

Vapeagochi
Eventually I want to target the bc5000 because it's cuter but I'd have to redesign the PCB
- Size
- 36 × 36 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 56
- Pads
- 167
- Tracks, vias
- 353, 112
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 11 Dec 2024
- Updated
- 12 Nov 2025
Overview
Vapeagochi is an open-source printed circuit board by lucia3e8, from the lucia3e8/vapeagochi repository on GitHub. It is a 4-layer board of 36 × 36 mm with 50 parts on 56 nets, routed with 353 tracks and 112 vias.
It is built around the TPS62203DBV, IRLML6344TRPBF and TS-1088-AR02016, with the SI2301CDS-T1-GE3 and WS2812B among its other parts. Its parts include 18 resistors, 11 capacitors, 4 connectors, 3 ICs and 3 switches. It belongs with the STM32 boards of this library.
Main components
5TPS62203DBV
SOT-23-5-40℃~+85℃@(TA) 1 15uA 1MHz 2.5V~6V 3.3V 300mA Buck Buck Built-in Fixed Yes SOT-23-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersIRLML6344TRPBF
SOT-23-55℃~+150℃ 1 N-channel 1.1V 1.3W 29mΩ@4.5V 30V 46pF 5A 6.8nC 650pF SOT-23 MOSFETs ROHSInfineon TechnologiesMOSFETsTS-1088-AR02016
SMD,4x3mm-30℃~+80℃ 1.6N 100,000 cycles 12V 2mm 3.9mm 3mm 50mA Black Round Button SMD(SMT) Tab SPST Surface Mount,Vertical Without Bracket SMD,4x3mm Tactile Switches ROHSXUNPUTactile SwitchesSI2301CDS-T1-GE3
SOT-23-55℃~+150℃ 1 P-Channel 1.6W 10nC@4.5V 142mΩ@2.5V 1V 20V 3.1A 405pF 55pF 75pF P-Channel SOT-23 MOSFETs ROHSVishay IntertechnologyMOSFETsWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
readme.mdtamagotchi that dies if you stop vaping
...has been rewritten in Rust. we also made it die if you keep vaping. It counts how many times you've hit it and once you're at the dialy limit, turns off the heating coil.
dirs
.
├── assets # animation sprites etc
├── case # fusion360 files for 3d-printed case
├── ee # kicad, components, assembly
├── readme.txt # you are here
├── scripts # one offs
├── vg2 # vestigial C++ stm32ide build
└── vgrs # new rust build <- USE THIS ONEHardware
Case
Initially we used a bc5000 vape because it's small and cute. Right now bc5000 is too small to fit all the hardware, so we use a gimi30k instead.
Eventually I want to target the bc5000 because it's cuter but I'd have to redesign the PCB

Pinout
| Pin | Function |
|------|-----------------|
| PA5 | SCREEN_CLK |
| PA6 | SCREEN_RES |
| PA7 | SCREEN_DIN |
| PA8 | SCREEN_DC |
| PB10 | SCREEN_CS |
| PB3 | Left Button |
| PA0 | Middle Button |
| PB2 | Right Button |
| PA4 | Coil Input |
| PB11 | Coil Enable |
| PA1 | Programmable LED|By default, the vape's heating coil is disabled via a MOSFET. Pull PB11 (Coil Enable) high to allow the coil to turn on when user hits the vape.
When user tries to hit the vape, PA4 (Coil Input) will go high, regardless of PB11 state.
Software
Building
Either use nix-shell, or manually install cargo with thumbv6m-none-eabi target and probe-rs.
cd vgrs
nix-shell
cargo build --release --target thumbv6m-none-eabi # build
sudo probe-rs run --chip STM32L072CBTx target/thumbv6m-none-eabi/release/vgrs # flashParts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 330 | Resistor_SMD:R_0402_1005Metric | R3, R7, R8, R11, R12, R13, R14, R15 |
| 6 | 1uF | Capacitor_SMD:C_0402_1005Metric | C4, C7, C8, C9, C10, C11 |
| 4 | 100k | Resistor_SMD:R_0402_1005Metric | R4, R5, R6, R22 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 3 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C1, C5, C6 |
| 3 | TS-1088-AR02016 | TS-1088-AR02016:SW_TS-1088-AR02016 | S1, S2, S3 |
| 2 | 12pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 20k | Resistor_SMD:R_0402_1005Metric | R23, R24 |
| 2 | Conn_01x07 | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J1, J4 |
| 1 | 100 | PCM_JLCPCB:R_0805 | R9 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 10uH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 1M | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 1k | PCM_JLCPCB:R_0402 | R10 |
| 1 | 2N7002 | PCM_JLCPCB:Q_SOT-23 | Q1 |
| 1 | 32768Hz - 12,5 pF | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | BOOT0 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | Conn_01x03 | Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_Horizontal | J3 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | IRLML6344TRPBF | IRLML6344TRPBF:SOT95P240X112-3N | U2 |
| 1 | SI2301CDS-T1-GE3 | PCM_JLCPCB:Q_SOT-23 | Q3 |
| 1 | STM32L072CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U3 |
| 1 | Speaker_Crystal | Buzzer_Beeper:Buzzer_CUI_CPT-9019S-SMT | LS1 |
| 1 | TPS62203DBV | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | WS2812B | PCM_JLCPCB:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D2 |
Similar boards
- 4 layers64 × 41 mm

- 4 layers35.4 × 21.6 mm

ESP32-C3-V4
Ans1S/esp32-c3-iot-sensor-board
Open-source ESP32-C3 platform for ultra-low-power environmental sensor networks powered by recycled LiPo cells. Includes KiCad PCB, PlatformIO firmware (ESP-NOW + ThingSpeak), BME280/BME680 support, deep-sleep…
57 parts6MIT - 2 layers131.5 × 83.5 mm

Badge esp32-s3
BYU-I-eBadge/e-badge
A hackable eBadge platform for students — a customizable, programmable electronics badge designed for hands-on learning and creative exploration throughout their academic journey.
214 parts2MIT - 4 layers50 × 111 mm

- 2 layers149.6 × 127.1 mm

- 2 layers467.5 × 140 mm

- 4 layers45 × 32 mm

Templog mainboard
Michael-Manning/E-Paper-Climate-Logger
Firmware, PCB, and enclosure for the Weathergotchi E-Paper climate logger.
68 parts457MIT - 2 layers45 × 58.2 mm

Questions
How big is the Vapeagochi PCB?
It measures 36 × 36 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Vapeagochi use?
50 parts, built around the TPS62203DBV, IRLML6344TRPBF, TS-1088-AR02016 and SI2301CDS-T1-GE3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Vapeagochi KiCad files?
From the lucia3e8/vapeagochi repository on GitHub, at the commit this page was made from: the board is ee/vg.kicad_pcb and its schematic ee/vg.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Vapeagochi design in my own project?
Its repository states no licence, so its author keeps all rights: ask lucia3e8 before reusing the design.