
TLV70033DDC
Texas InstrumentsExtended
-40℃~+125℃@(Tj) 1 200mA 3.3V 31uA 48uVrms 5.5V 68dB Fixed Over Current Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS
- Part id
- ti/TLV70033DDC
- Category
- Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
- Package
- SOT-23-5
- Pins
- 5
- In stock
- 23,389 at JLCPCB (C11337)
- Used on
- 7 open-source boards
Overview
The TLV70033DDC is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+125℃@(Tj) 1 200mA 3.3V 31uA 48uVrms 5.5V 68dB Fixed Over Current Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.
PCBKit's library has its KiCad symbol (Pinmap_Generic:Regulator_Linear_1IN_2GND_3EN_4NC_5OUT, from PCBKit's generic symbols) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 23,389 are in stock at JLCPCB (part C11337). 7 open-source boards in 6 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
11- Supply, least
- 2 V · VIN, recommended operating min · p. 5
- Supply, most
- 5.5 V · VIN, recommended operating max · p. 5
- Supply, absolute maximum
- 6 V · VIN, absolute max · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature, absolute max · p. 5
- Takes working
- 31 µA · Ground pin current, typical, IOUT = 0 mA · p. 6
- Takes asleep
- 1 µA · Shutdown ground current, typical, VEN ≤ 0.4 V, VIN = 2 to 4.5 V · p. 6
- Gives
- 200 mA · IOUT, recommended continuous output max · p. 5
- Current limit
- 220 mA · Output current limit min, VOUT = 0.9 × VOUT(nom) · p. 6
- Junction to air (DDC [SOT])
- 235.9 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to board (DDC [SOT])
- 54 K/W · Junction-to-board thermal resistance · p. 5
- Junction to case (DDC [SOT])
- 61.9 K/W · Junction-to-case (top) thermal resistance · p. 5
What it is and has
4- Accuracy
- 2% · p. 1
- Quiescent current
- 31 μA · p. 1
- Protection
- Thermal shutdown and overcurrent protection · p. 1
- Output capacitor stability
- Effective capacitance of 0.1 μF · p. 1
Around it
2- cap 1 μF
- between IN and GND; Ceramic capacitor recommended for stability and good transient performance; X5R or X7R recommended on page 13. · p. 4
- cap 1 μF
- between OUT and GND; Ceramic capacitor for stability; X5R or X7R recommended. Effective capacitance under bias and temperature must be at least 0.1 uF; maximum ESR less than 200 mΩ. · p. 4
Specifications
32| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Voltage VIN | Over operating junction temperature range | min -0.3 · max 6 V | 5 |
| Voltage VEN | Maximum is VIN + 0.3 V or 6 V, whichever is less | min -0.3 · max 6 V | 5 |
| Voltage VOUT | Over operating junction temperature range | min -0.3 · max 6 V | 5 |
| Temperature TJ | Operating junction | min -55 · max 150 °C | 5 |
| Temperature Tstg | Storage | min -55 · max 150 °C | 5 |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; rating ±2000 V | max 2000 V | 5 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; rating ±500 V | max 500 V | 5 |
| VIN VIN | Over operating free-air temperature range | min 2 · max 5.5 V | 5 |
| VOUT VOUT | Family output-voltage range; over operating free-air temperature range | min 1.2 · max 4.8 V | 5 |
| IOUT IOUT | Over operating free-air temperature range | min 0 · max 200 mA | 5 |
| Junction-to-ambient thermal resistance RθJA | DDC [SOT], 5 PINS | typ 235.9 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | DDC [SOT], 5 PINS | typ 61.9 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | DDC [SOT], 5 PINS | typ 54 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | DDC [SOT], 5 PINS | typ 0.8 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | DDC [SOT], 5 PINS | typ 53.4 °C/W | 5 |
| Input voltage range VIN | min 2 · max 5.5 V | 6 | |
| DC output accuracy VOUT | –40°C ≤ TJ ≤ +125°C | min -2 · max 2 % | 6 |
| Line regulation ΔVOUT(ΔVIN) | VOUT(nom) + 0.3 V ≤ VIN ≤ 5.5 V, IOUT = 10 mA | typ 1 · max 5 mV | 6 |
| Load regulation ΔVOUT(ΔIOUT) | 0 mA ≤ IOUT ≤ 200 mA | typ 1 · max 15 mV | 6 |
| Output current limit ICL | VOUT = 0.9 × VOUT(nom) | min 220 · max 860 mA | 6 |
| Ground pin current IGND | IOUT = 0 mA | typ 31 · max 55 uA | 6 |
| Ground pin current IGND | IOUT = 200 mA, VIN = VOUT + 0.5 V | typ 270 uA | 6 |
| Ground pin current (shutdown) ISHDN | VEN ≤ 0.4 V, VIN = 2 V | typ 400 nA | 6 |
| Ground pin current (shutdown) ISHDN | VEN ≤ 0.4 V, 2 V ≤ VIN ≤ 4.5 V | typ 1 · max 2 uA | 6 |
| Start-up time tSTR | COUT = 1 uF, IOUT = 200 mA; time from EN assertion to 0.98 × VOUT(nom) | typ 100 us | 6 |
| Enable pin high (enabled) VEN(high) | Maximum is VIN | min 0.9 V | 6 |
| Enable pin low (disabled) VEN(low) | min 0 · max 0.4 V | 6 | |
| Enable pin current IEN | VIN = VEN = 5.5 V | typ 0.04 · max 0.5 uA | 6 |
| Undervoltage lockout UVLO | VIN rising | typ 1.9 V | 6 |
| Thermal shutdown temperature Tsd | Shutdown, temperature increasing | typ 160 °C | 6 |
| Thermal shutdown temperature Tsd | Reset, temperature decreasing | typ 140 °C | 6 |
| Operating junction temperature TJ | min -40 · max 125 °C | 6 |
Pins, by the datasheet
5- 1 IN
- Input pin; a 1-uF ceramic capacitor to ground is recommended for stability and transient performance. · p. 4
- 2 GND
- Ground pin. · p. 4
- 3 EN
- Enable pin; above 0.9 V enables the regulator and below 0.4 V puts it into shutdown. · p. 4
- 4 NC
- No connection; can be tied to ground to improve thermal dissipation. · p. 4
- 5 OUT
- Regulated output voltage pin; a 1-uF ceramic capacitor to ground is needed for stability. · p. 4
Open-source boards using it
7- 2 layers45.9 × 14.2 mm

