Skip to the content
1234567891011121314151617181920

ATTINY1616-SN

Microchip TechnologyExtended

-40℃~+105℃ 1.8V~5.5V 16KB 18 20MHz 256Byte 2KB 8 Bit AVR Built-in FLASH SOIC-20-300mil Microcontrollers (MCU/MPU/SOC) ROHS

Part id
microchip/ATTINY1616-SN
Category
Microcontrollers (MCU, MPU, SOC)
Package
SOIC-20-300mil
Pins
20
In stock
368 at JLCPCB (C609652)
Used on
27 open-source boards

Overview

The ATTINY1616-SN is a microcontroller made by Microchip Technology in a SOIC-20-300mil package with 20 pins. -40℃~+105℃ 1.8V~5.5V 16KB 18 20MHz 256Byte 2KB 8 Bit AVR Built-in FLASH SOIC-20-300mil Microcontrollers (MCU/MPU/SOC) ROHS.

PCBKit's library has its KiCad symbol (MCU_Microchip_ATtiny:ATtiny1616-S, from KiCad's library) and its footprint (Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm, from KiCad's library), ready for a KiCad board. 368 are in stock at JLCPCB (part C609652). 27 open-source boards in 21 repositories on GitHub use it.

Symbol

1VCC2PA43PA54PA65PA76PB57PB48PB39PB210PB111PB012PC013PC114PC215PC316RESET/PA017PA118PA219PA320GND
MCU_Microchip_ATtiny:ATtiny1616-SFrom KiCad's library

Footprint

1234567891011121314151617181920
Package_SO:SOIC-20W_7.5x12.8mm_P1.27mmFrom KiCad's library

From the datasheet

13
Supply, least
1.8 V · VDD, recommended operating min · p. 506
Supply, most
5.5 V · VDD, recommended operating max · p. 506
Supply, absolute maximum
6 V · VDD, absolute max · p. 505
Works from
-40 °C · Operating ambient min, standard temperature range · p. 506
Works up to
105 °C · Operating ambient max, standard temperature range · p. 506
Takes working
10.2 mA · VDD, typical active current, 20 MHz, 5 V, peripherals disabled · p. 508
Takes at most
10.2 mA · VDD, largest stated typical active current, 20 MHz, 5 V · p. 508
Takes asleep
100 nA · VDD, typical Power-Down/Standby, all peripherals stopped, 3 V, 25°C · p. 508
A pin gives at most
40 mA · I/O pin sink/source absolute max · p. 505
Junction to air (SOIC)
44 K/W · Junction-to-ambient thermal resistance · p. 583
Junction to case (SOIC)
21 K/W · Junction-to-case thermal resistance · p. 583
Edge
1.3 ns · Typical output fall time, VDD = 5.0 V, load = 20 pF · p. 513
Edge
2.7 ns · SPI master SCK rise time, typical · p. 516

What it is and has

25
CPU
AVR® CPU · p. 1
Maximum clock
20 MHz · p. 1
Flash memory
16 KB, in-system self-programmable · p. 1
EEPROM
256 bytes · p. 1
SRAM
2 KB · p. 1
Flash endurance
10,000 write/erase cycles · p. 1
EEPROM endurance
100,000 write/erase cycles · p. 1
Data retention
40 years at 55°C · p. 1
I/O access
Single-cycle · p. 1
Interrupt controller
Two-level · p. 1
Hardware multiplier
Two-cycle · p. 1
Reset
Power-on Reset (POR) · p. 1
Brown-out detection
Brown-out Detector (BOD) · p. 1
Internal RC oscillator
16/20 MHz, low-power · p. 1
Internal ULP RC oscillator
32.768 kHz · p. 1
External crystal oscillator
32.768 kHz · p. 1
External clock
External clock input · p. 1
Programming and debugging
Single-pin Unified Program and Debug Interface (UPDI) · p. 1
Sleep modes
Idle, Standby and Power-Down · p. 90
Power-on Reset
POR · p. 1
Brown-out Detector
BOD · p. 1
CPU
AVR · p. 1
Maximum CPU clock
20 MHz · p. 1
Flash endurance
10,000 cycles · p. 1
EEPROM endurance
100,000 cycles · p. 1

