

Baseboard
Board fitting into wall switch, support for 1Wire, quadrature encoder, and much more. RS-485
- Size
- 50 × 44 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 82
- Nets
- 76
- Pads
- 308
- Tracks, vias
- 1,009, 123
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 15 Mar 2021
- Updated
- 31 Mar 2021
Overview
Baseboard is an open-source printed circuit board by xtompok, from the xtompok/home_automation_switchboard repository on GitHub, published under the MIT licence. It is a 2-layer board of 50 × 44 mm with 82 parts on 76 nets, routed with 1,009 tracks and 123 vias.
It is built around the SN65HVD3082EDR, BME280 and MP2451DJ, with the W25Q128JVSIQ, SCD30 and 74HC14 among its other parts. Its parts include 25 resistors, 22 capacitors, 11 connectors, 7 ICs and 7 diodes. It belongs with the interfaces and adapters and home automation and IoT boards and the STM32 boards of this library.
Main components
9SN65HVD3082EDR
SOP-8-40℃~+85℃ 1 1 12Mbps 3.3V 32 425uA Enable shutdown、Overcurrent Protection、Thermal shutdown protection、Tx/Rx enable Half-Duplex Transceiver ±8kV SOP-8 RS-485 / RS-422 ICs ROHSJSMSEMIRS-485 / RS-422 ICsBME280
LGA-8(2.5x2.5)-40℃~+85℃ 0%RH~100%RH 1.71V~3.6V 1.8uA 16bit I2C、SPI ±0.5℃ ±3%RH LGA-8(2.5x2.5) Temperature and Humidity Sensor ROHSBoschTemperature And Humidity SensorMP2451DJ
TSOT-23-6-40℃~+125℃ 1 130uA 2MHz 3.3V~36V Adjustable Buck Buck Built-in TSOT-23-6 DC-DC Converters ROHSMonolithic Power SystemsDC-DC ConvertersW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSCD30
-0ppm~40000ppm 0℃~+50℃ 19mA 23mm 3.3V~5.5V 35mm 7mm Carbon dioxide Multi-gas detection capability UART、I2C、PWM ±3% - Gas Sensors ROHSSensirionGas Sensors74HC14
SOP-14-40℃~+85℃ 1.9V、3.98V、4.4V、5.48V、5.9V 100mV、260mV、260mV 20uA 25ns@4.5V,50pF 2V~6V 6 74HC Noise suppression function Schmitt trigger SOP-14 Inverters ROHSJSMSEMIInvertersXC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsB5819W
SOD-123-55℃~+125℃ 1.5A 1mA@40V 25A 40V 600mV@1A Standalone SOD-123 Schottky Diodes ROHSMDDSchottky DiodesNSMD020-30V
1206-40℃~+85℃ 0.9mm 1.8mm 100A 2.7Ω 200mA 3.5mm 30V 350mΩ 460mA 600mW 1206 Resettable Fuses ROHS台湾陆海Resettable Fuses
README
README.mdhome_automation_switchboard
Board fitting into wall switch, support for 1Wire, quadrature encoder, and much more. RS-485
Parts
82| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100k | Resistor_SMD:R_0603_1608Metric | R22, R32, R33, R36, R38, R39, R48, R49 |
| 6 | 100n | Capacitor_SMD:C_0603_1608Metric | C3, C11, C12, C18, C21, C23 |
| 6 | 47n | Capacitor_SMD:C_0603_1608Metric | C14, C15, C19, C20, C24, C25 |
| 5 | 1u | Capacitor_SMD:C_0603_1608Metric | C1, C16, C17, C27, C28 |
| 4 | 330R | Resistor_SMD:R_0603_1608Metric | R1, R2, R4, R6 |
| 4 | 4k7 | Resistor_SMD:R_0603_1608Metric | R23, R24, R25, R44 |
| 4 | R | Resistor_SMD:R_0603_1608Metric | R37, R47, R50, R51 |
| 3 | 15k | Resistor_SMD:R_0603_1608Metric | R3, R5, R46 |
| 3 | 330R | Resistor_SMD:R_Array_Convex_4x0603 | RN1, RN3, RN4 |
| 2 | 27p | Capacitor_SMD:C_0603_1608Metric | C5, C7 |
| 2 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | B5819W | Diode_SMD:D_SOD-123 | D11, D19 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C22 |
| 1 | 10uH | Inductor_SMD:L_Abracon_ASPI-3012S | L1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 1Wire | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J8 |
| 1 | 33p | Capacitor_SMD:C_0603_1608Metric | C26 |
| 1 | 74HC14 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U4 |
| 1 | 8MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | ADC | Connector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_Vertical | J3 |
| 1 | BME280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | ENC1 | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J7 |
| 1 | ENC2 | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J9 |
| 1 | GPIO | Connector_JST:JST_PH_B8B-PH-K_1x08_P2.00mm_Vertical | J13 |
| 1 | I2C | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J4 |
| 1 | LED_EN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | L_12V | LED_SMD:LED_0603_1608Metric | D18 |
| 1 | L_RX | LED_SMD:LED_0603_1608Metric | D17 |
| 1 | L_TX | LED_SMD:LED_0603_1608Metric | D16 |
| 1 | L_U1 | LED_SMD:LED_0603_1608Metric | D14 |
| 1 | L_U2 | LED_SMD:LED_0603_1608Metric | D15 |
| 1 | MP2451 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | POWER+RS-485 | LED_driver:PTSA_1.5_4-3.5-Z-1985218 | J5 |
| 1 | PROG | DR_Footprints:SIP-5 | J2 |
| 1 | SCD30 | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J12 |
| 1 | SN65HVD3082EDR | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | STM32G0_LQFP48 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | USART2 | Connector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_Vertical | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U1 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | U7 |
| 1 | nSMD020-30V | Fuse:Fuse_1206_3216Metric | F1 |
Similar boards
- 2 layers40 × 70 mm

- 4 layers107.5 × 102.5 mm

- 2 layers35 × 35 mm

- 2 layers72 × 47 mm

- 2 layers100 × 95 mm

Controller
Doc-Raptor/dragon_controller
32bit 3d-printer controller board for 3d printers from china with the anet-stlye controller-board
88 parts3 - 2 layers

Afork kicad parts
CapnKernel/afork-kicad-parts
A collection of symbols and footprints that I know to work well in KiCad
13 parts - 2 layers32 × 96 mm

- 2 layers49 × 59 mm

Questions
How big is the Baseboard PCB?
It measures 50 × 44 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Baseboard use?
82 parts, built around the SN65HVD3082EDR, BME280, MP2451DJ and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Baseboard KiCad files?
From the xtompok/home_automation_switchboard repository on GitHub, at the commit this page was made from: the board is hw/baseboard/baseboard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Baseboard design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).