- 2 layers66 × 37.6 mm

Controller
marenz2569/led-controller-ethernet
led-controller-ethernet is the hardware to the avr-ethernet-licht firmware https://github.com/marenz2569/avr-ethernet-licht
35 partsLGPL-2.1 - 4 layers18.8 × 35.8 mm

- 4 layers18.8 × 35.8 mm

Mdbt42 breakout
shraken/mdbt42q_bobby
A MDBT42Q break-out board for Nordic nRF52832 chip family
18 partsMIT - 2 layers27.4 × 33.5 mm

SensactSe
klaus-liebler/sensact
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier…
25 parts4Apache-2.0 - 2 layers71 × 71 mm

SensactUp
klaus-liebler/sensact
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier…
99 parts4Apache-2.0 - 4 layers100 × 100 mm

Parts like it
8ME6211C33M5G-N
SOT-23-5-40℃~+150℃ 1 120mV@(100mA) 3.3V 500mA 50uVrms 60uA 6V 70dB@(1kHz) Fixed Over Current Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSPX3819M5-L-3-3/TR
SOT-23-5-40℃~+125℃ 1 16V 3.3V 340mV@(500mA) 40uVrms 500mA 70dB 90uA Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMaxLinearVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsRT9013-33GB
SOT-23-5-40℃~+125℃@(Tj) 1 25uA 3.3V 30uVrms 400mV@(500mA) 5.5V 500mA 50dB@(10kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRICHTEKVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsXC6219B332MR
SOT-23-5-20℃~+60℃ 1 15uA 280mV@(100mA) 3.3V 300mA 40dB@(1kHz) 7V Fixed Over Current Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUMWVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPS7A2033PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 10uVrms 140mV@(300mA) 3.3V 300mA 65dB@(100kHz) 6V 8.5uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge、Built-in soft-start Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPLP5907MFX-3.3
SOT-23-51 200mV@(300mA) 2uA 3.3V 300mA 5.5V 51uVrms 75dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsRT9078-33GJ5
TSOT-23-5-40℃~+125℃@(Tj) 1 150mV@(300mA) 2uA 3.3V 300mA 5.5V 51uVrms 75dB Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRichtek TechVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV75533PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 238mV@(500mA) 25uA 3.3V 46dB@(100kHz) 5.5V 500mA 71.5uVrms Fixed Over Current Protection、Thermal Shutdown、Input undervoltage protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Questions
Is there a KiCad symbol and footprint for the TLV70033DDC?
Yes. The symbol is Pinmap_Generic:Regulator_Linear_1IN_2GND_3EN_4NC_5OUT and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TLV70033DDC?
SOT-23-5, with 5 pins. Its footprint is drawn on this page.
Where is the TLV70033DDC datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TLV70033DDC?
JLCPCB lists it as part C11337, with 23,389 in stock; the sellers' links on this page open their listings.
What can replace the TLV70033DDC?
Parts like it in the library: the ME6211C33M5G-N by MICRONE, the SPX3819M5-L-3-3/TR by MaxLinear, the RT9013-33GB by RICHTEK and the XC6219B332MR by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TLV70033DDC?
7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.