
SPH0641LU4H-1
KnowlesExtended
-26dB 0.98mm 1.8V 2.65mm 235uA~270uA 3.5mm 64.3dB Omnidirectional Omnidirectional pickup LGA-5(3.5x2.7) MEMS Microphones ROHS
- Part id
- knowles/SPH0641LU4H-1
- Category
- MEMS Microphones
- Package
- LGA-5(3.5x2.7)
- Pins
- 5
- In stock
- 179 at JLCPCB (C2879853)
- Used on
- 36 open-source boards
Overview
The SPH0641LU4H-1 is a MEMS Microphone made by Knowles in a LGA-5(3.5x2.7) package with 5 pins. -26dB 0.98mm 1.8V 2.65mm 235uA~270uA 3.5mm 64.3dB Omnidirectional Omnidirectional pickup LGA-5(3.5x2.7) MEMS Microphones ROHS.
PCBKit's library has its KiCad symbol (Sensor_Audio:SPH0641LU4H-1, from KiCad's library) and its footprint (Sensor_Audio:Knowles_LGA-5_3.5x2.65mm, from KiCad's library), ready for a KiCad board. 179 are in stock at JLCPCB (part C2879853). 36 open-source boards in 29 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
6- Supply, least
- 1.62 V · VDD, recommended operating min · p. 2
- Supply, most
- 3.6 V · VDD, recommended operating max · p. 2
- Supply, absolute maximum
- 5 V · VDD to Ground, absolute max · p. 2
- Takes working
- 620 µA · Standard Performance Mode, typical, VDD = 1.8 V, fCLOCK = 2.4 MHz · p. 3
- Takes at most
- 1 mA · Ultrasonic Mode supply current max, VDD = 1.8 V, fCLOCK = 3.072 MHz · p. 3
- Takes asleep
- 80 µA · Sleep Mode typical, fCLOCK ≤ 250 kHz · p. 2
What it is and has
7- Signal to noise ratio
- 64.3dB · p. 1
- Frequency response
- Flat · p. 1
- RF shielding
- RF Shielded · p. 1
- Channels
- Supports Dual Multiplexed Channels · p. 1
- Directivity
- Omnidirectional · p. 1
- Ultrasonic support
- Supported · p. 1
- Package
- LGA · p. 1
Specifications
49| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| VDD, DATA to Ground | min -0.3 · max 5 V | 2 | |
| CLOCK to Ground | min -0.3 · max 5 V | 2 | |
| SELECT to Ground | min -0.3 · max 5 V | 2 | |
| Input Current | min -5 · max 5 mA | 2 | |
| Temperature Range | min -40 · max 100 °C | 2 | |
| Supply Voltage VDD | 23 ±2°C, 55±20% R.H., fCLOCK=2.4 MHz, SELECT pin grounded, no load | min 1.62 · max 3.6 V | 2 |
| Clock Frequency Range | Sleep Mode | min 0 · max 250 KHz | 2 |
| Clock Frequency Range | Low-Power Mode | min 351 · max 815 KHz | 2 |
| Clock Frequency Range | Standard Performance Mode | min 1.024 · max 2.475 MHz | 2 |
| Clock Frequency Range | Ultrasonic Mode | min 3.072 · max 4.8 MHz | 2 |
| Sleep Current ISLEEP | fCLOCK ≤ 250 kHz; VDD=1.8 V | typ 80 uA | 2 |
| DC Output | Fullscale = ±100 | typ 0 % FS | 2 |
| Short Circuit Current ISC | Grounded DATA pin | min 1 · max 20 mA | 2 |
| Output Load CLOAD | max 140 pF | 2 | |
| Fall-asleep Time | fCLOCK ≤ 250 kHz | max 10 ms | 2 |
| Wake-up Time | fCLOCK ≥ 351 kHz | max 15 ms | 2 |
| Power-up Time | VDD ≥ V(min) | max 50 ms | 3 |
| Mode-Change Time | max 10 ms | 3 | |
| Supply Current IDD | fCLOCK =3.072 MHz, VDD=1.8 V | typ 845 · max 1000 uA | 3 |
| Sensitivity S | 94 dB SPL @ 1 kHz; fCLOCK =3.072 MHz, VDD=1.8 V | min -27 · typ -26 · max -25 dBFS | 3 |
| Signal to Noise Ratio SNR | 94 dB SPL @ 1 kHz, A-weighted; fCLOCK =3.072 MHz, VDD=1.8 V | typ 64.3 dB(A) | 3 |
| Total Harmonic Distortion THD | 94 dB SPL @ 1 kHz, S = Typ; fCLOCK =3.072 MHz, VDD=1.8 V | typ 0.2 % | 3 |
| Acoustic Overload Point AOP | 10% THD @ 1 kHz, S = Typ; fCLOCK =3.072 MHz, VDD=1.8 V | typ 120 dB SPL | 3 |
| Power Supply Rejection Ratio PSRR | 200 mVpp sinewave @ 1 kHz; fCLOCK =3.072 MHz, VDD=1.8 V | typ 55 dBV/FS | 3 |
| Power Supply Rejection PSR+N | 100 mVpp square wave @ 217 Hz, A-weighted; fCLOCK =3.072 MHz, VDD=1.8 V | typ -84 dBFS (A) | 3 |
| Supply Current IDD | fCLOCK=2.4 MHz, VDD=1.8 V | typ 620 · max 700 uA | 3 |
| Sensitivity S | 94 dB SPL @ 1 kHz; fCLOCK = 2.4 MHz, VDD=1.8 V | min -27 · typ -26 · max -25 dBFS | 3 |
| Signal to Noise Ratio SNR | 94 dB SPL @ 1 kHz, A-weighted, fCLOCK=2.4 MHz, VDD=1.8 V | typ 64.3 dB(A) | 3 |
| Total Harmonic Distortion THD | 94 dB SPL @ 1 kHz, S = Typ; fCLOCK = 2.4 MHz, VDD=1.8 V | typ 0.2 % | 3 |
| Acoustic Overload Point AOP | 10% THD @ 1 kHz, S = Typ; fCLOCK = 2.4 MHz, VDD=1.8 V | typ 120 dB SPL | 3 |
| Power Supply Rejection Ratio PSRR | 200 mVpp sinewave @ 1 kHz; fCLOCK = 2.4 MHz, VDD=1.8 V | typ 55 dBV/FS | 3 |
| Power Supply Rejection PSR+N | 100 mVpp square wave @ 217 Hz, A-weighted; fCLOCK = 2.4 MHz, VDD=1.8 V | typ -84 dBFS (A) | 3 |
| Supply Current IDD | fCLOCK=768 kHz, VDD=1.8 V | typ 235 · max 270 uA | 4 |
| Sensitivity S | 94 dB SPL @ 1 kHz; fCLOCK = 768 kHz, VDD=1.8 V | min -27 · typ -26 · max -25 dBFS | 4 |
| Signal to Noise Ratio SNR | 94 dB SPL @ 1 kHz, A-weighted (20 Hz - 8 kHz); fCLOCK = 768 kHz, VDD=1.8 V | typ 64 dB(A) | 4 |
| Total Harmonic Distortion THD | 94 dB SPL @ 1 kHz, S = Typ; fCLOCK = 768 kHz, VDD=1.8 V | typ 0.2 % | 4 |
| Acoustic Overload Point AOP | 10% THD @ 1 kHz, S = Typ; fCLOCK = 768 kHz, VDD=1.8 V | typ 120 dB SPL | 4 |
| Power Supply Rejection Ratio PSRR | 200 mVpp sinewave @ 1 kHz; fCLOCK = 768 kHz, VDD=1.8 V | typ 59 dBV/FS | 4 |
| Power Supply Rejection PSR+N | 100 mVpp square wave@ 217 Hz, A-weighted (20Hz - 8kHz); fCLOCK = 768 kHz, VDD=1.8 V | typ -86 dBFS (A) | 4 |
| Logic Input High VIH | Minimum: 0.7xVDD | max 3.6 V | 4 |
| Logic Input Low VIL | Maximum: 0.3xVDD | min -0.3 V | 4 |
| Logic Output Low VOL | IOUT = 2 mA | min 0 · max 0.45 V | 4 |
| Clock Duty Cycle | fCLOCK ≤ 2.4 MHz | min 40 · max 60 % | 4 |
| Clock Duty Cycle | 2.4MHz < fCLOCK ≤ 4.8 MHz | min 48 · typ 50 · max 52 % | 4 |
| Clock Rise/Fall Time tEDGE | max 3 ns | 4 | |
| Delay Time for Data Assertion tDD | min 18 · typ 28 · max 40 ns | 4 | |
| Delay Time for High Z tDZ | min 3 · max 16 ns | 4 | |
| ESD-LID/GND | 3 discharges of ±8 kV direct contact to lid while unit is grounded; IEC 61000-4-2 | min -8 · max 8 kV | 14 |
| ESD-MM | 3 discharges of ±200V direct contact to I/O pins; ESD STM5.2 | min -200 · max 200 V | 14 |
- 4 layers179.6 × 161 mm

