Skip to the content
123456789101112131415161718192021222324

TCA9535PW

Texas InstrumentsExtended

-40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 16 25mA 400kHz 4V 8 I2C、SMBus Interrupt Output Push-Pull Reset function、Cascade and address expansion、Built-in LED driver TSSOP-24 I/O Expanders ROHS

Part id
ti/TCA9535PW
Category
I, O Expanders
Package
TSSOP-24
Pins
24
In stock
19,042 at JLCPCB (C130204)
Used on
4 open-source boards

Overview

The TCA9535PW is an i, O Expander made by Texas Instruments in a TSSOP-24 package with 24 pins. -40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 16 25mA 400kHz 4V 8 I2C、SMBus Interrupt Output Push-Pull Reset function、Cascade and address expansion、Built-in LED driver TSSOP-24 I/O Expanders ROHS.

PCBKit's library has its KiCad symbol (Interface_Expansion:TCA9535PWR, from KiCad's library) and its footprint (Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm, from KiCad's library), ready for a KiCad board. 19,042 are in stock at JLCPCB (part C130204). 4 open-source boards in 2 repositories on GitHub use it.

Symbol

1INT2A13A24P005P016P027P038P049P0510P0611P0712GND13P1014P1115P1216P1317P1418P1519P1620P1721A022SCL23SDA24VCC
Interface_Expansion:TCA9535PWRFrom KiCad's library

Footprint

123456789101112131415161718192021222324
Package_SO:TSSOP-24_4.4x7.8mm_P0.65mmFrom KiCad's library

From the datasheet

14
Supply, least
1.65 V · VCC, recommended operating min · p. 6
Supply, most
5.5 V · VCC, recommended operating max · p. 6
Supply, absolute maximum
6 V · VCC, absolute max · p. 5
Works from
-40 °C · Operating free-air temperature min · p. 6
Works up to
125 °C · Operating free-air temperature max · p. 6
Junction, hottest
130 °C · Junction temperature absolute max · p. 5
Takes working
22 µA · VCC, operating typical at 5.5V, 400kHz, inputs, no load · p. 7
Takes at most
40 µA · VCC, operating max at 5.5V, 400kHz, inputs, no load · p. 7
Takes asleep
1.5 µA · VCC, standby typical at 5.5V, VI = VCC, -40°C < TA ≤ 85°C · p. 7
A pin gives at most
50 mA · P-port continuous output low current absolute max · p. 5
Junction to air (PW (TSSOP))
108.8 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to board (PW (TSSOP))
62.8 K/W · Junction-to-board thermal resistance · p. 6
Junction to case (PW (TSSOP))
54 K/W · Junction-to-case top thermal resistance · p. 6
Data rate, most
400 kbit/s · I2C fast mode clock max · p. 8

What it is and has

8
Interface
I2C to parallel port expander · p. 1
I/O width
16-bit · p. 1
I2C clock
400kHz fast I2C bus · p. 1
Interrupt output
Open-drain active-low · p. 1
I/O tolerance
5V tolerant I/O ports · p. 1
Polarity inversion
Polarity inversion register · p. 1
Hardware addressing
Three hardware address pins · p. 1
Package option
PW (TSSOP, 24) · p. 1

