TCA9539PW
Texas InstrumentsExtended
-40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 16 25mA 4 4.1V 400kHz 400mV I2C、SMBus Interrupt Output Push-Pull Reset function、Cascading and address extension、Built-in LED driver TSSOP-24 I/O Expanders ROHS
- Part id
- ti/TCA9539PW
- Category
- I, O Expanders
- Package
- TSSOP-24
- Pins
- 24
- In stock
- 8,429 at JLCPCB (C131972)
Overview
The TCA9539PW is an i, O Expander made by Texas Instruments in a TSSOP-24 package with 24 pins. -40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 16 25mA 4 4.1V 400kHz 400mV I2C、SMBus Interrupt Output Push-Pull Reset function、Cascading and address extension、Built-in LED driver TSSOP-24 I/O Expanders ROHS.
PCBKit's library has its KiCad symbol (Analog & Interface:TCA9539PWR, from CERN's library) and its footprint (Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm, from KiCad's library), ready for a KiCad board. 8,429 are in stock at JLCPCB (part C131972).
Symbol
Footprint
From the datasheet
13- Supply, least
- 1.65 V · VCC, recommended operating min · p. 5
- Supply, most
- 5.5 V · VCC, recommended operating max · p. 5
- Supply, absolute maximum
- 6 V · VCC, absolute max · p. 5
- Works from
- -40 °C · Operating free-air temperature min · p. 5
- Works up to
- 85 °C · Operating free-air temperature max · p. 5
- Junction, hottest
- 100 °C · Junction temperature absolute max · p. 5
- Takes working
- 22 µA · VCC operating typical, 5.5 V, inputs, 400 kHz, no load · p. 7
- Takes at most
- 40 µA · VCC operating max, 5.5 V, inputs, 400 kHz, no load · p. 7
- Takes asleep
- 1.5 µA · VCC standby typical, 5.5 V, inputs at VCC, no load · p. 7
- A pin gives at most
- 50 mA · Continuous output low current absolute max · p. 5
- Junction to air (PW (TSSOP))
- 108.8 K/W · Junction-to-ambient thermal resistance · p. 6
- Junction to board (PW (TSSOP))
- 62.8 K/W · Junction-to-board thermal resistance · p. 6
- Junction to case (PW (TSSOP))
- 54 K/W · Junction-to-case (top) thermal resistance · p. 6
What it is and has
11- I/O expansion
- 16-bit I2C and SMBus · p. 1
- Interrupt
- Open-drain active-low output · p. 1
- Reset
- Active-low reset input · p. 1
- I/O tolerance
- 5 V · p. 1
- I2C
- 400-kHz Fast mode · p. 1
- Configuration
- Input and output configuration register · p. 1
- Polarity inversion
- Polarity inversion register · p. 1
- Power-on reset
- Internal · p. 1
- Power-up behavior
- No glitch on power up · p. 1
- Input filtering
- Noise filter on SCL and SDA · p. 1
- Package
- PW, 24-pin TSSOP · p. 3
Around it
4- res not specified
- between INT and VCC; Pull-up resistor for interrupt open-drain output. · p. 3
- res not specified
- between RESET and VCC; Pull-up resistor if no active connection is used. · p. 3
- res not specified
- between SCL and VCC; Serial clock bus pull-up resistor. · p. 4
- res not specified
- between SDA and VCC; Serial data bus pull-up resistor. · p. 4
Specifications
105| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage VCC | Over operating free-air temperature range | min -0.5 · max 6 V | 5 |
| Input voltage VI | Over operating free-air temperature range; see footnote (2) | min -0.5 · max 6 V | 5 |
