
PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

Bringing the TI-92's back to life
Ti92 is an open-source printed circuit board by zortness, from the zortness/ti92-redux repository on GitHub, published under the MIT licence. It is a 2-layer board of 201.9 × 112.4 mm with 181 parts on 114 nets, routed with 1,221 tracks and 240 vias.
It is built around the 1N4148W. Its parts include 80 diodes, 64 switches and 1 IC.
Bringing the TI-92's back to life.

My first graphing calculator and introduction to portable programming was an early TI-85. I became enamoured with the TI calculators in the 90s, longing for a TI-92 when they were announced, but never able to purchase one. Now, you can find them in various conditions for relatively cheap on the internet.
Unfortunately, the most common issues seem to be screen related, and the screens on the TI-92 are not easily repaired. Such was the case with one of the TI-92s I purchased, so I began thinking about how I could make use of this iconic chasis.
I found other projects, notably one seen on Hackaday, the TI-92 Revive project and corresponding github repo. This is a cool project in a similar vein, but I wanted to make some different design decisions.
For several parts of this build, I traced the original components (PCB, back plate, etc) onto a piece of paper, then scanned them with a flat bed scanner. I then took the drawings and traced them into SVG's set to the correct dimensions using InkScape so I could use them with other tools such as KiCad and OpenSCAD. I also printed multiple versions of the PCB and various chasis bits on my 3D printer to work toward getting the correct fitment with the original chasis pieces.
Most of the SVGs and drawings are included here.

The PCB is designed in KiCad 7. The board is designed as a custom keyboard, using a Pi Pico (or Pico W) as the keybord controller. The routing is all done by hand with an attempt at keeping the jumps minimal.
Note: The PCB has tabs and holes to hold an SBC that lines up with the Raspberry Pi mounting holes.