Specifications

111
ParameterConditionsAs printedPage
Supply voltage VCCOver operating free-air temperature rangemin -0.5 · max 6 V5
Input voltage VIOver operating free-air temperature range; footnote (2)min -0.5 · max 6 V5
Output voltage VOOver operating free-air temperature range; footnote (2)min -0.5 · max 6 V5
Input clamp current IIKVI < 0max -20 mA5
Output clamp current IOKVO < 0max -20 mA5
Input-output clamp current IIOKVO < 0 or VO > VCC; ±20 mA limitmax 20 mA5
Continuous output low current IOLVO = 0 to VCCmax 50 mA5
Continuous output high current IOHVO = 0 to VCCmax -50 mA5
Continuous current through GND ICCmax -250 mA5
Continuous current through VCC ICCmax 160 mA5
Maximum junction temperature Tj(MAX)max 130 °C5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 V ratingmax 2000 V5
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1000 V ratingmax 1000 V5
Supply voltage VCCmin 1.65 · max 5.5 V6
High-level input voltage VIHA2–A0, P07–P00, P17–P10; min 0.7 × VCCmax 5.5 V6
Low-level input voltage VILSCL, SDA, A2–A0, P07–P00, P17–P10; max 0.3 × VCCmin -0.5 V6
High-level output current IOHP07–P00, P17–P10max -10 mA6
Low-level output current IOLP07–P00, P17–P10; Tj ≤ 65°Cmax 25 mA6
Low-level output current IOLP07–P00, P17–P10; Tj ≤ 85°Cmax 18 mA6
Low-level output current IOLP07–P00, P17–P10; Tj ≤ 100°Cmax 11 mA6
Low-level output current IOLP07–P00, P17–P10; Tj ≤ 130°Cmax 5 mA6
Low-level output current IOLINT, SDA; Tj ≤ 85°Cmax 6 mA6
Low-level output current IOLINT, SDA; Tj ≤ 100°Cmax 3.5 mA6
Low-level output current IOLINT, SDA; Tj ≤ 130°Cmax 1 mA6
Operating free-air temperature TAmin -40 · max 125 °C6
Junction-to-ambient thermal resistance RθJAPW (TSSOP), 24 PINStyp 108.8 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)PW (TSSOP), 24 PINStyp 54 °C/W6
Junction-to-board thermal resistance RθJBPW (TSSOP), 24 PINStyp 62.8 °C/W6
Junction-to-top characterization parameter ψJTPW (TSSOP), 24 PINStyp 11.1 °C/W6
Junction-to-board characterization parameter ψJBPW (TSSOP), 24 PINStyp 62.3 °C/W6
Input diode clamp voltage VIKII = –18mA; VCC = 1.65V to 5.5Vmin -1.2 V7
Power-on reset voltage, VCC rising VPORRVI = VCC or GND, IO = 0typ 1.2 · max 1.5 V7
Power-on reset voltage, VCC falling VPORFVI = VCC or GND, IO = 0min 0.75 · typ 1 V7
P-port high-level output voltage VOHIOH = –8mA; VCC = 1.65Vmin 1.2 V7
P-port high-level output voltage VOHIOH = –8mA; VCC = 2.3Vmin 1.8 V7
P-port high-level output voltage VOHIOH = –8mA; VCC = 3Vmin 2.6 V7
P-port high-level output voltage VOHIOH = –8mA; VCC = 4.75Vmin 4.1 V7
P-port high-level output voltage VOHIOH = –10mA; VCC = 1.65Vmin 1 V7
P-port high-level output voltage VOHIOH = –10mA; VCC = 2.3Vmin 1.7 V7
P-port high-level output voltage VOHIOH = –10mA; VCC = 3Vmin 2.5 V7
P-port high-level output voltage VOHIOH = –10mA; VCC = 4.75Vmin 4 V7
Low-level output current IOLSDA; VOL = 0.4V; VCC = 1.65V to 5.5Vmin 3 mA7
Low-level output current IOLP port; VOL = 0.5V; VCC = 1.65V to 5.5Vmin 8 mA7
Low-level output current IOLP port; VOL = 0.7V; VCC = 1.65V to 5.5Vmin 10 mA7
Low-level output current IOLINT; VOL = 0.4V; VCC = 1.65V to 5.5Vmin 3 mA7
Input leakage current IISCL, SDA Input leakage; VI = VCC or GND; VCC = 1.65V to 5.5V; ±1 uA limitmax 1 uA7
Input leakage current IIA2–A0 Input leakage; VI = VCC or GND; VCC = 1.65V to 5.5V; ±1 uA limitmax 1 uA7
Input high leakage current IIHP port; VI = VCC; VCC = 1.65V to 5.5Vmax 1 uA7
Input low leakage current IILP port; VI = GND; VCC = 1.65V to 5.5Vmax -1 uA7
Quiescent current ICCOperating mode; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400kHz, No load; VCC = 5.5Vtyp 22 · max 40 uA7
Quiescent current ICCOperating mode; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400kHz, No load; VCC = 3.6Vtyp 11 · max 30 uA7
Quiescent current ICCOperating mode; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400kHz, No load; VCC = 2.7Vtyp 8 · max 19 uA7
Quiescent current ICCOperating mode; VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400kHz, No load; VCC = 1.95Vtyp 5 · max 11 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 5.5Vtyp 1.5 · max 3.9 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 3.6Vtyp 0.9 · max 2.2 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 2.7Vtyp 0.6 · max 1.8 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 1.95Vtyp 0.6 · max 1.5 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 5.5Vmax 8.5 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 3.6Vmax 5 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 2.7Vmax 4 uA7
Quiescent current ICCStandby mode; VI = VCC, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 1.95Vmax 3.5 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 5.5Vtyp 1.5 · max 8.7 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 3.6Vtyp 0.9 · max 4 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 2.7Vtyp 0.6 · max 3 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 85°C; VCC = 1.95Vtyp 0.4 · max 2.2 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 5.5Vmax 26 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 3.6Vmax 13 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 2.7Vmax 9 uA7
Quiescent current ICCStandby mode; VI = GND, IO = 0, I/O = inputs, fSCL = 0kHz, No load, -40°C < TA ≤ 125°C; VCC = 1.95Vmax 7 uA7
Input capacitance CISCL; VI = VCC or GND; VCC = 1.65V to 5.5Vtyp 3 · max 8 pF7
Input-output pin capacitance CioSDA; VIO = VCC or GND; VCC = 1.65V to 5.5Vtyp 3 · max 9.5 pF8
Input-output pin capacitance CioP port; VIO = VCC or GND; VCC = 1.65V to 5.5Vtyp 3.7 · max 9.5 pF8
I2C clock frequency fsclI2C BUS—STANDARD MODEmin 0 · max 100 kHz8
I2C clock high time tschI2C BUS—STANDARD MODEmin 4 us8
I2C clock low time tsclI2C BUS—STANDARD MODEmin 4.7 us8
I2C spike time tspI2C BUS—STANDARD MODEmax 50 ns8
I2C serial-data setup time tsdsI2C BUS—STANDARD MODEmin 250 ns8
I2C serial-data hold time tsdhI2C BUS—STANDARD MODEmin 0 ns8
I2C input rise time ticrI2C BUS—STANDARD MODEmax 1000 ns8
I2C input fall time ticfI2C BUS—STANDARD MODEmax 300 ns8
I2C output fall time tocfI2C BUS—STANDARD MODE; 10pF to 400pF busmax 300 ns8
I2C bus free time between stop and start tbufI2C BUS—STANDARD MODEmin 4.7 us8
I2C start or repeated start condition setup tstsI2C BUS—STANDARD MODEmin 4.7 us8
I2C start or repeated start condition hold tsthI2C BUS—STANDARD MODEmin 4 us8
I2C stop condition setup tspsI2C BUS—STANDARD MODEmin 4 us8
Valid data time tvd(data)I2C BUS—STANDARD MODE; SCL low to SDA output validmax 3.45 us8
Valid data time of ACK condition tvd(ack)I2C BUS—STANDARD MODE; ACK signal from SCL low to SDA (out) lowmax 3.45 us8
I2C bus capacitive load CbI2C BUS—STANDARD MODEmax 400 pF8
I2C clock frequency fsclI2C BUS—FAST MODEmin 0 · max 400 kHz8
I2C clock high time tschI2C BUS—FAST MODEmin 0.6 us8
I2C clock low time tsclI2C BUS—FAST MODEmin 1.3 us8
I2C spike time tspI2C BUS—FAST MODEmax 50 ns8
I2C serial-data setup time tsdsI2C BUS—FAST MODEmin 100 ns8
I2C serial-data hold time tsdhI2C BUS—FAST MODEmin 0 ns8
I2C input rise time ticrI2C BUS—FAST MODEmin 20 · max 300 ns8
I2C input fall time ticfI2C BUS—FAST MODE; min 20 × (VCC / 5.5V) nsmax 300 ns8
I2C output fall time tocfI2C BUS—FAST MODE; 10pF to 400pF bus; min 20 × (VCC / 5.5V) nsmax 300 ns8
I2C bus free time between stop and start tbufI2C BUS—FAST MODEmin 1.3 us8
I2C start or repeated start condition setup tstsI2C BUS—FAST MODEmin 0.6 us8
I2C start or repeated start condition hold tsthI2C BUS—FAST MODEmin 0.6 us8
I2C stop condition setup tspsI2C BUS—FAST MODEmin 0.6 us8
Valid data time tvd(data)I2C BUS—FAST MODE; SCL low to SDA output validmax 0.9 us8
Valid data time of ACK condition tvd(ack)I2C BUS—FAST MODE; ACK signal from SCL low to SDA (out) lowmax 0.9 us9
I2C bus capacitive load CbI2C BUS—FAST MODEmax 400 pF9
Interrupt valid time tivP port to INT; CL ≤ 100pF; over recommended operating free-air temperature rangemax 4 us9
Interrupt reset delay time tirSCL to INT; CL ≤ 100pF; over recommended operating free-air temperature rangemax 4 us9
Output data valid; For VCC = 2.3V–5.5V tpvSCL to P port; CL ≤ 100pF; over recommended operating free-air temperature rangemax 200 ns9
Output data valid; For VCC = 1.65V–2.3V tpvSCL to P port; CL ≤ 100pF; over recommended operating free-air temperature rangemax 300 ns9
Input data setup time tpsP port to SCL; CL ≤ 100pF; over recommended operating free-air temperature rangemin 150 ns9
Input data hold time tphP port to SCL; CL ≤ 100pF; over recommended operating free-air temperature rangemin 1 us9