| Output voltage VO | Over operating free-air temperature range; see footnote (2) | min -0.5 · max 6 V | 5 |
| Input clamp current IIK | VI < 0 | max -20 mA | 5 |
| Output clamp current IOK | VO < 0 | max -20 mA | 5 |
| Input-output clamp current IIOK | VO < 0 or VO > VCC; maximum magnitude ±20 mA | max 20 mA | 5 |
| Continuous output low current IOL | VO = 0 to VCC | max 50 mA | 5 |
| Continuous output high current IOH | VO = 0 to VCC | max -50 mA | 5 |
| Continuous current through GND ICC | max -250 mA | 5 | |
| Continuous current through VCC ICC | max 160 mA | 5 | |
| Maximum junction temperature Tj(MAX) | max 100 °C | 5 | |
| Storage temperature Tstg | min -65 · max 150 °C | 5 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 V | max 2000 V | 5 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1000 V | max 1000 V | 5 |
| Supply voltage VCC | min 1.65 · max 5.5 V | 5 | |
| High-level input voltage VIH | A0, A1, RESET, P07–P00, P10–P17; minimum 0.7 × VCC | max 5.5 V | 5 |
| Low-level input voltage VIL | SCL, SDA, A0, A1, RESET, P07–P00, P10–P17; maximum 0.3 × VCC | min -0.5 V | 5 |
| High-level output current IOH | P07–P00, P17–P10 | max -10 mA | 5 |
| Low-level output current IOL | P00–P07, P10–P17; Tj ≤ 65°C | max 25 mA | 5 |
| Low-level output current IOL | P00–P07, P10–P17; Tj ≤ 85°C | max 18 mA | 5 |
| Low-level output current IOL | P00–P07, P10–P17; Tj ≤ 100°C | max 11 mA | 5 |
| Low-level output current IOL | INT, SDA; Tj ≤ 85°C | max 6 mA | 5 |
| Low-level output current IOL | INT, SDA; Tj ≤ 100°C | max 3.5 mA | 5 |
| Operating free-air temperature TA | min -40 · max 85 °C | 5 | |
| Junction-to-ambient thermal resistance RθJA | PW (TSSOP), 24 PINS | typ 108.8 °C/W | 6 |
| Junction-to-case (top) thermal resistance RθJC(top) | PW (TSSOP), 24 PINS | typ 54 °C/W | 6 |
| Junction-to-board thermal resistance RθJB | PW (TSSOP), 24 PINS | typ 62.8 °C/W | 6 |
| Junction-to-top characterization parameter ψJT | PW (TSSOP), 24 PINS | typ 11.1 °C/W | 6 |
| Junction-to-board characterization parameter ψJB | PW (TSSOP), 24 PINS | typ 62.3 °C/W | 6 |
| Input diode clamp voltage VIK | II = –18 mA; VCC = 1.65 V to 5.5 V | min -1.2 V | 6 |
| Power-on reset voltage, VCC rising VPORR | VI = VCC or GND, IO = 0; VCC = 1.65 V to 5.5 V | typ 1.2 · max 1.5 V | 6 |
| Power-on reset voltage, VCC falling VPORF | VI = VCC or GND, IO = 0; VCC = 1.65 V to 5.5 V | min 0.75 · typ 1 V | 6 |
| P-port high-level output voltage VOH | IOH = –8 mA; VCC = 1.65 V | min 1.2 V | 6 |
| P-port high-level output voltage VOH | IOH = –8 mA; VCC = 2.3 V | min 1.8 V | 6 |
| P-port high-level output voltage VOH | IOH = –8 mA; VCC = 3 V | min 2.6 V | 6 |
| P-port high-level output voltage VOH | IOH = –8 mA; VCC = 4.75 V | min 4.1 V | 6 |
| P-port high-level output voltage VOH | IOH = –10 mA; VCC = 1.65 V | min 1 V | 6 |
| P-port high-level output voltage VOH | IOH = –10 mA; VCC = 2.3 V | min 1.7 V | 6 |
| P-port high-level output voltage VOH | IOH = –10 mA; VCC = 3 V | min 2.5 V | 6 |
| P-port high-level output voltage VOH | IOH = –10 mA; VCC = 4.75 V | min 4 V | 6 |
| SDA IOL | VOL = 0.4 V; VCC = 1.65 V to 5.5 V | min 3 mA | 6 |
| P port IOL | VOL = 0.5 V; VCC = 1.65 V to 5.5 V | min 8 mA | 6 |
