Skip to the content
2 layers70.5 × 55.2 mmMidi Controller-01, the printed circuit board in 3D

A bare-metal MIDI controller built on a custon PCB. Two illuminated push buttons send note on/off messages, and two potentiometers send MIDI CC. Written in C with direct register manipulation (not Arduino libraries)

Size
70.5 × 55.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
34
Pads
99
Tracks, vias
214, 12
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
27 Jul 2026
Updated
27 Jul 2026

Overview

Midi Controller-01 is an open-source printed circuit board by zzzzzackhann, from the zzzzzackhann/ATmega-MIDI-Controller repository on GitHub. It is a 2-layer board of 70.5 × 55.2 mm with 24 parts on 34 nets, routed with 214 tracks and 12 vias.

It is built around the ATMEGA328P-AU. Its parts include 5 capacitors, 5 resistors, 3 switches, 1 IC and 1 connector. It belongs with the audio and music boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

ATmega328P MIDI Controller

A bare-metal MIDI controller built on a custon PCB. Two illuminated push buttons send note on/off messages, and two potentiometers send MIDI CC. Written in C with direct register manipulation (not Arduino libraries)

What I built

  • Hand-coded firmware in bare-metal C (UART, timers, interrupts, ADC)
  • Custom PCB designed in KiCad (schematic, PCB layout), manufactered by JLCPCB
  • Sourced parts and hand-soldered board
  • Used Arduino as ISP device to flash program to board

What I learned

  • MIDI protocol and DIN electrical spec
  • Fuse config for external 16MHz crystal
  • debugging with raw byte inspection

What I would do differently

  • incorporate dedicated power port, instead of needing 5V from headers
  • add more buttons and pots
  • use different LED buttons and vertical pots, instead of horizontal pots

Hardware

  • ATmega328P, 5-pin DIN female connector, 16MHz crystal, illuminated push-buttons

Parts

24
QtyValueFootprintReferences
3100nFCapacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mmC1, C2, C3
2100kPotentiometer_THT:PTN16A100120K1B1RV1, RV2
2220 @ 5%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2
222pFCapacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mmC4, C5
2270Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4, R5
2PB_86_A1Button_Switch_THT:PB_86_A1SW2, SW3
110kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3
116MHzCrystal:Crystal_HC49-4H_VerticalY1
1ATmega328P-APackage_QFP:TQFP-32_7x7mm_P0.8mmU1
1ISP HeaderConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalISP
1MIDI_OUTConnector_DIN:KCDX5SN2J2
1Reset ButtonConnector_Wire:SolderWire-0.5sqmm_1x02_P4.8mm_D0.9mm_OD2.3mmSW1
1UART HeaderConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalUART

The 20 most common of 24 parts.

Similar boards

  • 2 layers50.5 × 128.5 mmOpenThereminV45, the printed circuit board in 3D

    OpenThereminV45

    GaudiLabs/OpenThereminV4

    Open Source Theremin Instrument

    107 parts249GPL-3.0
  • 2 layers152 × 88 mmRFBitBangSMT, the printed circuit board in 3D

    RFBitBangSMT

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    271 parts222
  • 2 layers50.2 × 31.2 mmMCU Datalogger, the printed circuit board in 3D

    MCU Datalogger

    futureshocked/KLP4e_MCU-Datalogger

    This is the repository for the "MCU Datalogger" project.

    31 parts138MIT
  • 2 layers34 × 46 mmNfcemu, the printed circuit board in 3D

    Nfcemu

    solosky/nfc-emu

    NFC模拟器

    58 parts117Apache-2.0
  • 2 layers73 × 94 mmSportiduino base, the printed circuit board in 3D

    Sportiduino base

    sportiduino/sportiduino

    Electronic timing system for orienteering and similar outdoor sports events on Arduino

    119 parts78GPL-3.0
  • 2 layers58.9 × 44.2 mmOpenPSX2AmigaPadAdapter, the printed circuit board in 3D

    OpenPSX2AmigaPadAdapter

    SukkoPera/OpenPSX2AmigaPadAdapter

    Playstation to Commodore Amiga/CD32 Controller Adapter

    43 parts69
  • 2 layers60 × 50 mmVx8 gps prototype v2.0, the printed circuit board in 3D

    Vx8 gps prototype v2.0

    4x1md/vx8_gps

    DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.

    56 parts66MIT

Questions

How big is the Midi Controller-01 PCB?

It measures 70.5 × 55.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Midi Controller-01 use?

24 parts, built around the ATMEGA328P-AU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Midi Controller-01 KiCad files?

From the zzzzzackhann/ATmega-MIDI-Controller repository on GitHub, at the commit this page was made from: the board is Midi-Controller-01/Midi-Controller-01.kicad_pcb and its schematic Midi-Controller-01/Midi-Controller-01.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Midi Controller-01 design in my own project?

Its repository states no licence, so its author keeps all rights: ask zzzzzackhann before reusing the design.