Specifications

256
ParameterConditionsAs printedPage
Power supply voltage VDDmin -0.5 · max 6 V505
Current into a VDD pin IVDDT = [-40, 85]°Cmax 200 mA505
Current into a VDD pin IVDDT = [85, 125]°Cmax 100 mA505
Current out of a GND pin IGNDT = [-40, 85]°Cmax 200 mA505
Current out of a GND pin IGNDT = [85, 125]°Cmax 100 mA505
RESET pin voltage with respect to GND VRSTmin -0.5 · max 13 V505
Pin voltage with respect to GND VPINmin -0.5 V505
I/O pin sink/source current IPINmin -40 · max 40 mA505
I/O pin injection current except RESET pin Ic1(1)VPIN < GND – 0.6V or 5.5V < VPIN ≤ 6.1V; 4.9V < VDD ≤ 5.5Vmin -1 · max 1 mA505
I/O pin injection current except RESET pin Ic2(1)VPIN < GND – 0.6V or VPIN ≤ 5.5V; VDD ≤ 4.9Vmin -15 · max 15 mA505
Sum of I/O pin injection current except RESET pin Ictotmin -45 · max 45 mA505
Storage temperature Tstoragemin -65 · max 150 °C505
Operating supply voltage VDDSee note 2 concerning BOD triggering levelmin 1.8 · max 5.5 V506
Operating temperature range(1) TStandard temperature range; refer to device ordering codemin -40 · max 105 °C506
Operating temperature range(1) TExtended temperature range(3); refer to device ordering code; ensured only down to 2.7Vmin -40 · max 125 °C506
Operating system clock frequency CLK_CPUVDD = [1.8, 5.5]V; T = [-40, 105]°C(1)min 0 · max 5 MHz506
Operating system clock frequency CLK_CPUVDD = [2.7, 5.5]V; T = [-40, 105]°C(2)min 0 · max 10 MHz506
Operating system clock frequency CLK_CPUVDD = [4.5, 5.5]V; T = [-40, 105]°C(3)min 0 · max 20 MHz506
Operating system clock frequency CLK_CPUVDD = [2.7, 5.5]V; T = [-40, 125]°C(2)min 0 · max 8 MHz506
Operating system clock frequency CLK_CPUVDD = [4.5, 5.5]V; T = [-40, 125]°C(3)min 0 · max 16 MHz506
Active power consumptionCLK_CPU = 20 MHz (OSC20M); VDD = 5V; T = 25°C; peripherals disabled, without I/O drivetyp 10.2 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 5V; T = 25°C; peripherals disabled, without I/O drivetyp 5.5 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 3V; T = 25°C; peripherals disabled, without I/O drivetyp 3.1 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 5V; T = 25°C; peripherals disabled, without I/O drivetyp 3.2 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 3V; T = 25°C; peripherals disabled, without I/O drivetyp 1.8 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 2V; T = 25°C; peripherals disabled, without I/O drivetyp 1.2 mA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 5V; T = 25°C; peripherals disabled, without I/O drivetyp 13.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 3V; T = 25°C; peripherals disabled, without I/O drivetyp 7.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 2V; T = 25°C; peripherals disabled, without I/O drivetyp 5 uA508
Idle power consumptionCLK_CPU = 20 MHz (OSC20M); VDD = 5V; T = 25°C; peripherals disabled, without I/O drive; maximum based on characterizationtyp 4.3 · max 6.3 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 5V; T = 25°C; peripherals disabled, without I/O drive; maximum based on characterizationtyp 2.2 · max 3.1 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 3V; T = 25°C; peripherals disabled, without I/O drive; maximum based on characterizationtyp 1.1 · max 1.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 5V; T = 25°C; peripherals disabled, without I/O drive; maximum based on characterizationtyp 1.1 · max 1.6 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 3V; T = 25°C; peripherals disabled, without I/O drivetyp 0.6 · max 0.