Skip to the content
123456789

DRV8251ADDA

Texas InstrumentsExtended

SOPowerPAD-8 Brushed DC Motor Drivers ROHS

Part id
ti/DRV8251ADDA
Category
Brushed DC Motor Drivers
Package
SOPowerPAD-8
Pins
9
In stock
22,875 at JLCPCB (C5218844)
Used on
8 open-source boards

Overview

The DRV8251ADDA is a brushed DC Motor Driver made by Texas Instruments in a SOPowerPAD-8 package with 9 pins. SOPowerPAD-8 Brushed DC Motor Drivers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:DRV8251ADDAR, from EasyEDA) and its footprint (EasyEDA_Cloud:SOPOWERPAD-8_L4.9-W3.9-P1.27-LS6.0-TL-EP, from EasyEDA), ready for a KiCad board. 22,875 are in stock at JLCPCB (part C5218844). 8 open-source boards in 6 repositories on GitHub use it.

Symbol

1IPROPI2IN23IN14VREF5VM6OUT17GND8OUT29PAD
EasyEDA_Cloud:DRV8251ADDARFrom EasyEDA

Footprint

123456789
EasyEDA_Cloud:SOPOWERPAD-8_L4.9-W3.9-P1.27-LS6.0-TL-EPFrom EasyEDA

From the datasheet

13
Supply, least
4.5 V · VM, recommended operating min · p. 4
Supply, most
48 V · VM, recommended operating max · p. 4
Supply, absolute maximum
50 V · VM, absolute maximum · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 4
Works up to
125 °C · Operating ambient temperature max · p. 4
Junction, hottest
150 °C · Operating junction temperature max · p. 4
Takes working
3 mA · VM active mode typical, VVM = 24 V, IN1 = IN2 = 1 · p. 5
Takes at most
4 mA · VM active mode max, VVM = 24 V, IN1 = IN2 = 1 · p. 5
Takes asleep
1 µA · VM sleep mode max, VVM = 24 V, IN1 = IN2 = 0, TJ = 25°C · p. 5
Junction to air (DDA (HSOP))
40.4 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to board (DDA (HSOP))
14.4 K/W · Junction-to-board thermal resistance · p. 5
Junction to case (DDA (HSOP))
54.7 K/W · Junction-to-case (top) thermal resistance · p. 5
Edge
220 ns · Output rise time typical, VVM = 24 V, 10% to 90% · p. 5

What it is and has

9
Driver
N-channel H-bridge brushed DC motor driver · p. 1
Peak output current
4.1 A · p. 1
Control interface
PWM · p. 1
Logic input compatibility
1.8 V, 3.3 V, and 5 V · p. 1
Low-power mode
Sleep · p. 1
Package
8-Pin HSOP with PowerPAD, 4.9 × 6.0 mm · p. 1
Protection
VM undervoltage lockout (UVLO) · p. 1
Protection
Auto-retry overcurrent protection (OCP) · p. 1
Protection
Thermal shutdown (TSD) · p. 1

Around it

2
cap 0.1-µF
between VM and GND; CVM1; low ESR ceramic capacitor, VM-rated. · p. 10
cap Not specified
between VM and GND; CVM2; VM-rated bulk capacitance; table refers to Section 10.1. · p. 10

Specifications

52
ParameterConditionsAs printedPage
Power supply pin voltageVMmin -0.3 · max 50 V4
Power supply transient voltage rampVMmin 0 · max 2 V/us4
Logic pin voltageINxmin -0.3 · max 7 V4
Reference input pin voltageVREFmin -0.3 · max 6 V4
Output pin voltageOUTx; maximum VM + 0.7 Vmin -0.7 V4
Current sense input pin voltageIPROPImin -0.3 · max 5.75 V4
Ambient temperature TAmin -40 · max 125 °C4
Junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±6000 Vmax 6000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; ±750 Vmax 750 V4
Power supply voltage VVMVMmin 4.5 · max 48 V4
Reference voltage VVREFVREFmin 0 · max 3.6 V4
Logic input voltage VININxmin 0 · max 5.5 V4
PWM frequency fPWMINxmin 0 · max 200 kHz4
Peak output current IOUTOUTx; 4.5 ≤ VVM < 5.5 V; power dissipation and thermal limits must be observedmin 0 · max 3.7 A4
Peak output current IOUTOUTx; VVM ≥ 5.5 V; power dissipation and thermal limits must be observedmin 0 · max 4.1 A4
Peak output current IIPROPIIPROPImin 0 · max 3 mA4
Operating ambient temperature TAmin -40 · max 125 °C4
Operating junction temperature TJmin -40 · max 150 °C4
Junction-to-ambient thermal resistance RθJADRV8251A, DDA (HSOP), 8 PINStyp 40.4 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DRV8251A, DDA (HSOP), 8 PINStyp 54.7 °C/W5
Junction-to-board thermal resistance RθJBDRV8251A, DDA (HSOP), 8 PINStyp 14.4 °C/W5
Junction-to-top characterization parameter ΨJTDRV8251A, DDA (HSOP), 8 PINStyp 4.1 °C/W5
Junction-to-board characterization parameter ΨJBDRV8251A, DDA (HSOP), 8 PINStyp 14.4 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV8251A, DDA (HSOP), 8 PINStyp 4.2 °C/W5
VM sleep mode current IVMQVVM = 24 V, IN1 = IN2 = 0, TJ = 25°Cmax 1 uA5
VM active mode current IVMVVM = 24 V, IN1 = IN2 = 1typ 3 · max 4 mA5
Turnon time tWAKEControl signal to active modemax 250 us5
Turnoff time tSLEEPControl signal to sleep modemin 0.8 · max 1.5 ms5
Input logic low voltage VILmax 0.5 V5
Input logic high voltage VIHmin 1.5 V5
Input hysteresis VHYStyp 200 mV5
Input logic low current IILVIN = 0 Vmin -1 · max 1 uA5
Input logic high current IIHVIN = 3.3 Vtyp 33 · max 100 uA5
Input pulldown resistance RPDTo GNDtyp 100 kΩ5
High-side MOSFET on resistance RDS(on)_HSVVM = 24 V, I = 1 A, fPWM = 25 kHztyp 225 mΩ5
Low-side MOSFET on resistance RDS(on)_LSVVM = 24 V, I = 1 A, fPWM = 25 kHztyp 225 mΩ5
Body diode forward voltage VSDIOUT = 1 Atyp 0.8 V5
Output rise time tRISEVVM = 24 V, OUTx rising from 10% to 90%typ 220 ns5
Output fall time tFALLVVM = 24 V, OUTx falling from 90% to 10%typ 220 ns5
Input to output propagation delay tPDINx to OUTxtyp 0.7 · max 1 us5
Output dead time tDEADtyp 200 ns5
Current mirror scaling factor AIPROPItyp 1575 uA/A5
Current mirror total error AERRIOUT = 1.5 A, VVM ≥ 6.5 V, VIPROPI ≤ 3.0 Vmin -5 · max 5 %5
Current regulation off time tOFFtyp 25 us5
Current regulation blanking time tBLKtyp 1.4 us5
Current sense delay time tDELAYtyp 1.1 us5
Current regulation deglitch time tDEGtyp 0.7 us5
Supply undervoltage lockout (UVLO) VUVLOSupply risingmin 4.15 · typ 4.3 · max 4.45 V5
Supply undervoltage lockout (UVLO) VUVLOSupply fallingmin 4.05 · typ 4.2 · max 4.35 V5
Supply UVLO hysteresis VUVLO_HYSRising to falling thresholdtyp 100 mV5

