

FireworksRobot
- Size
- 66 × 71 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 41
- Nets
- 45
- Pads
- 147
- Tracks, vias
- 305, 164
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 24 Jul 2020
- Updated
- 26 Sep 2021
Overview
FireworksRobot is an open-source printed circuit board by yutotnh, from the yutotnh/FireworksRobot repository on GitHub, published under the MIT licence. It is a 2-layer board of 66 × 71 mm with 41 parts on 45 nets, routed with 305 tracks and 164 vias.
It is built around the STM32F303K8T6, AP2210N-3.3TRG1 and AP2210N-5.0TRG1. Its parts include 12 resistors, 7 capacitors, 5 ICs, 5 diodes and 4 connectors. It belongs with the STM32 boards of this library.
Main components
3STM32F303K8T6
LQFP-32(7x7)-40℃~+85℃ 12bit 12bit 16KB 25 2V~3.6V 32 Bit 64KB 72MHz ARM Cortex-M4 Built-in FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)AP2210N-3.3TRG1
SOT-23-40℃~+125℃@(Tj) 1 13.2V 1uA 250mV@(300mA) 3.3V 300mA 75dB@(100Hz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-23 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAP2210N-5.0TRG1
SOT-23-40℃~+125℃@(Tj) 1 13.2V 1uA 300mA 400mV@(300mA) 5V 75dB@(100Hz) Fixed Over Current Protection、Over Temperature Protection、Reverse connection protection、Enable Positive SOT-23 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Parts
41| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 62 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2, R6, R7 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R10, R11, R12 |
| 2 | 0.1u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C5, C6 |
| 2 | 2.2k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4, R5 |
| 2 | 2.2u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C2, C4 |
| 2 | 200 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3, R8 |
| 2 | LED | LED_SMD:LED_0603_1608Metric_Castellated | D4, D5 |
| 2 | LED_RABG | LED_THT:LED_D5.0mm-4_RGB | D1, D3 |
| 2 | Motor_DC | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | M1, M2 |
| 2 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H3, H4 |
| 2 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2 |
| 1 | 1.0u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R9 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C7 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1 |
| 1 | AP2210N-3.3TRG1 | Package_TO_SOT_SMD:SOT-23W_Handsoldering | U1 |
| 1 | AP2210N-5.0TRG1 | Package_TO_SOT_SMD:SOT-23W_Handsoldering | U2 |
| 1 | Conn_01x03 | SamacSys_Parts:Conthrough_1x03_P2.54mm_Vertical | J1 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J4 |
| 1 | Conthrough | SamacSys_Parts:Conthrough_1x05_P2.54mm_Vertical | J2 |
| 1 | D_Schottky | Diode_SMD:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | Fuse | SamacSys_Parts:MF505 | F2 |
| 1 | Polyfuse | Fuse:Fuse_Littelfuse_395Series | F1 |
| 1 | SPS440 | SamacSys_Parts:SPS440 | IC1 |
| 1 | STM32F303K8 | Package_QFP:LQFP-32_7x7mm_P0.8mm | U3 |
| 1 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J3 |
| 1 | TB6612FNG | Package_SO:SSOP-24_5.3x8.2mm_P0.65mm | U4 |
Similar boards
- 2 layers39 × 58 mm

- 2 layers84.3 × 48.4 mm

- 8 layers163.5 × 123.5 mm

- 4 layers129 × 121 mm

MinyasX Combined
kunichiko/X68k-MinyasX
MinyasX は、Windows (AT互換機) 用の FDD を無改造で X68000 に接続して使えるようにするアダプタです。
232 parts2MIT - 2 layers100 × 81.3 mm

- 4 layers40 × 40 mm

CANBoard
corygrant/CANBoard
Hardware - CAN enabled small input / output expansion board. Switch panels, steering wheel buttons/knobs, etc.
83 parts53MIT - 2 layers104 × 43.3 mm

Serial snooper
can-caglar/Data-Logger-STM32
The Serial Snooper is a UART data logger with automatic baud rate detection, real-time data stamping and a command-line-interface for configuration, running on an STM32F3 microcontroller.
101 parts4 - 2 layers62 × 88 mm

Questions
How big is the FireworksRobot PCB?
It measures 66 × 71 mm and has 2 copper layers, 1.6 mm thick.
What parts does the FireworksRobot use?
41 parts, built around the STM32F303K8T6, AP2210N-3.3TRG1 and AP2210N-5.0TRG1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the FireworksRobot KiCad files?
From the yutotnh/FireworksRobot repository on GitHub, at the commit this page was made from: the board is FireworksRobot.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the FireworksRobot design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).