| P port IOL | VOL = 0.7 V; VCC = 1.65 V to 5.5 V | min 10 mA | 6 |
| INT IOL | VOL = 0.4 V | min 3 mA | 6 |
| SCL, SDA II | VI = VCC or GND; VCC = 1.65 V to 5.5 V; maximum magnitude ±1 uA | max 1 uA | 6 |
| A0, A1, RESET II | VI = VCC or GND; VCC = 1.65 V to 5.5 V; maximum magnitude ±1 uA | max 1 uA | 6 |
| P port IIH | VI = VCC; VCC = 1.65 V to 5.5 V | max 1 uA | 6 |
| P port IIL | VI = GND; VCC = 1.65 V to 5.5 V | max -1 uA | 6 |
| Operating mode ICC | VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no load; VCC = 5.5 V | typ 22 · max 40 uA | 7 |
| Operating mode ICC | VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no load; VCC = 3.6 V | typ 11 · max 30 uA | 7 |
| Operating mode ICC | VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no load; VCC = 2.7 V | typ 8 · max 19 uA | 7 |
| Operating mode ICC | VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, no load; VCC = 1.95 V | typ 5 · max 11 uA | 7 |
| Standby mode ICC | VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 5.5 V | typ 1.5 · max 3.9 uA | 7 |
| Standby mode ICC | VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 3.6 V | typ 0.9 · max 2.2 uA | 7 |
| Standby mode ICC | VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 2.7 V | typ 0.6 · max 1.8 uA | 7 |
| Standby mode ICC | VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 1.95 V | typ 0.4 · max 1.5 uA | 7 |
| Standby mode ICC | VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 5.5 V | typ 1.5 · max 8.7 uA | 7 |
| Standby mode ICC | VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 3.6 V | typ 0.9 · max 4 uA | 7 |
| Standby mode ICC | VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 2.7 V | typ 0.6 · max 3 uA | 7 |
| Standby mode ICC | VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, no load; VCC = 1.95 V | typ 0.4 · max 2.2 uA | 7 |
| SCL Ci | VI = VCC or GND; VCC = 1.65 V to 5.5 V | typ 3 · max 8 pF | 7 |
| SDA Cio | VIO = VCC or GND; VCC = 1.65 V to 5.5 V | typ 3 · max 9.5 pF | 7 |
| P port Cio | VIO = VCC or GND; VCC = 1.65 V to 5.5 V | typ 3.7 · max 9.5 pF | 7 |
| I2C clock frequency fscl | I2C BUS—STANDARD MODE | min 0 · max 100 kHz | 7 |
| I2C clock high time tsch | I2C BUS—STANDARD MODE | min 4 us | 7 |
| I2C clock low time tscl | I2C BUS—STANDARD MODE | min 4.7 us | 7 |
| I2C spike time tsp | I2C BUS—STANDARD MODE | max 50 ns | 7 |
| I2C serial-data setup time tsds | I2C BUS—STANDARD MODE | min 250 ns | 7 |
| I2C serial-data hold time tsdh | I2C BUS—STANDARD MODE | min 0 ns | 7 |
| I2C input rise time ticr | I2C BUS—STANDARD MODE | max 1000 ns | 7 |
| I2C input fall time ticf | I2C BUS—STANDARD MODE | max 300 ns | 7 |
| I2C output fall time tocf | I2C BUS—STANDARD MODE; 10-pF to 400-pF bus | max 300 ns | 7 |
| I2C bus free time between stop and start tbuf | I2C BUS—STANDARD MODE | min 4.7 us | 7 |
| I2C start or repeated start condition setup tsts | I2C BUS—STANDARD MODE | min 4.7 us | 7 |
| I2C start or repeated start condition hold tsth | I2C BUS—STANDARD MODE | min 4 us | 7 |
| I2C stop condition setup tsps | I2C BUS—STANDARD MODE | min 4 us | 7 |
| Valid data time tvd(data) | I2C BUS—STANDARD MODE; SCL low to SDA output valid | max 3.45 us | 7 |