Pins, by the datasheet

9
1 IPROPI
Analog current output proportional to load current. · p. 3
2 IN2
Logic input controlling the H-bridge output; has an internal pulldown. · p. 3
3 IN1
Logic input controlling the H-bridge output; has an internal pulldown. · p. 3
4 VREF
Analog input for current regulation; the pin description says to apply 0 to 5 V. · p. 3
5 VM
4.5-V to 48-V power supply; connect a 0.1-uF bypass capacitor and sufficient VM-rated bulk capacitance to ground. · p. 3
6 OUT1
H-bridge output; connect directly to the motor or other inductive load. · p. 3
7 GND
Device power ground; connect to system ground. · p. 3
8 OUT2
H-bridge output; connect directly to the motor or other inductive load. · p. 3
PAD PAD
Connect to board ground using large ground planes on multiple layers and multiple nearby vias for thermal dissipation. · p. 3

Ordering codes, by the datasheet

1
DRV8251ADDA
HSOP (8) · 4.90 mm × 6.00 mm nominal body size · p. 1

Open-source boards using it

8
  • 2 layers82 × 56 mmRipplecounter, the printed circuit board in 3D

    Ripplecounter

    jackw01/ripplecounter

    Sensorless brushed DC motor position control with Raspberry Pi Pico

    126 parts15
  • 2 layers64 × 69.9 mmControl board, the printed circuit board in 3D

    Control board

    luckymuniza/spinkovacka

    64 parts
  • 2 layers65 × 56 mmFYDP, the printed circuit board in 3D

    FYDP

    Michael-Done/FYDP_ELEC

    Electrical schematic and layout for capstone design project.

    43 parts
  • 2 layers90 × 108 mmG5500-pidrive, the printed circuit board in 3D

    G5500-pidrive

    philcrump/g5500-pidrive

    Driving an AC Yaesu G-5500 Az+El with DC-source PWM from a Raspberry Pi.

    106 partsMIT
  • 4 layers100 × 100 mmAmod m, the printed circuit board in 3D

    Amod m

    gallicchio/AMOD-and-RFMOD

    The tutorial's 2x12 adapter (/mudd/133electronics/icepi-zero-dac-adc/adapterboard/) with a 2 x 6 right-angle Pmod socket on a 15 mm extension of its right-hand end, so an Icepi Zero can drive AMOD-A's and RF-MOD's Pmod…

    207 parts
  • 2 layers64 × 69.9 mmControl board, the printed circuit board in 3D

    Control board

    luckymuniza/spinkovacka

    49 parts
  • 4 layers57.8 × 80 mmArm drive, the printed circuit board in 3D

    Arm drive

    robotique-udes/PCB

    69 partsMIT

Questions

Is there a KiCad symbol and footprint for the DRV8251ADDA?

Yes. The symbol is EasyEDA_Cloud:DRV8251ADDAR and the footprint EasyEDA_Cloud:SOPOWERPAD-8_L4.9-W3.9-P1.27-LS6.0-TL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV8251ADDA?

SOPowerPAD-8, with 9 pins. Its footprint is drawn on this page.

Where is the DRV8251ADDA datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV8251ADDA?

JLCPCB lists it as part C5218844, with 22,875 in stock; the sellers' links on this page open their listings.

Which open-source boards use the DRV8251ADDA?

8 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.