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 2V; T = 25°C; peripherals disabled, without I/O drivetyp 0.4 mA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 5V; T = 25°C; peripherals disabled, without I/O drive; maximum based on characterizationtyp 8.2 · max 20 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 3V; T = 25°C; peripherals disabled, without I/O drive; maximum based on characterizationtyp 4.2 · max 15 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 2V; T = 25°C; peripherals disabled, without I/O drivetyp 2.6 uA508
Standby power consumptionRTC running at 1.024 kHz from external XOSC32K (CL=7.5 pF); VDD = 3V; T = 25°Ctyp 0.69 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K; VDD = 3V; T = 25°Ctyp 0.71 · max 3 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K; VDD = 3V; T = 85°C; maximum based on characterizationmax 6 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K; VDD = 3V; T = 125°Cmax 8 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped; VDD = 3V; T = 25°Ctyp 0.1 · max 2 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped; VDD = 3V; T = 85°C; maximum based on characterizationmax 5 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped; VDD = 3V; T = 125°Cmax 7 uA508
Reset power consumptionReset line pulled down; VDD = 3V; T = 25°Ctyp 100 uA509
Start-up time from any Reset release twakeupVDD = 3V; T = 25°C; OSC20M system clocktyp 200 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 20 MHz; VDD = 5V; T = 25°Ctyp 1 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 10 MHz; VDD = 3V; T = 25°Ctyp 2 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 5 MHz; VDD = 2V; T = 25°Ctyp 4 us509
Wake-up from Standby and Power-Down sleep mode twakeupVDD = 3V; T = 25°C; OSC20M system clocktyp 10 us509
BODContinuous; VDD = 3V; T = 25°C; OSC20M at 1 MHz; Idle sleep modetyp 19 uA509
BODSampling @ 1 kHz; VDD = 3V; T = 25°C; OSC20M at 1 MHz; Idle sleep modetyp 1 uA509
TCA16-bit count @ 1 MHz; VDD = 3V; T = 25°C; Idle sleep modetyp 13 uA509
TCB16-bit count @ 1 MHz; VDD = 3V; T = 25°C; Idle sleep modetyp 7.5 uA509
RTC16-bit count @ 32.768 kHz @ OSCULP32K; VDD = 3V; T = 25°C; Idle sleep modetyp 1 uA509
VLM threshold relative to BOD triggering level VVLMBOD.VLMLVL = 0x0typ 4 %511
VLM threshold relative to BOD triggering level VVLMBOD.VLMLVL = 0x1typ 13 %511
VLM threshold relative to BOD triggering level VVLMBOD.VLMLVL = 0x2typ 25 %511
Hysteresis VHYSBODLEVEL7typ 80 mV511
Hysteresis VHYSBODLEVEL2typ 40 mV511
Hysteresis VHYSBODLEVEL0typ 25 mV511
Detection time TBODContinuoustyp 7 us511
Detection time TBODSampled, 1 kHztyp 1 ms511
Detection time TBODSampled, 125 Hztyp 8 ms511
Start-up time TStartTime from enable to readytyp 40 us511
Ensured detection for a high-voltage Reset VHVRSTmin 11.5 · max 12.5 V511
Input low-voltage for RESET VRST_VILmin -0.2 V511
Minimum pulse-width on the RESET pin tRSTmax 2.5 us511
RESET pull-up resistor RRSTVReset = 0Vmin 20 · max 60 kΩ511
Accuracy with 16 MHz and 20 MHz frequency selection relative to the factory-stored frequency value fOSC20MFactory calibrated VDD = 3V(1); T = [0, 70]°C; VDD = [1.8, 4.5]V(3)min -2 · max 2 %511
Accuracy with 16 MHz and 20 MHz frequency selection relative to the factory-stored frequency value fOSC20MFactory calibrated VDD = 5V(1); T = [0, 70]°C; VDD = [4.5, 5.5]V(3)min -2 · max 2 %511