| Valid data time of ACK condition tvd(ack) | I2C BUS—STANDARD MODE; ACK signal from SCL low to SDA (out) low | max 3.45 us | 7 |
| I2C bus capacitive load Cb | I2C BUS—STANDARD MODE | max 400 pF | 7 |
| I2C clock frequency fscl | I2C BUS—FAST MODE | min 0 · max 400 kHz | 7 |
| I2C clock high time tsch | I2C BUS—FAST MODE | min 0.6 us | 7 |
| I2C clock low time tscl | I2C BUS—FAST MODE | min 1.3 us | 7 |
| I2C spike time tsp | I2C BUS—FAST MODE | max 50 ns | 7 |
| I2C serial-data setup time tsds | I2C BUS—FAST MODE | min 100 ns | 7 |
| I2C serial-data hold time tsdh | I2C BUS—FAST MODE | min 0 ns | 7 |
| I2C input rise time ticr | I2C BUS—FAST MODE | min 20 · max 300 ns | 8 |
| I2C input fall time ticf | I2C BUS—FAST MODE; minimum 20 × (VCC / 5.5 V) ns | max 300 ns | 8 |
| I2C output fall time tocf | I2C BUS—FAST MODE; 10-pF to 400-pF bus; minimum 20 × (VCC / 5.5 V) ns | max 300 ns | 8 |
| I2C bus free time between stop and start tbuf | I2C BUS—FAST MODE | min 1.3 us | 8 |
| I2C start or repeated start condition setup tsts | I2C BUS—FAST MODE | min 0.6 us | 8 |
| I2C start or repeated start condition hold tsth | I2C BUS—FAST MODE | min 0.6 us | 8 |
| I2C stop condition setup tsps | I2C BUS—FAST MODE | min 0.6 us | 8 |
| Valid data time tvd(data) | I2C BUS—FAST MODE; SCL low to SDA output valid | max 0.9 us | 8 |
| Valid data time of ACK condition tvd(ack) | I2C BUS—FAST MODE; ACK signal from SCL low to SDA (out) low | max 0.9 us | 8 |
| I2C bus capacitive load Cb | I2C BUS—FAST MODE | max 400 pF | 8 |
| Reset pulse duration tW | Over recommended operating free-air temperature range | min 6 ns | 8 |
| Reset recovery time tREC | Over recommended operating free-air temperature range | min 0 ns | 8 |
| Time to reset tRESET | VCC = 2.3 V - 5.5 V | min 400 ns | 8 |
| Time to reset tRESET | VCC = 1.65 V - 2.3 V | min 550 ns | 8 |
| Interrupt valid time tiv | P port to INT; CL ≤ 100 pF; over recommended operating free-air temperature range | max 4 us | 8 |
| Interrupt reset delay time tir | SCL to INT; CL ≤ 100 pF; over recommended operating free-air temperature range | max 4 us | 8 |
| Output data valid tpv | VCC = 2.3 V - 5.5 V; SCL to P port; CL ≤ 100 pF | max 200 ns | 8 |
| Output data valid tpv | VCC = 1.65 V - 2.3 V; SCL to P port; CL ≤ 100 pF | max 300 ns | 8 |
| Input data setup time tps | P port to SCL; CL ≤ 100 pF; over recommended operating free-air temperature range | min 150 ns | 8 |
| Input data hold time tph | P port to SCL; CL ≤ 100 pF; over recommended operating free-air temperature range | min 1 us | 8 |
Pins, by the datasheet
24- 1 INT
- Interrupt open-drain output. Connect to VCC through a pull-up resistor. · p. 3
- 2 A1
- Address input. Connect directly to VCC or ground. · p. 3
- 3 RESET
- Active-low reset input. Connect to VCC through a pull-up resistor if no active connection is used. · p. 3
- 4 P00
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 5 P01
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 6 P02
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 7 P03
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 8 P04
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 9 P05
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 10 P06
