Skip to the content
17

RFX2401C

Skyworks SolutionsExtended

-10dB -12dB -15dB -40℃~+85℃ -8dB -8dBm 2.4GHz~2.5GHz 22dBm 2V~3.6V ZigBee 集成低噪声放大器、集成射频开关、集成功率放大器、集成射频滤波器、集成功率检测器 QFN-16-EP(3x3) RF Front End Circuits ROHS

Part id
skyworks/RFX2401C
Category
RF Front End Circuits
Package
QFN-16-EP(3x3)
Pins
17
In stock
42,295 at JLCPCB (C19213)
Used on
28 open-source boards

Overview

The RFX2401C is a RF Front End Circuit made by Skyworks Solutions in a QFN-16-EP(3x3) package with 17 pins. -10dB -12dB -15dB -40℃~+85℃ -8dB -8dBm 2.4GHz~2.5GHz 22dBm 2V~3.6V ZigBee 集成低噪声放大器、集成射频开关、集成功率放大器、集成射频滤波器、集成功率检测器 QFN-16-EP(3x3) RF Front End Circuits ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:RFX2401C, from EasyEDA) and its footprint (EasyEDA_Cloud:QFN-16_L3.0-W3.0-P0.50-BL-EP1.7, from EasyEDA), ready for a KiCad board. 42,295 are in stock at JLCPCB (part C19213). 28 open-source boards in 26 repositories on GitHub use it.

Symbol

1GND2GND3GND4TXRX5TXEN6RXEN7GND8GND9GND10ANT11GND12GND13DNC14VDD15GND16VDD17EP
EasyEDA_Cloud:RFX2401CFrom EasyEDA

Footprint

17
EasyEDA_Cloud:QFN-16_L3.0-W3.0-P0.50-BL-EP1.7From EasyEDA

From the datasheet

8
Supply, least
2 V · VDD, recommended operating min, all VDD pins · p. 3
Supply, most
3.6 V · VDD, recommended operating max, all VDD pins · p. 3
Supply, absolute maximum
4 V · VDD, absolute max · p. 3
Works from
-40 °C · Operating ambient temperature min · p. 3
Works up to
85 °C · Operating ambient temperature max · p. 3
Takes working
10 mA · RX quiescent current typical, VDD=3.3V, T=+25 °C, no RF applied · p. 4
Takes at most
100 mA · TX high power current typical, POUT=+20dBm, VDD=3.3V, T=+25 °C · p. 4
Takes asleep
1 µA · DC shutdown current max · p. 5

What it is and has

4
Low noise amplifier
Integrated · p. 1
Transmit / receive switch
Integrated · p. 1
Control logic
Low voltage (1.2V) CMOS · p. 1
Supply decoupling
Internal RF decoupling on all VDD bias pins · p. 1

Around it

2
res 1KΩ
between Transceiver TXEN and TXEN; Series control resistor shown in application circuit. · p. 6
res 1KΩ
between Transceiver RXEN and RXEN; Series control resistor shown in application circuit. · p. 6

Specifications

34
ParameterConditionsAs printedPage
DC VDD Voltage Supplymin 0 · max 4 V3
DC Control Pin VoltageThrough 1Kohm resistormin 0 · max 3.6 V3
DC VDD Current ConsumptionThrough VDD Pins when TX is “ON”max 350 mA3
DC Control Pin Current Consumptionmax 1 uA3
TX RF Input PowerAll Operating Modesmax 5 dBm3
ANT RF Input PowerWhen RX is “ON”max 5 dBm3
Storage Ambient TemperatureNo RF and DC Voltages Applied; Appropriate care required according to JEDEC Standardsmin -50 · max 125 °C3
DC VDD Voltage SupplyAll VDD Pinsmin 2 · typ 3.3 · max 3.6 V3
Control Voltage “High”Through 1Kohm resistor; maximum VDDmin 1.2 V3
Control Voltage “Low”min 0 · max 0.3 V3
Operating Ambient Temperaturemin -40 · max 85 °C3
Operating Frequency BandVDD=3.3V; T=+25 °C; All RF Pins Terminated by 50 Ohmmin 2.4 · max 2.525 GHz4
Saturated Output PowerVDD=3.3V; T=+25 °Ctyp 22 dBm4
Small-Signal GainVDD=3.3V; T=+25 °Ctyp 25 dB4
Second HarmonicVDD=3.3V; T=+25 °C; POUT = +20dBm, IEEE 802.15.4 OQPSK modulation signaltyp -15 dBm/MHz4
Third HarmonicVDD=3.3V; T=+25 °C; POUT = +20dBm, IEEE 802.15.4 OQPSK modulation signaltyp -20 dBm/MHz4
Input Return LossVDD=3.3V; T=+25 °Ctyp -10 dB4
Output Return LossVDD=3.3V; T=+25 °Ctyp -8 dB4
Input / Output Impedance Single-EndedVDD=3.3V; T=+25 °Ctyp 50 Ohm4
TX Quiescent CurrentVDD=3.3V; T=+25 °C; No RF Appliedtyp 17 mA4
TX High Power CurrentVDD=3.3V; T=+25 °C; POUT = +20dBmtyp 100 mA4
GainVDD=3.3V; T=+25 °Ctyp 12 dB4
Noise FigureVDD=3.3V; T=+25 °Ctyp 2.5 dB4
Input Return LossVDD=3.3V; T=+25 °Ctyp -12 dB4
Output Return LossVDD=3.3V; T=+25 °Ctyp -15 dB4
RF Port ImpedanceVDD=3.3V; T=+25 °Ctyp 50 Ohm4
RX Quiescent CurrentVDD=3.3V; T=+25 °C; No RF Appliedtyp 10 mA4
Input P1dBVDD=3.3V; T=+25 °C; At ANT Pintyp -8 dBm4
DC Shutdown Currentmax 1 uA5
TXRX-ANT Insertion Loss (S21) S21Pin < -20dBmtyp -50 dB5
ANT-TXRX Insertion Loss (S21) S21typ -50 dB5
Return Loss (S11) S11From TXRX Porttyp -1.5 dB5
Transmit-Receive Switching Timetyp 800 nsec5
Shut-Down and “ON” State Switching Timetyp 800 nsec5