Accuracy with 16 MHz and 20 MHz frequency selection fOSC20MFactory calibrated; T = 25°C, 3.0Vmin -3 · max 3 %511
Accuracy with 16 MHz and 20 MHz frequency selection fOSC20MFactory calibrated; T = [0, 70]°C; VDD = [1.8, 3.6]V(3)min -4 · max 4 %511
Accuracy with 16 MHz and 20 MHz frequency selection fOSC20MFactory calibrated; Full operation range(3)min -5 · max 5 %511
User calibration range fCALOSC20M(2) = 16 MHzmin 14.5 · max 17.5 MHz511
User calibration range fCALOSC20M(2) = 20 MHzmin 18.5 · max 21.5 MHz511
Frequency fCLCLVDD = [1.8, 5.5]Vmin 0 · max 5 MHz513
Frequency fCLCLVDD = [2.7, 5.5]Vmin 0 · max 10 MHz513
Frequency fCLCLVDD = [4.5, 5.5]Vmin 0 · max 20 MHz513
Clock period tCLCLVDD = [1.8, 5.5]Vmin 200 ns513
Clock period tCLCLVDD = [2.7, 5.5]Vmin 100 ns513
Clock period tCLCLVDD = [4.5, 5.5]Vmin 50 ns513
High time tCHCXVDD = [1.8, 5.5]Vmin 80 ns513
High time tCHCXVDD = [2.7, 5.5]Vmin 40 ns513
High time tCHCXVDD = [4.5, 5.5]Vmin 20 ns513
Low time tCLCXVDD = [1.8, 5.5]Vmin 80 ns513
Low time tCLCXVDD = [2.7, 5.5]Vmin 40 ns513
Low time tCLCXVDD = [4.5, 5.5]Vmin 20 ns513
Input low-voltage, except RESET pin as I/O VILmin -0.2 V513
I/O pin drive strength VOLVDD = 1.8V, IOL = 1.5 mAmax 0.36 V513
I/O pin drive strength VOLVDD = 3.0V, IOL = 7.5 mAmax 0.6 V513
I/O pin drive strength VOLVDD = 5.0V, IOL = 15 mAmax 1 V513
I/O pin drive strength VOHVDD = 1.8V, IOH = 1.5 mAmin 1.44 V513
I/O pin drive strength VOHVDD = 3.0V, IOH = 7.5 mAmin 2.4 V513
I/O pin drive strength VOHVDD = 5.0V, IOH = 15 mAmin 4 V513
Maximum combined I/O sink current per pin group(1) Itotalmax 100 mA513
Maximum combined I/O source current per pin group(1) Itotalmax 100 mA513
Input low-voltage on RESET pin as I/O VIL2min -0.2 V513
I/O pin drive strength on RESET pin as I/O VOL2VDD = 1.8V, IOL = 0.1 mAmax 0.36 V513
I/O pin drive strength on RESET pin as I/O VOL2VDD = 3.0V, IOL = 0.25 mAmax 0.6 V513
I/O pin drive strength on RESET pin as I/O VOL2VDD = 5.0V, IOL = 0.5 mAmax 1 V513
I/O pin drive strength on RESET pin as I/O VOH2VDD = 1.8V, IOH = 0.1 mAmin 1.44 V513
I/O pin drive strength on RESET pin as I/O VOH2VDD = 3.0V, IOH = 0.25 mAmin 2.4 V513
I/O pin drive strength on RESET pin as I/O VOH2VDD = 5.0V, IOH = 0.5 mAmin 4 V513
Rise time tRISEVDD = 3.0V, load = 20 pFtyp 2.5 ns513
Rise time tRISEVDD = 5.0V, load = 20 pFtyp 1.5 ns513
Fall time tFALLVDD = 3.0V, load = 20 pFtyp 2 ns513
Fall time tFALLVDD = 5.0V, load = 20 pFtyp 1.3 ns513
I/O pin capacitance except TOSC and TWI pins CPINtyp 3 pF513
I/O pin capacitance on TOSC pins CPINtyp 5.5 pF513
θJA [°C/W] θJA20-pin SOICtyp 44 °C/W583
θJC [°C/W] θJC20-pin SOICtyp 21 °C/W583
Active power consumptionCLK_CPU = 20 MHz (OSC20M), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 10.2 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 5.5 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 3V, T = 25°C, peripherals disabled, without I/O drivetyp 3.1 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 3.2 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 3V, T = 25°C, peripherals disabled, without I/O drivetyp 1.8 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 2V, T = 25°C, peripherals disabled, without I/O drivetyp 1.2 mA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 13.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 3V, T = 25°C, peripherals disabled, without I/O drivetyp 7.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 2V, T = 25°C, peripherals disabled, without I/O drivetyp 5 uA508