- 2 layers

Ssl
meerstern/Sound_Direction_Sensor
This board detects the direction of sound with 4-pdm mems mic using GCC-PHAT algorithm.
56 parts17 - 2 layers20 × 15 mm

- 4 layers57 × 56 mm

Iot led strip pcb
0xjmux/iot_leddriver_hw
ESP32-based WS2812B LED Strip Driver PCB, designed for music visualization
85 parts9 - 2 layers100 × 100 mm

Acoustic camera
mhbbParsa/acoustic_camera
FPGA acoustic camera with real-time sound source localisation using Goertzel beamforming, displayed as a live heatmap on VGA/webcam overlay
68 parts6MIT - 2 layers43.2 × 44.5 mm

- 2 layers67.1 × 88.4 mm

DE429 001 INSTALL
Purdue-Northwest-Vibration-Anaylsis/Purdue-Northwest-Vibration-Analysis
Vibration analysis senior design project for purdue northwest.
48 parts2 - 2 layers75 × 5.5 mm

Cc ring
JackToaster/Wearable-LED-Ring
Tiny LED ring with a microphone for wearable music-reactive lighting
42 parts1
Questions
Is there a KiCad symbol and footprint for the SPH0641LU4H-1?
Yes. The symbol is Sensor_Audio:SPH0641LU4H-1 and the footprint Sensor_Audio:Knowles_LGA-5_3.5x2.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the SPH0641LU4H-1?
LGA-5(3.5x2.7), with 5 pins. Its footprint is drawn on this page.
Where is the SPH0641LU4H-1 datasheet?
Knowles publishes it: the Datasheet link on this page opens it.
Where can I order the SPH0641LU4H-1?
JLCPCB lists it as part C2879853, with 179 in stock; the sellers' links on this page open their listings.
Which open-source boards use the SPH0641LU4H-1?
36 boards in 29 repositories on GitHub; the most starred are listed on this page, with their KiCad files.