Skip to the content
2 layers39 × 39 mmTransmitter, the printed circuit board in 3D

A simple MIPI CSI-2 extender with 4-lane support through HDMI cable

Size
39 × 39 mm
Copper layers
2
Thickness
1.6 mm
Parts
18
Nets
22
Pads
98
Tracks, vias
181, 62
Pours
5
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
2 Mar 2025
Updated
3 Mar 2025

Overview

Transmitter is an open-source printed circuit board by will127534, from the will127534/CSI-2-FourLane-HDMI-Extender repository on GitHub, published under the MIT licence. It is a 2-layer board of 39 × 39 mm with 18 parts on 22 nets, routed with 181 tracks and 62 vias.

It is built around the TPSM82902SISR. Its parts include 7 connectors, 3 capacitors, 2 resistors and 1 IC. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

CSI-2-FourLane-HDMI-Extender

A simple MIPI CSI-2 extender with 4-lane support through HDMI cable

Hardware

Technically, this isn’t supposed to work, but it kind of does. It relies on HDMI cables with Ethernet support to provide the fifth differential pair needed to transmit 4-lane MIPI signals through the HDMI cable.

The board is very simple. The receiver can either use the 3.3V from the FPC cable or an external power input to supply the HDMI connector’s power output. The HDMI connector location matches the USB connector on the Raspberry Pi 5 to simplify case design.

The transmitter board has a DC-DC step-down converter with a 3.3V output and a bypass option to power camera boards. For the StarlightEye (which needs a 5V input), there is also a connector that taps into the HDMI power input to supply power—this could also power something else, like an LED light source. Additionally, there is a QWIIC connector for sideband communication. Finally, the board’s form factor includes a cutout for the OneInchEye 2.0.

Notes

This project came about because GMSL2 was too difficult to implement, and I needed something to extend my 4-lane MIPI cameras. If you’re reading this, you probably already know there are a few HDMI extender boards for MIPI cameras out there. However, most only support 2-lane MIPI, while I specifically needed 4-lane MIPI.

Where’s the catch? The standard HDMI cable only has four high-speed differential pairs, so that’s typically not enough for 4-lane MIPI (which requires 4 data pairs + 1 clock pair). However, HDMI includes an extension standard that reuses the HPD and UTILITY pins on the connector for a fifth differential pair called HEAC. This pair is meant for a bi-directional higher-speed sideband signal for Ethernet or Audio. Spec-wise, it doesn't have to carry signals as high-speed as the main video data. However, from a manufacturing standpoint, it’s often just as capable, because many manufacturers use the same type of differential pair cable for the fifth pair. (See this teardown video by ChargerLab as an example.)

For testing, I used the Cable Matters 2-Pack Ultra Thin HDMI Cable series; the 6-ft version is the maximum length that can run both the OneInchEye and StarlightEye at 1440 Mbps/lane with 4-lane MIPI.

Note: If you are using my IMX585 driver, you must lower the link speed from 1782 Mbps/lane to 1440 Mbps/lane by changing this line to 0x03.

Lastly, I did try using MIPI redrivers and retimers from Ti and Diodes. The receiver board was originally designed with an active redriver/retimer (both parts are conveniently pin-to-pin compatible). However, due to the board’s pin layout, the differential pairs would need a polarity swap, and TI’s retimer wouldn’t work, even with this register configured. As for the redriver, for some reason I couldn’t get it to work well with a 6-ft cable—only with a very short HDMI cable. The redriver is polarity-invariant, but even after playing around with the different tuning options, it just didn’t seem to work reliably. Suggestions are welcome in the issues/comments section.

Footnotes

  • Gerber, BOM, and CPL files for JLCPCB are under /Gerber and /bom in each Transmitter and Receiver board folder.
  • Interactive BOM for Receiver (provided by InteractiveHtmlBom)
  • Interactive BOM for Transmitter (provided by InteractiveHtmlBom)
  • Yes It still supports 2-lane MIPI cameras (tested with the IMX708 Raspberry Pi Camera V3).
  • I have almost no intention of selling this on Tindie, because I can already imagine users who don’t fully understand the details running into troubles and complaining about it.
  • @VoeGalore made 3D-printable cases for using the transmitter board with starlighteye(IMX585), oneincheye(IMX283), and Camera Module V3. STL files are under /case-STL in each folders. Additional hardware might be needed (M2x16 screws, M2x6 screws, M2 threaded insert, 1/4-20 threaded insert).

Parts

18
QtyValueFootprintReferences
4MountingHoleMountingHole:MountingHole_2.2mm_M2H1, H2, H3, H4
3Conn_01x02_ShieldedConnector_Molex:Molex_PicoBlade_53398-0271_1x02-1MP_P1.25mm_VerticalJ5, J6, J7
2Conn_01x04_ShieldedConnector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ3, J4
110uFCapacitor_SMD:C_0402_1005MetricC3
110uFCapacitor_SMD:C_0805_2012MetricC1
122uFCapacitor_SMD:C_0805_2012MetricC2
140.2KResistor_SMD:R_0402_1005MetricR1
1Conn_01x22_ShieldedConnector_FFC-FPC:Hirose_FH12-22S-0.5SH_1x22-1MP_P0.50mm_HorizontalJ1
1DNCResistor_SMD:R_0402_1005MetricR2
1HDMI_A_1.4Connector_Video:HDMI_A_Molex_208658-1001_HorizontalJ2
1SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1
1TPSM82902SISRfootprints:uSIP11_SIS_TEXU2

More from will127534/CSI-2-FourLane-HDMI-Extender

1
  • 4 layers27 × 56 mmReceiver, the printed circuit board in 3D

    Receiver

    will127534/CSI-2-FourLane-HDMI-Extender

    A simple MIPI CSI-2 extender with 4-lane support through HDMI cable

    9 parts15MIT

Similar boards

  • 6 layers89.4 × 69 mmPi hat, the printed circuit board in 3D

    Pi hat

    ApotheoTech/APT-V01-FMC

    GPIO FMC card, Schematics and PCB

    132 parts4
  • 4 layers74.3 × 148.8 mmSeniorDesign, the printed circuit board in 3D

    SeniorDesign

    mikemederos/STM32_PCB

    STM32F103C8-based PCB used to calculate 3-phase AC impedance to aid in detection of high-impedance faults.

    139 parts
  • 6 layers12v smps, the printed circuit board in 3D

    12v smps

    charlieh0tel/ee_stuff

    7 partsBSD-3-Clause
  • 2 layers27.9 × 16.5 mmPowerSSO-24 breakout, the printed circuit board in 3D

    PowerSSO-24 breakout

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    18 parts1.2k
  • 2 layers42.7 × 13.7 mmStm32-mini12864, the printed circuit board in 3D

    Stm32-mini12864

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    18 parts1.1kGPL-3.0
  • 2 layers41.2 × 46.6 mmThumb cluster left, the printed circuit board in 3D

    Thumb cluster left

    JesusFreke/lalboard

    A 3D-printed keyboard inspired by the DataHand

    18 parts993
  • 2 layers44 × 51.3 mm4272MAVcoder R4, the printed circuit board in 3D

    4272MAVcoder R4

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    18 parts915
  • 2 layers28.3 × 14.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    18 parts716GPL-3.0

Questions

How big is the Transmitter PCB?

It measures 39 × 39 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Transmitter use?

18 parts, built around the TPSM82902SISR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Transmitter KiCad files?

From the will127534/CSI-2-FourLane-HDMI-Extender repository on GitHub, at the commit this page was made from: the board is Transmitter/Transmitter.kicad_pcb and its schematic Receiver/Receiver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Transmitter design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).