/W, TA ≤ 25°Cmax 770 mW5
POWER RATINGSOT-23, 4 layer board, RθJA = 165.7°C/W, TA = 60°Cmax 500 mW5
POWER RATINGSOT-23, 4 layer board, RθJA = 165.7°C/W, TA = 85°Cmax 310 mW5
Input voltage VIN−40°C to 125°C, see (4)min 2.7 · max 5.5 V6
Feedback voltage (fixed) MF VFBMF; PWM mode, −40°C to 125°C; VIN = VOUT + 1 V for VOUT ≥ 2.5 Vmin -4 · max 4 %6
Line regulation VFB2.7 V ≤ VIN ≤ 5.5 V, IO = 10 mAtyp 0.031 %/V6
Load regulation VFB100 mA ≤ IO ≤ 600 mA, VIN = 3.6 Vtyp 0.0013 %/mA6
Internal reference voltage VREFTJ = 25°C, VIN = EN = 3.6 Vtyp 0.5 V6
Shutdown supply current ISHDNEN = 0 V, TJ = 25°Ctyp 0.01 uA6
Shutdown supply current ISHDNEN = 0 V, −40°C to 125°Cmax 1 uA6
DC bias current into VIN IQNo load, device is not switching (FB forced higher than programmed output voltage), TJ = 25°Ctyp 16 uA6
DC bias current into VIN IQNo load, device is not switching (FB forced higher than programmed output voltage), −40°C to 125°Cmax 35 uA6
Pin-pin resistance for PFET RDSON (P)VIN = VGS = 3.6 Vtyp 380 · max 500 mΩ6
Pin-pin resistance for NFET RDSON (N)VIN = VGS= 3.6 Vtyp 250 · max 400 mΩ6
Switch peak current limit ILIMOpen loop, TJ = 25°Ctyp 1020 mA6
Switch peak current limit ILIMOpen loop (7), −40°C to 125°Cmin 830 · max 1150 mA6
Logic high input VIH−40°C to 125°Cmin 1 V6
Logic low input VIL−40°C to 125°Cmax 0.4 V6
Enable (EN) input current IENTJ = 25°C, VIN = EN = 3.6 Vtyp 0.01 uA6
Enable (EN) input current IEN−40°C to 125°Cmax 1 uA6
Internal oscillator frequency ƒOSCPWM Mode (5), TJ = 25°Ctyp 2 MHz6
Internal oscillator frequency ƒOSCPWM Mode (5), −40°C to 125°Cmin 1.6 · max 2.6 MHz6

Pins, by the datasheet

5
1 VIN
Power supply input; connect to the input filter capacitor. · p. 3
2 GND
Ground pin. · p. 3
3 EN
Enable input; shutdown below 0.4 V and enabled above 1 V; do not leave floating. · p. 3
4 FB
Feedback analog input; connect directly to the output filter capacitor for fixed voltage versions. · p. 3
5 SW
Switching node connected to the internal PFET switch and NFET synchronous rectifier. · p. 3

Open-source boards using it

9See all 9
  • 2 layers87 × 84.1 mmOpenACE V0.0.2, the printed circuit board in 3D

    OpenACE V0.0.2

    gatasConspicuity/gatas

    eConspicuity with support for ADS-L, OGN, FLARM, FANET for General Aviation

    80 parts26GPL-3.0
  • 2 layers47.2 × 69.6 mmSdmplayerv0.01, the printed circuit board in 3D

    Sdmplayerv0.01

    SL-RU/sdmplayer

    This is sources of my DIY music player based on STM32 MCU and VS1053 codec

    78 parts26MIT
  • 2 layers50 × 100 mmSpoke, the printed circuit board in 3D

    Spoke

    FeruzTopalov/spoke

    Standalone LoRa-based real-time off-grid relative GPS navigation for group of up to 5 people. Improved version of LRNS Eleph

    143 parts16GPL-3.0
  • 2 layers78 × 40 mmNode base, the printed circuit board in 3D

    Node base

    LanternD/NB-Scope

    Hardware and software design for NB-Scope.

    79 parts6Apache-2.0
  • 2 layers57 × 47 mm4layerPhil, the printed circuit board in 3D

    4layerPhil

    Czarne-oczki/PCB-Design-with-OLED-display

    58 parts
  • 2 layers22 × 12.5 mmPowerSupply, the printed circuit board in 3D

    PowerSupply

    volium/PowerSupply_lm3671

    Schematic and PCB design of 3.3 V and 600 mA power supply using LM3671

    10 parts
  • 2 layers46 × 124.8 mmLazy Mouse, the printed circuit board in 3D

    Lazy Mouse

    WeBuildAnything/Wireless-Media-Control-Mouse

    The IMU sensor uses the MPU6050 library by Electronic Cats.

    62 parts
  • 2 layers78 × 40 mmNode base, the printed circuit board in 3D

    Node base

    LanternD/NB-Scope

    Hardware and software design for NB-Scope.

    73 parts6Apache-2.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the LM3671MF-3.3?

Yes. The symbol is LM3671MF-3.3_SOT:LM3671MF-3.3_SOT and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LM3671MF-3.3?

SOT-23-5, with 5 pins. Its footprint is drawn on this page.

Where is the LM3671MF-3.3 datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the LM3671MF-3.3?

JLCPCB lists it as part C201586, with 994 in stock; the sellers' links on this page open their listings.

What can replace the LM3671MF-3.3?

Parts like it in the library: the TPS613221ADBV by Texas Instruments, the LM3671MFX-3.3 by Texas Instruments, the SGM6013-3.3YTN5G/TR by SG Micro and the XC9145B33CMR-G by Torex Semiconductor. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LM3671MF-3.3?

9 boards in 7 repositories on GitHub; the most starred are listed on this page, with their KiCad files.