Idle power consumptionCLK_CPU = 20 MHz (OSC20M), VDD = 5V; typical at 25°C; maximum based on characterization, not covered by production test limitstyp 4.3 · max 6.3 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 5V; typical at 25°C; maximum based on characterization, not covered by production test limitstyp 2.2 · max 3.1 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 3V; typical at 25°C; maximum based on characterization, not covered by production test limitstyp 1.1 · max 1.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 5V; typical at 25°C; maximum based on characterization, not covered by production test limitstyp 1.1 · max 1.6 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 3V; typical at 25°Ctyp 0.6 · max 0.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 2V, T = 25°Ctyp 0.4 mA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 5V; typical at 25°C; maximum based on characterization, not covered by production test limitstyp 8.2 · max 20 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 3V; typical at 25°C; maximum based on characterization, not covered by production test limitstyp 4.2 · max 15 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 2V, T = 25°Ctyp 2.6 uA508
Standby power consumptionRTC running at 1.024 kHz from external XOSC32K (CL=7.5 pF), VDD = 3V, T = 25°Ctyp 0.69 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K, VDD = 3V, T = 25°Ctyp 0.71 · max 3 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K, VDD = 3V, T = 85°Cmax 6 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K, VDD = 3V, T = 125°Cmax 8 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped, VDD = 3V, T = 25°Ctyp 0.1 · max 2 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped, VDD = 3V, T = 85°Cmax 5 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped, VDD = 3V, T = 125°Cmax 7 uA508
Recommended Baud RateUPDICLKDIV = 0x1 (16 MHz); minimum in kbps, maximum in Mbpsmin 0.3 · max 0.9 kbps / Mbps469
Recommended Baud RateUPDICLKDIV = 0x2 (8 MHz)min 0.15 · max 450 kbps469
Recommended Baud RateUPDICLKDIV = 0x3 (4 MHz) - Defaultmin 0.075 · max 225 kbps469
Max. Total ErrorData + Parity Bits = 9; Rslow = 96.39; Rfast = 104.76min -3.61 · max 4.76 %469
Recommended Max. RX ErrorData + Parity Bits = 9; Rslow = 96.39; Rfast = 104.76min -1.5 · max 1.5 %469
Recommended BREAK Character DurationUPDICLKDIV[1:0] = 0x1 (16 MHz)typ 6.15 ms469
Recommended BREAK Character DurationUPDICLKDIV[1:0] = 0x2 (8 MHz)typ 12.3 ms469
Recommended BREAK Character DurationUPDICLKDIV[1:0] = 0x3 (4 MHz) - Defaulttyp 24.6 ms469
Reset power consumptionReset line pulled down; VDD = 3V; 25°Ctyp 100 uA509
Start-up time from any Reset release twakeupVDD = 3V; T = 25°C; OSC20Mtyp 200 us509
Wake-up from Standby and Power-Down sleep mode twakeupVDD = 3V; T = 25°C; OSC20Mtyp 10 us509
BODContinuous; VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHz; module onlytyp 19 uA509
BODSampling @ 1 kHz; VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHz; module onlytyp 1 uA509
TCA16-bit count @ 1 MHz; VDD = 3V; T = 25°C; Idle; module onlytyp 13 uA509
TCB16-bit count @ 1 MHz; VDD = 3V; T = 25°C; Idle; module onlytyp 7.5 uA509
RTC16-bit count @ 32.768 kHz @ OSCULP32K; VDD = 3V; T = 25°C; Idle; module onlytyp 1 uA509
WDT (including OSCULP32K)VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHz; module onlytyp 1 uA510
OSC20MVDD = 3V; T = 25°C; Idle; module onlytyp 125 uA510
ACFast mode; CPU in Standby; VDD = 3V; T = 25°C; module onlytyp 92 uA510