Pins, by the datasheet

17
1 GND
Must be connected to ground in the application circuit. · p. 2
2 GND
Must be connected to ground in the application circuit. · p. 2
3 GND
Must be connected to ground in the application circuit. · p. 2
4 TXRX
RF signal to/from the transceiver; DC shorted to GND. · p. 2
5 TXEN
CMOS input to control TX enable. · p. 2
6 RXEN
CMOS input to control RX enable. · p. 2
7 GND
Must be connected to ground in the application circuit. · p. 2
8 GND
Must be connected to ground in the application circuit. · p. 2
9 GND
Must be connected to ground in the application circuit. · p. 2
10 ANT
RF signal from the PA or applied to the LNA; DC shorted to GND. · p. 2
11 GND
Must be connected to ground in the application circuit. · p. 2
12 GND
Must be connected to ground in the application circuit. · p. 2
13 DNC
Reserved; do not connect in the application circuit. · p. 2
14 VDD
Alternative supply pin, internally connected to pin 16; no connection needed. · p. 2
15 GND
Must be connected to ground in the application circuit. · p. 2
16 VDD
Voltage supply connection. · p. 2
17 GND
Must be connected to ground in the application circuit. · p. 2

Open-source boards using it

28See all 28
  • 6 layers64.2 × 17.3 mmOpenRX panel rev2.2, the printed circuit board in 3D

    OpenRX panel rev2.2

    OpenDrone-hw/OpenRX

    OpenRX open-source ExpressLRS receiver family hub; board sources live in four dedicated hardware repositories.

    254 parts489CERN-OHL-S-2.0
  • 4 layers37.7 × 37.7 mmDual radio pcb, the printed circuit board in 3D

    Dual radio pcb

    AnyLeaf/elrs-hardware

    This repo contains open source hardware information for AnyLeaf ELRS receivers

    68 parts66MIT
  • 6 layers17 × 15.7 mmOpenRX Gemini, the printed circuit board in 3D

    OpenRX Gemini

    OpenDrone-hw/OpenRX-Gemini

    Open-source dual-radio, dual-band ExpressLRS receiver for Gemini and Xrossband.

    86 parts11CERN-OHL-S-2.0
  • 6 layers39.5 × 39.5 mmTD1 2.4G, the printed circuit board in 3D

    TD1 2.4G

    Paschalis/UAV-TelemetryLink

    Receiver and transmitter solution for GCS using ELRS, mLRS, and MAVLink for reliable telemetry and control.

    63 parts11MIT
  • 8 layers38 × 38 mmKolibri v0.5, the printed circuit board in 3D

    Kolibri v0.5

    bastian2001/Kolibri-FC-Hardware

    Hardware for the Kolibri Flight Controller. 30mm/20mm FC with RP2350 + ELRS onboard

    221 parts8GPL-3.0
  • 6 layers10 × 17.3 mmOpenRX Mono, the printed circuit board in 3D

    OpenRX Mono

    OpenDrone-hw/OpenRX-Mono

    Open-source dual-band ExpressLRS receiver with one LR1121 radio and one U.FL antenna.

    62 parts6CERN-OHL-S-2.0
  • 2 layers43 × 43 mmEsp8266-cc2530, the printed circuit board in 3D

    Esp8266-cc2530

    willg/esp8266-cc2530

    RFX2401C Mode Truth Table: | TXEN | RXEN | Mode | | --- | --- | --- | | 1 | X | TX Active | 0 | 1 | RX Active | 0 | 0 | Chip shutdown

    36 parts6
  • 6 layers63.5 × 50.8 mmNavigation Board, the printed circuit board in 3D

    Navigation Board

    LouisVizard/NavBoard

    A full navigation solution featuring MCU, GNSS receiver, RF transceiver, and 9-DOF IMU

    136 parts2

Parts like it

5

Questions

Is there a KiCad symbol and footprint for the RFX2401C?

Yes. The symbol is EasyEDA_Cloud:RFX2401C and the footprint EasyEDA_Cloud:QFN-16_L3.0-W3.0-P0.50-BL-EP1.7, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the RFX2401C?

QFN-16-EP(3x3), with 17 pins. Its footprint is drawn on this page.

Where is the RFX2401C datasheet?

Skyworks Solutions publishes it: the Datasheet link on this page opens it.

Where can I order the RFX2401C?

JLCPCB lists it as part C19213, with 42,295 in stock; the sellers' links on this page open their listings.

What can replace the RFX2401C?

Parts like it in the library: the RFX2401C(TOKMAS) by Tokmas, the CC2595RGT by Texas Instruments, the LX5584ALQ-TR by Microchip Technology and the AT2401C by ZHONGKEWEI. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the RFX2401C?

28 boards in 26 repositories on GitHub; the most starred are listed on this page, with their KiCad files.