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 11 P07
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 12 GND
- Ground. · p. 3
- 13 P10
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 14 P11
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 15 P12
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 16 P13
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 17 P14
- Push-pull P-port input-output; configured as an input at power on. · p. 3
- 18 P15
- Push-pull P-port input-output; configured as an input at power on. · p. 4
- 19 P16
- Push-pull P-port input-output; configured as an input at power on. · p. 4
- 20 P17
- Push-pull P-port input-output; configured as an input at power on. · p. 4
- 21 A0
- Address input. Connect directly to VCC or ground. · p. 3
- 22 SCL
- Serial clock bus. Connect to VCC through a pull-up resistor. · p. 4
- 23 SDA
- Serial data bus. Connect to VCC through a pull-up resistor. · p. 4
- 24 VCC
- Supply voltage. · p. 4
Parts like it
8PCA9555PW
TSSOP-24-40℃~+85℃ 1.1uA 16 2.3V~5.5V 3mA 400kHz 8 I2C、SMBus Interrupt Output Reset function、Cascade and address expansion TSSOP-24 I/O Expanders ROHSNXP SemiconductorsI/O ExpandersTCA9535PW
TSSOP-24-40℃~+85℃ 1.5uA 1.65V~5.5V 10mA 16 25mA 400kHz 4V 8 I2C、SMBus Interrupt Output Push-Pull Reset function、Cascade and address expansion、Built-in LED driver TSSOP-24 I/O Expanders ROHSTexas InstrumentsI/O ExpandersTCA9555PW
TSSOP-24-40℃~+85℃ 1.65V~5.5V 10mA 16 25mA 3.5uA 400kHz 4V 500mV 8 I2C、SMBus Interrupt Output Push-Pull Reset function、Cascading and address extension、Built-in LED driver TSSOP-24 I/O Expanders ROHSTexas InstrumentsI/O ExpandersPCA9539PW
TSSOP-24-40℃~+85℃ 16 1uA 2.3V~5.5V 4 400kHz I2C、SMBus Interrupt Output Reset function、Cascading and address extension TSSOP-24 I/O Expanders ROHSNXP SemiconductorsI/O ExpandersPCA9535PW
TSSOP-24-40℃~+85℃ 10mA 16 2.3V~5.5V 250nA 400kHz 8 I2C、SMBus Interrupt Output Push-Pull Reset function、Cascading and address extension TSSOP-24 I/O Expanders ROHSNXP SemiconductorsI/O ExpandersPCA9555APW
TSSOP-24-40℃~+85℃ 1.5uA 1.65V~5.5V 16 200mV 25mA 400kHz 8 I2C、SMBus Interrupt Output Reset function、Cascading and address extension、Built-in LED driver TSSOP-24 I/O Expanders ROHSNXP SemiconductorsI/O ExpandersNCA9535PW-Q100J
TSSOP-24Reset function、Cascading and address extension、Built-in LED driver TSSOP-24 I/O Expanders ROHSNexperiaI/O ExpandersNCA9555PWJ
TSSOP-24I/O ExpandersNexperia
Questions
Is there a KiCad symbol and footprint for the TCA9539PW?
Yes. The symbol is Analog & Interface:TCA9539PWR and the footprint Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TCA9539PW?
TSSOP-24, with 24 pins. Its footprint is drawn on this page.
Where is the TCA9539PW datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TCA9539PW?
JLCPCB lists it as part C131972, with 8,429 in stock; the sellers' links on this page open their listings.
What can replace the TCA9539PW?
Parts like it in the library: the PCA9555PW by NXP Semiconductors, the TCA9535PW by Texas Instruments, the TCA9555PW by Texas Instruments and the PCA9539PW by NXP Semiconductors. Check their datasheets: a part that fits the footprint may still differ in its ratings.