ACLow-Power mode; CPU in Standby; VDD = 3V; T = 25°C; module onlytyp 45 uA510
ADC50 ksps; VDD = 3V; T = 25°C; Idle; module onlytyp 325 uA510
ADC100 ksps; VDD = 3V; T = 25°C; Idle; module onlytyp 340 uA510
XOSC32KCL = 7.5 pF; VDD = 3V; T = 25°C; Idle; module onlytyp 0.5 uA510
OSCULP32KVDD = 3V; T = 25°C; Idle; module onlytyp 0.5 uA510
USARTEnable @ 9600 Baud; VDD = 3V; T = 25°C; Idle; module onlytyp 13 uA510
SPI (Master)Enable @ 100 kHz; VDD = 3V; T = 25°C; Idle; module onlytyp 2 uA510
TWI (Master)Enable @ 100 kHz; VDD = 3V; T = 25°C; Idle; module onlytyp 24 uA510
TWI (Slave)Enable @ 100 kHz; VDD = 3V; T = 25°C; Idle; module onlytyp 17 uA510
Flash programmingErase Operation; VDD = 3V; T = 25°C; module onlytyp 1.5 mA510
Flash programmingWrite Operation; VDD = 3V; T = 25°C; module onlytyp 3 mA510
Power-on Slope SRONmax 100 V/ms510
POR threshold voltage on VDD falling VPORVDD falls/rises at 0.5 V/ms or slowermin 0.8 · max 1.6 V510
POR threshold voltage on VDD rising VPORVDD falls/rises at 0.5 V/ms or slowermin 1.4 · max 1.8 V510
BOD triggering level (falling/rising) VBODBODLEVEL7min 3.9 · typ 4.2 · max 4.5 V510
BOD triggering level (falling/rising) VBODBODLEVEL2min 2.4 · typ 2.6 · max 2.9 V510
BOD triggering level (falling/rising) VBODBODLEVEL0min 1.7 · typ 1.8 · max 2 V510
I/O pin capacitance on TWI pins CPINtyp 10 pF514
Pull-up resistor RPmin 20 · typ 35 · max 50 kΩ514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [1.8, 5.5]V; TA = [-40, 125]°Cmax 8 MHz514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [2.7, 5.5]V; TA = [-40, 125]°Cmax 16 MHz514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [4.5, 5.5]V; TA = [-40, 105]°Cmax 32 MHz514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [4.5, 5.5]V; TA = [-40, 125]°Cmax 20 MHz514
SCK clock frequency fSCKMastermax 10 MHz514
SCK period tSCKMastermin 100 ns514
SCK rise time tSCKRMastertyp 2.7 ns516
SCK fall time tSCKFMastertyp 2.7 ns516
MISO setup to SCK tMISMastertyp 10 ns516
MISO hold after SCK tMIHMastertyp 10 ns516
MOSI hold after SCK tMOHMastertyp 1 ns516
Slave SCK clock frequency fSSCKSlavemax 5 MHz516
SCK rise time tSSCKRSlavemax 1600 ns516
SCK fall time tSSCKFSlavemax 1600 ns516
MOSI setup to SCK tSISSlavemin 3 ns516
SS setup to SCK tSSSSlavemin 21 ns516
SS hold after SCK tSSHSlavemin 20 ns516
MISO setup to SCK tSOSSlavetyp 8 ns516
MISO hold after SCK tSOHSlavetyp 13 ns516
MISO setup after SS low tSOSSSlavetyp 11 ns516
MISO hold after SS low tSOSHSlavetyp 8 ns516
SCL clock frequency fSCLMax. frequency requires system clock at 10 MHz, VDD = [2.7, 5.5]V and T = [-40, 105]°Cmin 0 · max 1000 kHz517
Output low voltage VOLIload = 3 mA, Normal mode, VDD > 2Vmax 0.4 V517
Low-level output current IOLfSCL ≤ 400 kHz, VOL = 0.4Vmin 3 mA517
Low-level output current IOLfSCL ≤ 1 MHz, VOL = 0.4Vmin 20 mA517
Capacitive load for each bus line CBfSCL ≤ 100 kHzmax 400 pF517
Capacitive load for each bus line CBfSCL ≤ 400 kHzmax 400 pF517
Capacitive load for each bus line CBfSCL ≤ 1 MHzmax 550 pF517
Rise time for both SDA and SCL tRfSCL ≤ 100 kHzmax 1000 ns517
Rise time for both SDA and SCL tRfSCL ≤ 400 kHzmin 20 · max 300 ns517
Rise time for both SDA and SCL tRfSCL ≤ 1 MHzmax 120 ns517
Output fall time from VIHmin to VILmax tOF10 pF < Capacitance of bus line < 400 pF; fSCL ≤ 400 kHz; minimum specified as 20 × (VDD/5.5V) nsmax 250 ns517
Output fall time from VIHmin to VILmax tOF10 pF < Capacitance of bus line < 400 pF; fSCL ≤ 1 MHz; minimum specified as 20 × (VDD/5.5V) nsmax 120 ns517
