Skip to the content
12345

ADP7182AUJZ-2.5-R7

Analog DevicesExtended

-40℃~+125℃@(Tj) 1 185mV@(200mA) 18uVrms 2.5V 200mA 28V 650uA 66dB@(10kHz) Fixed Negative Over Current Protection、Over Temperature Protection、Enable TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
adi/ADP7182AUJZ-2.5-R7
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
TSOT-23-5
Pins
5
In stock
281 at JLCPCB (C462196)
Used on
8 open-source boards

Overview

The ADP7182AUJZ-2.5-R7 is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Analog Devices in a TSOT-23-5 package with 5 pins. -40℃~+125℃@(Tj) 1 185mV@(200mA) 18uVrms 2.5V 200mA 28V 650uA 66dB@(10kHz) Fixed Negative Over Current Protection、Over Temperature Protection、Enable TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:ADP7182AUJZ-2.5, from KiCad's library) and its footprint (Package_TO_SOT_SMD:TSOT-23-5, from KiCad's library), ready for a KiCad board. 281 are in stock at JLCPCB (part C462196). 8 open-source boards in 7 repositories on GitHub use it.

Symbol

1GND2VIN3EN5VOUT
Regulator_Linear:ADP7182AUJZ-2.5From KiCad's library

Footprint

12345
Package_TO_SOT_SMD:TSOT-23-5From KiCad's library

Pinout

5
The pins of the ADP7182AUJZ-2.5-R7
PinNameType
1GNDPower in
2VINPower in
3ENInput
4NCNot connected
5VOUTPower out

Open-source boards using it

8
  • 2 layers48.8 × 18.5 mmCurmea, the printed circuit board in 3D

    Curmea

    Ledger-Donjon/curmea

    To analyze the power consumption of a component, it is common to measure the current going to the ground by placing a small resistor and measuring the voltage across it.

    30 parts2LGPL-3.0
  • 2 layers177.8 × 82.6 mmBaku, the printed circuit board in 3D

    Baku

    Demonpore-sys/baku

    49 parts
  • 4 layers150 × 50 mmTiepieLCR, the printed circuit board in 3D

    TiepieLCR

    martijnschouten/tiepielcr-hardware

    Contains the design files of the TiePieLCR multi-frequency spectrometer front-end

    241 partsGPL-3.0
  • 6 layers69.7 × 114.8 mmLow noise power probe, the printed circuit board in 3D

    Low noise power probe

    blinken/power-rail-probe

    Low-noise oscilloscope power rail probe

    118 parts101
  • 2 layers90 × 88.4 mmAdc, the printed circuit board in 3D

    Adc

    zapta/daq

    A modular data acquisition system.

    117 parts1
  • 4 layers49.4 × 111.4 mmEeg hardware v1, the printed circuit board in 3D

    Eeg hardware v1

    es-ude/eeg-hardware

    Repo of the Custom Hardware Design Files of the EEG-based Gaming Controller

    412 partsMIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ADP7182AUJZ-2.5-R7?

Yes. The symbol is Regulator_Linear:ADP7182AUJZ-2.5 and the footprint Package_TO_SOT_SMD:TSOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ADP7182AUJZ-2.5-R7?

TSOT-23-5, with 5 pins. Its footprint is drawn on this page.

Where is the ADP7182AUJZ-2.5-R7 datasheet?

Analog Devices publishes it: the Datasheet link on this page opens it.

Where can I order the ADP7182AUJZ-2.5-R7?

JLCPCB lists it as part C462196, with 281 in stock; the sellers' links on this page open their listings.

What can replace the ADP7182AUJZ-2.5-R7?

Parts like it in the library: the LR8103B-T25 by LR, the ME6211C25M5G-N by MICRONE, the LP5907MFX-2.5 by Texas Instruments and the TPS72325DBV by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ADP7182AUJZ-2.5-R7?

8 boards in 7 repositories on GitHub; the most starred are listed on this page, with their KiCad files.