Skip to the content
12345

LD3985M33R

STMicroelectronicsExtended

-40℃~+125℃@(Tj) 1 150mA 150uA 3.3V 30uVrms 50dB@(10kHz) 60mV@(150mA) 6V Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
st/LD3985M33R
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
SOT-23-5L
Pins
5
In stock
3,059 at JLCPCB (C46243)
Used on
15 open-source boards

Overview

The LD3985M33R is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by STMicroelectronics in a SOT-23-5L package with 5 pins. -40℃~+125℃@(Tj) 1 150mA 150uA 3.3V 30uVrms 50dB@(10kHz) 60mV@(150mA) 6V Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulators:LD3985MxxR, from CERN's library) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 3,059 are in stock at JLCPCB (part C46243). 15 open-source boards in 14 repositories on GitHub use it.

Symbol

1VIN3INH4NC5VOUT2GND
Regulators:LD3985MxxRFrom CERN's library

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

14
Supply, least
2.5 V · VI, recommended operating min · p. 7
Supply, most
6 V · VI, recommended operating max · p. 7
Supply, absolute maximum
6 V · VI, absolute max DC input voltage · p. 6
Junction, hottest
125 °C · Operating junction temperature max · p. 6
Takes working
170 µA · Quiescent current typical, ON mode, IO = 0 to 150 mA · p. 7
Takes asleep
3 nA · OFF mode quiescent current typical, VINH = 0.4 V · p. 7
Gives
150 mA · Guaranteed output current max · p. 1
Current limit
600 mA · Short-circuit current typical, RL = 0 · p. 7
Output
3.3 V · LD3985M33R fixed nominal output · p. 20
Dropout
20 mV · Dropout typical at IO = 50 mA · p. 7
Dropout
45 mV · Dropout typical at IO = 100 mA · p. 7
Dropout
60 mV · Dropout typical at IO = 150 mA · p. 7
Junction to case (SOT23-5L/TSOT23)
81 K/W · Thermal resistance junction-case · p. 6
Junction to air (SOT23-5L/TSOT23)
255 K/W · Thermal resistance junction-ambient · p. 6

What it is and has

4
Protection
Internal current and thermal limit · p. 1
Capacitor compatibility
Stable with low ESR ceramic capacitors · p. 1
Shutdown
Logic-controlled electronic shutdown · p. 1
Supply voltage rejection
60 dB at 1 kHz, 50 dB at 10 kHz · p. 1

Specifications

38
ParameterConditionsAs printedPage
DC input voltage VImin -0.3 · max 6 V6
DC output voltage VOUpper limit VI+0.3 Vmin -0.3 V6
Inhibit input voltage VINHUpper limit VI+0.3 Vmin -0.3 V6
Storage temperature range TSTGmin -65 · max 150 °C6
Operating junction temperature range TOPmin -40 · max 125 °C6
Thermal resistance junction-case RthJCSOT23-5L/TSOT23max 81 °C/W6
Thermal resistance junction-ambient RthJASOT23-5L/TSOT23max 255 °C/W6
Operating input voltage VImin 2.5 · max 6 V7
Output voltage accuracy, VO(NOM) ≥ 2.5V VOIO = 1 mAmin -2 · max 2 % of VO(NOM)7
Output voltage accuracy, VO(NOM) ≥ 2.5V VOTJ= -40 to 125 °Cmin -3 · max 3 % of VO(NOM)7
Line regulation ΔVOVI = VO(NOM) + 0.5 to 6 V; TJ = -40 to 125 °Cmin -0.1 · max 0.1 %/V7
Load regulation ΔVOIO = 1 mA to 150mA, TJ = -40 to 125°C; SOT23-5L/TSOT23-5L; VO(NOM) ≥ 2.5 Vtyp 0.0025 · max 0.005 %/mA7
Output AC line regulation ΔVOVI = VO(NOM) + 1 V, IO = 150 mA, tR= tF = 30 ustyp 1.5 mVPP7
Quiescent current IQON mode: VINH = 1.2 V; IO = 0typ 85 uA7
Quiescent current IQON mode: VINH = 1.2 V; IO = 0, TJ= -40 to 125 °Cmax 150 uA7
Quiescent current IQON mode: VINH = 1.2 V; IO = 0 to 150 mAtyp 170 uA7
Quiescent current IQON mode: VINH = 1.2 V; IO = 0 to 150 mA, TJ= -40 to 125 °Cmax 250 uA7
Quiescent current IQOFF mode: VINH = 0.4 Vtyp 0.003 uA7
Quiescent current IQOFF mode: VINH = 0.4 V; TJ= -40 to 125 °Cmax 1.5 uA7
Dropout voltage VDROPIO = 1 mAtyp 0.4 mV7
Dropout voltage VDROPIO = 1 mA, TJ= -40 to 125 °Cmax 2 mV7
Dropout voltage VDROPIO = 50 mAtyp 20 mV7
Dropout voltage VDROPIO = 50 mA, TJ= -40 to 125 °Cmax 35 mV7
Dropout voltage VDROPIO = 100 mAtyp 45 mV7
Dropout voltage VDROPIO = 100 mA, TJ= -40 to 125 °Cmax 70 mV7
Dropout voltage VDROPIO = 150 mAtyp 60 mV7
Dropout voltage VDROPIO = 150 mA, TJ= -40 to 125 °Cmax 100 mV7
Short-circuit current ISCRL = 0typ 600 mA7
Supply voltage rejection SVRVI = VO(NOM)+0.25 V ± VRIPPLE = 0.1 V, IO= 50 mA; f = 1kHztyp 60 dB8
Supply voltage rejection SVRVI = VO(NOM)+0.25 V ± VRIPPLE = 0.1 V, IO= 50 mA; f = 10kHztyp 50 dB8
Inhibit input logic low VINHVI = 2.5 V to 6 V, TJ= -40 to 125 °Cmax 0.4 V8
Inhibit input logic high VINHVI = 2.5 V to 6 V, TJ= -40 to 125 °Cmin 1.2 V8
Inhibit input current IINHVINH = 0.4 V, VI = 6 V; typical ±1 nAtyp 1 nA8
Output noise voltage eNBW = 10 Hz to 100 kHz, CO = 1 uFtyp 30 uVRMS8
Turn-on time tONCBYP = 10 nFtyp 100 · max 250 us8
Thermal shutdown TSHDNtyp 160 °C8
Output capacitor COCapacitancemin 1 · max 22 uF8
Output capacitor COESRmin 5 · max 5000 mΩ8