Spikes suppressed by Input filter tSPmin 0 · max 50 ns517
Input current for each I/O pin IL0.1×VDD < VI < 0.9×VDDmax 1 uA517
Capacitance for each I/O pin CImax 10 pF517
Internal reference voltage INT11VVDD = [1.8V, 3.6V]; T = [0, 105]°Cmin -2 · max 2 %520
Internal reference voltage INT055V, INT15V, INT25VVDD = [1.8V, 3.6V]; T = [0, 105]°Cmin -3 · max 3 %520
Internal reference voltage INT055V, INT11V, INT15V, INT25V, INT43VVDD = [1.8V, 5.5V]; T = [-40, 125]°Cmin -5 · max 5 %520
Internal reference voltage INT055V, INT11V, INT15V, INT25VVDD = [1.8V, 3.6V]; T = [0, 105]°Cmin -3 · max 3 %520
Supply voltage VDDADCmin 1.8 · max 5.5 V520
Reference voltage VREFADC; REFSEL = Internal referencemin 0.55 V521
Reference voltage VREFADC; REFSEL = VDDmin 1.8 · max 5.5 V521
Input capacitance CINADC; SAMPCAP = 5 pFtyp 5 pF521
Input capacitance CINADC; SAMPCAP = 10 pFtyp 10 pF521
Input resistance RINADCtyp 14 kΩ521
Input voltage range VINADCmin 0 V521
Input bandwidth IBANDADC; 1.1V ≤ VREFmax 57.5 kHz521
Sample rate fADCADC; 1.1V ≤ VREFmin 15 · max 115 ksps521
Sample rate fADCADC; 1.1V ≤ VREF (8-bit resolution)min 15 · max 150 ksps521
Sample rate fADCADC; VREF = 0.55V (10 bits)min 7.5 · max 20 ksps521
Clock frequency CLKADCADC; VREF = 0.55V (10 bits)min 100 · max 260 kHz521
Clock frequency CLKADCADC; 1.1V ≤ VREF (10 bits)min 200 · max 1500 kHz521
Clock frequency CLKADCADC; 1.1V ≤ VREF (8-bit resolution); 50% duty cycle required above 1500 kHzmin 200 · max 2000 kHz521
Sampling time TsADCmin 2 · typ 2 · max 33 CLKADC cycles521
Conversion time (latency) TCONVADC; Sampling time = 2 CLKADCmin 8.7 · max 50 us521
Start-up time TSTARTADC; Internal VREFtyp 22 us521
Resolution RESADCtyp 10 bit521
Integral nonlinearity INLADC; REFSEL = INTERNAL; VREF = 0.55V; fADC = 7.7 kspstyp 1 LSb521
Integral nonlinearity INLADC; REFSEL = INTERNAL or VDD; 1.1V ≤ VREF; fADC = 15 kspstyp 1 LSb521
Integral nonlinearity INLADC; REFSEL = INTERNAL or VDD; 1.1V ≤ VREF; fADC = 77 kspstyp 1 LSb521
Integral nonlinearity INLADC; REFSEL = INTERNAL or VDD; 1.1V ≤ VREF; fADC = 115 kspstyp 1.2 LSb521
Conversion resolution TRES10 bitstyp 0.55 °C523
Conversion time tCONV1 MHz ADC clocktyp 13 us523
Supply voltage VDDDAC; supply must meet VDD specification for VREF level usedmin 1.8 · typ 3 · max 5.5 V523
Resistive external load RLoadDAC; VDD = 3Vmin 5 kΩ523
Capacitive external load CLoadDAC; VDD = 3Vmax 30 pF523
Output voltage range VOUTDAC; VDD = 3Vmin 0.2 V523
Output sink/source IOUTDAC; VDD = 3Vtyp 1 mA523
Maximum conversion rate fDACDAC; 0.55V ≤ VREF ≤ 2.5Vtyp 350 ksps523
Maximum conversion rate fDACDAC; VREF = 4.3Vtyp 270 ksps523
Resolution RESDACmax 8 bits523
Integral nonlinearity INLDAC; 0.55V ≤ VREF ≤ 4.3V; calculated over 5% to 95% rangemin -1.2 · typ 0.3 · max 1.2 LSb523
Differential nonlinearity DNLDAC; 0.55V ≤ VREF ≤ 4.3V; calculated over 5% to 95% rangemin -1 · typ 0.25 · max 1 LSb523
Offset error EOFFDAC; 0.55V ≤ VREF ≤ 1.5V; includes output buffer offset, measured at DAC output pinmin -25 · typ -3 · max 20 mV523
Offset error EOFFDAC; VREF = 2.5V; includes output buffer offset, measured at DAC output pinmin -30 · typ -6 · max 10 mV523
Offset error EOFFDAC; VREF = 4.3V; includes output buffer offset, measured at DAC output pinmin -40 · typ -10 · max 0 mV523
Gain error EGAINDAC; 0.55V ≤ VREF ≤ 4.3V; includes VREF accuracymin -10 · typ -1 · max 10 LSb523
θJA θJA20-pin SOICtyp 44 °C/W583
θJC θJC20-pin SOICtyp 21 °C/W583

