Skip to the content
2 layersPreamp, the printed circuit board in 3D

Design Files for a STM32-Based Underwater Acoustics data acquisition board for harbour porpoises

Copper layers
2
Thickness
1.6 mm
Parts
42
Nets
25
Pads
107
Tracks, vias
330, 13
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
9 Apr 2020
Updated
26 Apr 2021

Overview

Preamp is an open-source printed circuit board by ybabs, from the ybabs/PorpDAQ repository on GitHub, published under the MIT licence. It is a 2-layer board with 42 parts on 25 nets, routed with 330 tracks and 13 vias.

It is built around the LMH6643MA, LT1528CQ#PBF and SMA-J-P-H-ST-EM1. Its parts include 15 resistors, 14 capacitors, 5 ICs and 3 connectors. It belongs with the audio and music boards of this library.

Main components

3

README

README.md

PorpDAQ

STM32 Based design data acquisition recorder for harbour porpoises. The system is based on a 40dB bandpass preamplifier (90Khz - 150kHz). Records WAV file at a sampling rate of 400 KHz (V1) and 500 KHz (V2) and stores them to a microSD card. The preamplifier was designed using TI's filter designer tool. Preamp output is passed to a summing amplifier to keep signals within 0 - 3.3V with a 1.65V bias. There's a few iterations of the DAQ from the initial prototypes to improved designs.

PorpDAQ has been designed to fit within a small multirotor UAV so current design weighs only 18g. PorpDAQ computes a 1024 point RFFT of incoming hydrophone signals and transmits signals within 90 - 150KHz over a UART Interface

Rev 1 Board

The initial version of the DAQ was based on a STM32F746 chip and had a 400 KHz sample rate and a 12-bit ADC with a SD card write speed of about 20mbps.

Rev 2 Board

Rev 2 board comes with some improvements namely the the use of the STM32H743 chip, USB-C for power with the addition of a full speed interface. 500 KHz sample rate, SD Card write speed of ~35 Mbps with a 16-bit ADC and better SNR. Also slightly smaller footprint

This repository mostly contains :

  • Hardware designs for the both revisions (circuits were simulated in MultiSim and designs were made in UltiBoard and Kicad)
  • Designs for the different prototypes used.
  • A CM4-based design to integrate PorpDaq with a Pi4 Compute Module (WIP)
  • 3D designed case for the Rev 1 board
  • Low level drivers and firmware (bare-metal version and FreeRTOS version for Rev1 and FreeRTOS version for Rev2)

Note Rev2.1 now included as well.

  • 3.3V regulator on Rev 2 used a switcher and wasn't running in low noise mode (oops!) so 2.1 now uses a low noise ADP7156 3.3V regulator

Structure

  • Firmware: Contains Custom Board FreeRTOS firmware and STM32F7 discovery board FreeRTOS and bare-metal firmware. Also contains H747 Disco Board firmware. Please note bare-metal firmware currently has a UART TX bug preventing data from being transmmitted over the UART line.
  • Hardware: contains various designs and schematics for the board designs. Rev 1 design is named board_100pin while Rev 2 design is named h7_board.

Citation (Bibtex)

@article{Babatunde2020, doi = {10.3390/s20216064}, url = {https://doi.org/10.3390/s20216064}, year = {2020}, month = oct, publisher = {{MDPI} {AG}}, volume = {20}, number = {21}, pages = {6064}, author = {Daniel Babatunde and Simon Pomeroy and Paul Lepper and Ben Clark and Rebecca Walker}, title = {Autonomous Deployment of Underwater Acoustic Monitoring Devices Using an Unmanned Aerial Vehicle: The Flying Hydrophone}, journal = {Sensors} }

License

MIT License Copyright 2020 Daniel Babatunde

Parts

42
QtyValueFootprintReferences
4100pFCapacitor_SMD:C_0603_1608MetricC5, C6, C7, C8
4MountingHole_2.2mm_M2MountingHole:MountingHole_2.2mm_M2REF1, REF2, REF3, REF4
347uFCapacitor_Tantalum_SMD:CP_EIA-2012-15_AVX-PC11, C12, C13
2100kResistor_SMD:R_0603_1608MetricR12, R13
2100nfCapacitor_SMD:C_0603_1608MetricC3, C4
2187Resistor_SMD:R_0603_1608MetricR4, R9
22.49kResistor_SMD:R_0603_1608MetricR5, R10
250kResistor_SMD:R_0603_1608MetricR11, R14
2Conn_01x02_MaleConnector_PinHeader_1.00mm:PinHeader_1x02_P1.00mm_VerticalJ2, J3
2OPA659IDBVROPA659IDBVR:SOT95P280X145-5NU2, U3
1100nFCapacitor_SMD:C_0603_1608MetricC14
110kResistor_SMD:R_0603_1608MetricR3
110pFCapacitor_SMD:C_0603_1608MetricC9
11ufCapacitor_SMD:C_0603_1608MetricC1
1220uFCapacitor_Tantalum_SMD:CP_EIA-2012-15_AVX-PC2
1330Resistor_SMD:R_0603_1608MetricR15
134.8kResistor_SMD:R_0603_1608MetricR6
135.7kResistor_SMD:R_0603_1608MetricR1
144.2kResistor_SMD:R_0603_1608MetricR7
147ufCapacitor_Tantalum_SMD:CP_EIA-2012-15_AVX-PC10
16.34kResistor_SMD:R_0603_1608MetricR8
166.5kResistor_SMD:R_0603_1608MetricR2
1LMH6643MALMH6643MA:SOIC127P600X175-8NU4
1LT1528CQLT1528CQ:DDPAK-5_QU5
1SMA-J-P-H-ST-EM1SMA-J-P-H-ST-EM1:SMA-J-P-H-ST-EM1J1
1Screw_Terminal_01x02Connector_AMASS:AMASS_XT30PW-M_1x02_P2.50mm_HorizontalBattery1
1TLE2426xDPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU1