Pins, by the datasheet

5
1 VI
Input voltage of the LDO. · p. 4
2 GND
Common ground. · p. 4
3 VINH
Inhibit input: ON at VINH ≥ 1.2 V, OFF at VINH ≤ 0.4 V; do not leave floating, no internal pull-down or pull-up. · p. 4
4 BYPASS
Connect an external capacitor, usually 10 nF, to minimize noise voltage. · p. 4
5 VO
Output voltage of the LDO. · p. 4

Ordering codes, by the datasheet

1
LD3985M33R
SOT23-5L · 3.3 V output · p. 20

Open-source boards using it

15See all 15
  • 2 layers42.5 × 21 mmPS2USB, the printed circuit board in 3D

    PS2USB

    meerstern/PS2USB_CONVERTER

    PS/2 USB CONVERTER for old computers with USB keyboard

    25 parts9
  • 2 layers60 × 60 mmProjectionball, the printed circuit board in 3D

    Projectionball

    meerstern/ProjectionBallUnit

    ProjectionBall v7.x with RP2040

    76 parts7
  • 4 layers58 × 58 mmRgb matrix, the printed circuit board in 3D

    Rgb matrix

    joh/rgb-matrix

    RGB Matrix with USB and 48-bit colors!

    138 parts3
  • 2 layers22 × 26.4 mmConverter, the printed circuit board in 3D

    Converter

    meerstern/USBSerial_I2C_Converter

    USBSerial I2C Converter

    26 parts3
  • 2 layers45 × 45 mmFlight ctrl v2, the printed circuit board in 3D

    Flight ctrl v2

    MickAvery/flight-controller-design

    Design of my flight controller using KiCAD

    50 parts1
  • 2 layers99.1 × 95.3 mmTmb musicplayer, the printed circuit board in 3D

    Tmb musicplayer

    janfietz/tmb_board

    Hardware design for toddlerMusicBox project

    203 partsCC-BY-SA-4.0
  • 4 layers40 × 49 mmADC, the printed circuit board in 3D

    ADC

    maknoll/MRI_ADC_Probe

    This repository includes all hard- firm- and software resources realated to MRI ADC Probe developed for measuring gradient fields in a running MRI scanner.

    69 parts
  • 2 layers23.9 × 19.8 mm.watch, the printed circuit board in 3D

    .watch

    silardg/.watch

    PCB for a small watch

    28 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the LD3985M33R?

Yes. The symbol is Regulators:LD3985MxxR and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LD3985M33R?

SOT-23-5L, with 5 pins. Its footprint is drawn on this page.

Where is the LD3985M33R datasheet?

STMicroelectronics publishes it: the Datasheet link on this page opens it.

Where can I order the LD3985M33R?

JLCPCB lists it as part C46243, with 3,059 in stock; the sellers' links on this page open their listings.

What can replace the LD3985M33R?

Parts like it in the library: the ME6211C33M5G-N by MICRONE, the SPX3819M5-L-3-3/TR by MaxLinear, the RT9013-33GB by RICHTEK and the XC6219B332MR by UMW. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the LD3985M33R?

15 boards in 14 repositories on GitHub; the most starred are listed on this page, with their KiCad files.