Open-source boards using it

27See all 27
  • 2 layers50.8 × 50.8 mmDC2026 LASIR, the printed circuit board in 3D

    DC2026 LASIR

    CmdrZin/chips_avr_examples

    AVR assembly and C code for robotics and other projects.

    38 parts6MIT
  • 4 layers174 × 29 mmOneWheelBMS, the printed circuit board in 3D

    OneWheelBMS

    ocornu/OneWheelBMS

    Open source BMS for OneWheel v1/plus

    98 parts3MIT
  • 2 layers25.4 × 28.8 mmKicad linear, the printed circuit board in 3D

    Kicad linear

    fjalvingh/8bit-busdisplay

    PCB for showing an 8 bit hex number from a 5V bus on a 7-segment display using an ATTINY1616

    7 parts1
  • 2 layers85.6 × 54 mmPersonalPCB BC, the printed circuit board in 3D

    PersonalPCB BC

    Bumb1eris/PCB_Business_Card

    A coin cell powered PCB business card that can play snake

    73 partsMIT
  • 2 layers80.5 × 53.8 mmBlynk, the printed circuit board in 3D

    Blynk

    DynamicWhiteHat/Blynk

    A feature-rich LED controller

    110 parts
  • 2 layers81.2 × 46.1 mmLightmeter, the printed circuit board in 3D

    Lightmeter

    empdo/lightmeter

    An open-hardware handheld photographic light meter. Set shutter speed and ISO on two dials, press the button, and one of nine LEDs lights up to show the aperture you should use. Runs from a single CR2032.

    47 parts
  • 2 layers131.7 × 80 mmKm1105, the printed circuit board in 3D

    Km1105

    fjalvingh/km11

    PDP-11 KM11 maintenance module, using an LCD screen

    46 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ATTINY1616-SN?

Yes. The symbol is MCU_Microchip_ATtiny:ATtiny1616-S and the footprint Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ATTINY1616-SN?

SOIC-20-300mil, with 20 pins. Its footprint is drawn on this page.

Where is the ATTINY1616-SN datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the ATTINY1616-SN?

JLCPCB lists it as part C609652, with 368 in stock; the sellers' links on this page open their listings.

What can replace the ATTINY1616-SN?

Parts like it in the library: the STC15W408AS-35I-SOP20 by STC Micro, the STC12C5204AD-35I-SOP20 by STC Micro, the SC92F7352M20U by SOC and the STC11F04E-35I-SOP20 by STC Micro. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ATTINY1616-SN?

27 boards in 21 repositories on GitHub; the most starred are listed on this page, with their KiCad files.