I was able to solder all of this with a relatively large soldering iron and some tweezers. Tin one of the pads for the component first, then heat it up again and set the part on the pad. Only solder the second pad when you're happy with the alignment.
I used a Raspberry Pi 4 as my SBC.
To pair with the Pi 4, I used the Pimoroni Hyperpixel 4.0" Touch Display. This display is pretty expensive, but I purchased this a while ago, and noticing it seemed to fit perfectly into the TI-92 chasis is one of the factors that pushed me into completing this project.
A 4" screen of this ratio fits almost perfectly into the TI-92.
I used OpenSCAD to assemble the designs for printing. Most of the prints are derived from one or more SVG drawings, the back plate being the most complicated.
During development, I dropped my keyboard and had to chase keys across the house multiple times. I ultimately ended up finding all of my keys, but there is a basic key file included in case you need to print one.
I chose the KMK firmware (as opposed to something like QMK ) mostly due to ease of use and direct support for the Pi Pico and Pico W. This has the added bonus of being able to easily reprogram the keyboard from the finished device itself, using the keyboard itself to make changes.
Follow the instructions for installing the KMK firmware on the device (basically copy most of the files included in their release). Then drag and drop the firmware/code.py file onto the device and it should be ready to go.
There is no power supply built into this project. For my personal prototype, I'm using a 2x18650 container with a built-in on/off switch into a cheap buck converter. I also attempted to use a L7805 5V linear regulator, and while it works, even with a heat sink it will get very hot.
I am currently powering the Pi Pico W through the USB cable that connects it to the Pi 4.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 80 | 1N4148W | Diode_SMD:D_SOD-123 | D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, DA1, DADD1, DAPP1, DB1, DBKSP1, DC1 +64 |
| 1 | 0 | ti92Library:tibuttonpad | SW81 |
| 1 | 1 | ti92Library:tibuttonpad | SW77 |
| 1 | 2 | ti92Library:tibuttonpad | SW78 |
| 1 | 3 | ti92Library:tibuttonpad | SW79 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.5mm | TP11 |
| 1 | 3V3EN | TestPoint:TestPoint_Pad_D1.5mm | TP12 |
| 1 | 4 | ti92Library:tibuttonpad | SW73 |
| 1 | 5 | ti92Library:tibuttonpad | SW74 |
| 1 | 6 | ti92Library:tibuttonpad | SW75 |
| 1 | 7 | ti92Library:tibuttonpad | SW69 |
| 1 | 8 | ti92Library:tibuttonpad | SW70 |
| 1 | 9 | ti92Library:tibuttonpad | SW71 |
| 1 | AGND | TestPoint:TestPoint_Pad_D1.5mm | TP8 |
| 1 | AREF | TestPoint:TestPoint_Pad_D1.5mm | TP10 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.5mm | TP3 |
| 1 | GP0 | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | GP1 | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | GP26 | TestPoint:TestPoint_Pad_D1.5mm | TP6 |
| 1 | GP27 | TestPoint:TestPoint_Pad_D1.5mm | TP7 |
| 1 | GP28 | TestPoint:TestPoint_Pad_D1.5mm | TP9 |
| 1 | GP4 | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | GP5 | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | Reset | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW86 |
| 1 | VBUS | TestPoint:TestPoint_Pad_D1.5mm | TP14 |
| 1 | VSYS | TestPoint:TestPoint_Pad_D1.5mm | TP13 |
| 1 | a | ti92Library:tibuttonpad | SW12 |
| 1 | add | ti92Library:tibuttonpad | SW80 |
| 1 | appsA | ti92Library:tibuttonpad | SW54 |
| 1 | appsB | ti92Library:tibuttonpad | SW58 |
| 1 | b | ti92Library:tibuttonpad | SW36 |
| 1 | bksp | ti92Library:tibuttonpad | SW46 |
| 1 | c | ti92Library:tibuttonpad | SW34 |
| 1 | clear | ti92Library:tibuttonpad | SW49 |
| 1 | comma | ti92Library:tibuttonpad | SW66 |
| 1 | cos | ti92Library:tibuttonpad | SW55 |
| 1 | d | ti92Library:tibuttonpad | SW26 |
| 1 | div | ti92Library:tibuttonpad | SW68 |
| 1 | down | ti92Library:tibuttonpad | SW62 |
| 1 | e | ti92Library:tibuttonpad | SW18 |
| 1 | enter1A | ti92Library:tibuttonpad | SW40 |
| 1 | enter1B | ti92Library:tibuttonpad | SW45 |
| 1 | enter2A | ti92Library:tibuttonpad | SW63 |
| 1 | enter2B | ti92Library:tibuttonpad | SW64 |
| 1 | enter3 | ti92Library:tibuttonpad | SW84 |
| 1 | eq | ti92Library:tibuttonpad | SW85 |
| 1 | escA | ti92Library:tibuttonpad | SW53 |
| 1 | escB | ti92Library:tibuttonpad | SW57 |
| 1 | exp | ti92Library:tibuttonpad | SW67 |
| 1 | f | ti92Library:tibuttonpad | SW27 |
| 1 | f1 | ti92Library:tibuttonpad | SW2 |
| 1 | f2 | ti92Library:tibuttonpad | SW4 |
| 1 | f3 | ti92Library:tibuttonpad | SW6 |
| 1 | f4 | ti92Library:tibuttonpad | SW8 |
| 1 | f5 | ti92Library:tibuttonpad | SW3 |
| 1 | f6 | ti92Library:tibuttonpad | SW5 |
| 1 | f7 | ti92Library:tibuttonpad | SW7 |
| 1 | f8 | ti92Library:tibuttonpad | SW9 |
| 1 | func | ti92Library:tibuttonpad | SW17 |
| 1 | g | ti92Library:tibuttonpad | SW28 |
| 1 | h | ti92Library:tibuttonpad | SW29 |
| 1 | i | ti92Library:tibuttonpad | SW23 |
| 1 | j | ti92Library:tibuttonpad | SW30 |
| 1 | k | ti92Library:tibuttonpad | SW31 |
| 1 | l | ti92Library:tibuttonpad | SW32 |
| 1 | lalt | ti92Library:tibuttonpad | SW41 |
| 1 | left | ti92Library:tibuttonpad | SW60 |
| 1 | ln | ti92Library:tibuttonpad | SW50 |
| 1 | lock | ti92Library:tibuttonpad | SW1 |
| 1 | lparen | ti92Library:tibuttonpad | SW52 |
| 1 | m | ti92Library:tibuttonpad | SW38 |
| 1 | mode | ti92Library:tibuttonpad | SW48 |
| 1 | mult | ti92Library:tibuttonpad | SW72 |
| 1 | n | ti92Library:tibuttonpad | SW37 |
| 1 | neg | ti92Library:tibuttonpad | SW83 |
| 1 | o | ti92Library:tibuttonpad | SW24 |
| 1 | p | ti92Library:tibuttonpad | SW25 |
| 1 | period | ti92Library:tibuttonpad | SW82 |
| 1 | pi_pico_w | ti92Library:pi_pico_w | U1 |
| 1 | power | ti92Library:tibuttonpad | SW16 |
The 159 most common of 181 parts.

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

pierrechevalier83/ferris
A low profile split keyboard designed to satisfy one single use case elegantly



MickiusMousius/Rolio46Keyboard
A split wireless keyboard based on the Corne and Sofle


sadekbaroudi/bgkeeb
This is a reversible 100mm x 100mm pcb with support for mx or choc switches (no hotswap), per key led, rotary encoders, and exposes the SDA/SCL/GND/VCC lines in the form of the pimoroni trackball pins (meaning you can…

It measures 201.9 × 112.4 mm and has 2 copper layers, 1.6 mm thick.
181 parts, built around the 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the zortness/ti92-redux repository on GitHub, at the commit this page was made from: the board is ti92.kicad_pcb and its schematic ti92.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).