More from ybabs/PorpDAQ

6
  • 4 layers76.3 × 54.3 mmCM4, the printed circuit board in 3D

    CM4

    ybabs/PorpDAQ

    Design Files for a STM32-Based Underwater Acoustics data acquisition board for harbour porpoises

    113 parts6MIT
  • 2 layers85.9 × 64.9 mmStm32 board, the printed circuit board in 3D

    Stm32 board

    ybabs/PorpDAQ

    Design Files for a STM32-Based Underwater Acoustics data acquisition board for harbour porpoises

    101 parts6MIT
  • 4 layers77 × 60 mmHydrophone stm32 board, the printed circuit board in 3D

    Hydrophone stm32 board

    ybabs/PorpDAQ

    Design Files for a STM32-Based Underwater Acoustics data acquisition board for harbour porpoises

    98 parts6MIT
  • 4 layers68.2 × 41.6 mmCM4, the printed circuit board in 3D

    CM4

    ybabs/PorpDAQ

    Design Files for a STM32-Based Underwater Acoustics data acquisition board for harbour porpoises

    89 parts6MIT
  • 4 layers68.2 × 41.6 mmCM4, the printed circuit board in 3D

    CM4

    ybabs/PorpDAQ

    Design Files for a STM32-Based Underwater Acoustics data acquisition board for harbour porpoises

    89 parts6MIT
  • 4 layers69.8 × 45.7 mmF7 100pin, the printed circuit board in 3D

    F7 100pin

    ybabs/PorpDAQ

    Design Files for a STM32-Based Underwater Acoustics data acquisition board for harbour porpoises

    77 parts6MIT

Similar boards

  • 2 layers103.6 × 61.7 mmBoard ESP MikroBus V1, the printed circuit board in 3D

    Board ESP MikroBus V1

    thingsat/tinygs_2g4station

    HW and FW of a TinyGS 2.4 GHz LoRa ground station https://tinygs.com/

    26 parts30
  • 8 layers126 × 117 mmDemo board, the printed circuit board in 3D

    Demo board

    azonenberg/electronics-training

    Training materials for classes etc

    311 parts15
  • 4 layers68.6 × 58.4 mmPlant combined, the printed circuit board in 3D

    Plant combined

    theblinkingman/plant-waterer

    TDR sensor to water a plant automatically

    74 parts9
  • 4 layers127 × 101.6 mmS Band Transceiver, the printed circuit board in 3D

    S Band Transceiver

    tkeller12/openEPR

    Open-Source EPR Spectrometer

    224 parts1MIT
  • 6 layers40 × 15 mmMiniDAQ, the printed circuit board in 3D

    MiniDAQ

    Aharoni-Lab/MiniDAQ

    Simplified bare bones DAQ for Miniscopes and Minicams

    162 parts
  • 2 layers65 × 23.5 mmPicise, the printed circuit board in 3D

    Picise

    ckuhtz/picise

    Prototype for a time / location GNSS accessory for a Raspberry Pi 40-pin GPIO.

    39 partsCC-BY-SA-4.0
  • 2 layers31 × 23.5 mmExpansion board RFM95, the printed circuit board in 3D

    Expansion board RFM95

    EvoLuvDaP/Expansion_board_RFM95

    A single-layer PCB design suitable for educational testing purposes.

    5 parts
  • 2 layers78.8 × 85.4 mmISS VP2 Datalog, the printed circuit board in 3D

    ISS VP2 Datalog

    fr4sw/ISS_VP2_Datalog

    Datalogger pour ISS_V2 et Meshtastic

    36 partsGPL-2.0

Questions

What parts does the Preamp use?

42 parts, built around the LMH6643MA, LT1528CQ#PBF and SMA-J-P-H-ST-EM1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Preamp KiCad files?

From the ybabs/PorpDAQ repository on GitHub, at the commit this page was made from: the board is Hardware/preamp_v2/preamp.kicad_pcb and its schematic CM4 Design/CM4/CM4.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Preamp design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).