Open-source boards using it

4
  • 2 layersRCShield, the printed circuit board in 3D

    RCShield

    Maddimax/MadControl

    OpenSource remote control

    37 parts1
  • 6 layers178 × 118 mmMoriShield Carrier 6L, the printed circuit board in 3D

    MoriShield Carrier 6L

    aswinserigreen/morishield_hardware

    all components bom , pcb layouts and schematics of morishield is maintained here

    157 parts
  • 2 layersDigitalBoard, the printed circuit board in 3D

    DigitalBoard

    Maddimax/MadControl

    OpenSource remote control

    24 parts1
  • 2 layersIOBreakout, the printed circuit board in 3D

    IOBreakout

    Maddimax/MadControl

    OpenSource remote control

    6 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TCA9535PW?

Yes. The symbol is Interface_Expansion:TCA9535PWR and the footprint Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TCA9535PW?

TSSOP-24, with 24 pins. Its footprint is drawn on this page.

Where is the TCA9535PW datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TCA9535PW?

JLCPCB lists it as part C130204, with 19,042 in stock; the sellers' links on this page open their listings.

What can replace the TCA9535PW?

Parts like it in the library: the PCA9555PW by NXP Semiconductors, the TCA9555PW by Texas Instruments, the PCA9539PW by NXP Semiconductors and the PCA9535PW by NXP Semiconductors. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TCA9535PW?

4 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.