2 layers101.6 × 95.3 mm
2 679 PCB
wszeto9/2_679_PCB
PCB Project for 2.679 which is then used in my 2.007 Competition Robot
128 parts1
2 layers98.4 × 99.5 mm
Arduino usb c
wszeto9/2_679_PCB1PCB Project for 2.679 which is then used in my 2.007 Competition Robot
- Size
- 98.4 × 99.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 161
- Nets
- 69
- Pads
- 937
- Tracks, vias
- 1,710, 227
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 16 Mar 2022
- Updated
- 10 Jul 2022
Overview
Arduino usb c is an open-source printed circuit board by wszeto9, from the wszeto9/2_679_PCB repository on GitHub. It is a 2-layer board of 98.4 × 99.5 mm with 161 parts on 69 nets, routed with 1,710 tracks and 227 vias.
It is built around the ATMEGA328P-AU, CH340C and OP07, with the AMS1117-5.0 and AON6558 among its other parts. Its parts include 45 resistors, 38 capacitors, 18 connectors, 16 ICs and 13 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5
ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
OP07
SOP-8-20℃~+85℃ -22V~-3V、3V~22V 1 1.8nA 1.8uV/℃ 10nV/√Hz@1kHz 120dB 15pA/℃ 170V/ms 2.7mA 22V 500kHz 60uV 800pA SOP-8 Operational Amplifier ROHSSlkorOperational Amplifier
AMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAON6558
DFN-8(5x6)-55℃~+150℃ 1 N-channel 1.128nF 1.8V 16.2nC@10V 24W 30A 30V 4.2mΩ@10V 435pF 59pF N-Channel DFN-8(5x6) MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
README
Arduino_USB_C/arduino_usb_c/README.md2.007 Power Distribution Board
Battery protection circuit for 2.007 "Legacy" Robotics Competiton @ MIT, Spring 2022
Features:
- 20A socketable fused input
- Reverse polarity protection
- Voltage Monitoring components to prevent overdischarging of batteries
- Black colored Arduino Nano for looks
- Op-Amp breakout board for additional gain on current sensors
PCBA
Top
Parts
161| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 1K | Resistor_SMD:R_0402_1005Metric | R1, R1, R1, R1, R2, R2, R2, R2, R3, R3, R3, R3, R4, R4, R4, R4 +5 |
| 16 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C1, C1, C1, C2, C2, C2, C2, C5, C5, C5, C5, C9, C9, C9, C9 |
| 14 | 1uF | Capacitor_SMD:C_0603_1608Metric | C4, C4, C4, C4, C6, C6, C6, C7, C7, C7, C10, C10, C10, C10 |
| 10 | 10k | Resistor_SMD:R_0402_1005Metric | R8, R10, R10, R10, R11, R11, R11, R12, R12, R12 |
| 9 | LED | LED_SMD:LED_0603_1608Metric | D1, D1, D1, D1, D3, D3, D3, D3, D4 |
| 8 | 4.7uF 16V Tant | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I | C3, C3, C3, C3, C8, C8, C8, C8 |
| 8 | 5.1K 1% | Resistor_SMD:R_0402_1005Metric | R5, R5, R5, R5, R6, R6, R6, R6 |
| 6 | Conn_01x03_Male | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J7, J7, J7, J8, J8, J8 |
| 4 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3, U3, U3, U3 |
| 4 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1, U1, U1, U1 |
| 4 | Arduino_Nano_v3.x | Module:Arduino_Nano | A1, A1, A1, A1 |
| 4 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U2, U2, U2, U2 |
| 4 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2, J2, J2, J2 |
| 4 | Crystal_GND2_Small | Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y1, Y1, Y1, Y1 |
| 4 | D_Schottky | Diode_SMD:D_SMA | D2, D2, D2, D2 |
| 4 | SW_SPST | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1, SW1, SW1, SW1 |
| 4 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_Palconn_UTC16-G | J1, J1, J1, J1 |
| 3 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R13, R13, R13 |
| 3 | 40k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R14, R14, R14 |
| 3 | OP07 | Package_DIP:DIP-8_W7.62mm_Socket | U5, U5, U5 |
| 2 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J3, J4 |
| 1 | AON6558 | Package_DFN_QFN:DFN-8-1EP_6x5mm_P1.27mm_EP4x4mm | U4 |
| 1 | Conn_01x03_Male | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J5 |
| 1 | Conn_02x03_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_Horizontal | J6 |
| 1 | Fuse | Fuse:Fuseholder_Blade_Mini_Keystone_3568 | F1 |
| 1 | SW_SPST | Switch:M2012SS2W13 | SW2 |
| 1 | Voltmeter_DC | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | MES1 |
The 145 most common of 161 parts.
More from wszeto9/2_679_PCB
1Similar boards
- 4 layers62 × 60.8 mm
Pcbcax
7bwiiza/Robot-creation
Uni project of a 3D model of a 5dof robot using Solidedge and motor control using KiCAD and MATLAB
58 parts - 2 layers52 × 70 mm
Taptempo smd
Valleeh/taptempo-box
Tap-tempo box: MIDI clock + switched tempo outputs, ATmega328P, perfboard and JLCPCB SMD versions, 3D-printed enclosure
45 partsMIT - 2 layers256 × 121 mm
Forte PA Deck
SP6GK/Forte-600-HF-RF-Amplifier
Project of 600 W LDMOS amlifier based on 2xMRF300.
170 parts17GPL-3.0 - 2 layers100 × 82 mm
TXRX Relay Board
SP6GK/TXRX_Relay_Board
A PCB for switching the signal path between RX and TX in a high-power HF amplifier, such as the Forte 600. It includes RX/TX relays, an input SWR bridge, and analog input over power protection.
80 parts2GPL-3.0 - 2 layers114 × 95 mm
- 2 layers139.7 × 88.9 mm
- 4 layers62.9 × 88.6 mm
Bit block
Citrullin/Sovereign_Bunny_Stack
From web 3 unicorn fantasy to federated web 2.5 reality.
169 parts4 - 2 layers54 × 29 mm
Webasto heater controller
matty337s/Webasto-Heater-WBUS-Controller
Controller for webasto heater used in vehicles such as Land Rover Discovery 3. Used to turn on and off heater using ATTINY microcontroller, with inputs for USB, ignition and low-beam.
39 parts3GPL-3.0
Questions
How big is the Arduino usb c PCB?
It measures 98.4 × 99.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Arduino usb c use?
161 parts, built around the ATMEGA328P-AU, CH340C, OP07 and AMS1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Arduino usb c KiCad files?
From the wszeto9/2_679_PCB repository on GitHub, at the commit this page was made from: the board is Arduino_USB_C/arduino_usb_c/arduino_usb_c.kicad_pcb and its schematic 2_679_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Arduino usb c design in my own project?
Its repository states no licence, so its author keeps all rights: ask wszeto9 before reusing the design.