

MotoHUD
KiCad Schematic and PCB for motoHUD (https://github.com/wiciu15/motoHUDini)
- Size
- 128 × 55 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 121
- Nets
- 88
- Pads
- 328
- Tracks, vias
- 1,118, 133
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Jul 2019
- Updated
- 26 Nov 2019
Overview
MotoHUD is an open-source printed circuit board by wiciu15, from the wiciu15/motoHUDsch repository on GitHub. It is a 2-layer board of 128 × 55 mm with 121 parts on 88 nets, routed with 1,118 tracks and 133 vias.
It is built around the LM2904DT, MCP16301-E/CH and M95320-WMN6P, with the 1N4148W-7-F-CN, LFXTAL009678 and STPS1L40A among its other parts. Its parts include 45 resistors, 18 capacitors, 10 diodes, 9 connectors and 6 ICs. It belongs with the STM32 boards of this library.
Main components
6LM2904DT
SOIC-8-40℃~+125℃ 1.1MHz 10pA/℃ 2 20nA 2mV 2nA 30V 3V~30V 40mA 55nV/√Hz@1kHz 600V/ms 700uA 7uV/℃ 85dB SOIC-8 Operational Amplifier ROHSSTMicroelectronicsOperational AmplifierMCP16301-E/CH
SOT-23-6-40℃~+125℃ 1 2V~15V 2mA 4V~30V 500kHz 600mA Adjustable Buck Buck Built-in No SOT-23-6 DC-DC Converters ROHSMicrochip TechnologyDC-DC ConvertersM95320-WMN6P
SOIC-8-40℃~+85℃ 2.5V~5.5V 200 Years 32Kbit 4,000,000 Cycles 5ms Hardware write protection function、Software write protection function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function、Built-in write enable latch (WEL) SPI SOIC-8 EEPROM ROHSSTMicroelectronicsEEPROM1N4148W-7-F-CN
SOD-123SOD-123 Switching Diodes ROHSChipNoboSwitching DiodesLFXTAL009678
SMD3215-2P-40℃~+85℃ 12.5pF 32.768kHz 70kΩ Crystal Oscillator ±20ppm SMD3215-2P Crystals ROHSIQDCrystalsSTPS1L40A
SMA(DO-214AC)-40℃~+175℃ 1 Independent 1A 35uA@40V 40V 500mV@1A 60A SMA(DO-214AC) Schottky Diodes ROHSSTMicroelectronicsSchottky Diodes
README
README.mdmotoHUDsch
KiCad Schematic and PCB for STM32F103-based motorcycle digital instrument cluster with 2.8in ILI9341 LCD and X27.168 stepper motor for dial gauge indicator.
Firmware - https://github.com/wiciu15/motoHUDini
Enclosure - https://github.com/wiciu15/motoHUDencl
Demo video - https://youtu.be/awKXkiaZZUE



Rev1 has problems with thermals on 5V regulator, ADC accuracy and other brain farts like bad footprint or silkscreen marking
Rev2 comes with fixes and some new features like button switches. It is not perfect however :/
Rev2 need some mods to work properly:
-U2 needs to be powered from a 5V rail or changed to a rail-to-rail dual opAmp in same package (LM2903 is not rail-to-rail unfortunately)
-C25 and C21 need a parallel resistor to discharge them (100k-200k ohm range)
-startup current is too high and destroys fuses immidately - I switched F1 fuse with a 1206 2,2ohm resistor
If you don't have/like KiCAD there are schematic PDFs and gerber files.
Parts
121| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R15, R21, R29, R41, R43, R45, R51, R52, R55, R211 |
| 6 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R11, R27, R28, R31, R54, R61 |
| 4 | 0,1u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C13, C23, C24, C34 |
| 4 | 0R | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R16, R17, R32, R62 |
| 4 | 100R | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R33, R34, R35, R36 |
| 4 | 10u 16v | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C12, C14, C15, C17 |
| 4 | 1N4148W-7-F | Diode_SMD:D_SOD-123 | D1, D2, D3, D5 |
| 4 | 20p | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C30, C31, C32, C33 |
| 4 | 22u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C18, C21, C22, C25 |
| 4 | 39R | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R63, R64, R65, R66 |
| 4 | BCKLED | LED_SMD:LED_1206_3216Metric | D6, D7, D8, D9 |
| 3 | 1,5k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R14, R73, R74 |
| 3 | 3k3 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R42, R44, R46 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R53, R210 |
| 2 | 22R | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R71, R72 |
| 2 | 2N7002KQ-13 | motoHUD:SOT-23 | Q1, Q2 |
| 2 | 5,1k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R24, R25 |
| 2 | 7,6k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R22, R23 |
| 2 | LM2904DT | Package_SO:SO-8_5.3x6.2mm_P1.27mm | U2, U3 |
| 2 | TACTM-613N-F | motoHUD:TACTM-613N-F | SW1, SW2 |
| 1 | 100u | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C16 |
| 1 | 2,2k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R26 |
| 1 | 2,2u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C11 |
| 1 | 22k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R12 |
| 1 | 3v3 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP2 |
| 1 | 51,1k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R13 |
| 1 | 5V | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP6 |
| 1 | AZ1117-3.3 | motoHUD:SOT-223 | U4 |
| 1 | BCKL_CAP | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP5 |
| 1 | BCKL_V | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP14 |
| 1 | BOOST | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP13 |
| 1 | CS2 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP23 |
| 1 | DLG-0403-220 | motoHUD:DLG-0403-220 | L1 |
| 1 | ESKA FUSE 0805-FF PW 0A5 | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | HALL | Connector_JST:JST_XH_B03B-XH-A_1x03_P2.50mm_Vertical | J4 |
| 1 | HC49USM-FF3F18-8M | Crystal:Crystal_SMD_HC49-SD_HandSoldering | Y1 |
| 1 | HIBEAM | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP19 |
| 1 | HIBEAM12 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP20 |
| 1 | ICSP | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | LCD Connector | motoHUD:ILI9341FFC | J9 |
| 1 | LCDCAP | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP27 |
| 1 | LCDV | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP30 |
| 1 | LEDSTATUS | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D10 |
| 1 | LFXTAL009678 | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | M95320-WMN6P | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | MCP16301 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | MISO2 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP33 |
| 1 | MOSI2 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP32 |
| 1 | PA0 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP7 |
| 1 | PA1 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP8 |
| 1 | POWER | Connector_JST:JST_XH_B03B-XH-A_1x03_P2.50mm_Vertical | J1 |
| 1 | RPMA | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP12 |
| 1 | RPMC | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP15 |
| 1 | RPMD | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP16 |
| 1 | SCK2 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP31 |
| 1 | SIGNAL | Connector_JST:JST_XH_B03B-XH-A_1x03_P2.50mm_Vertical | J6 |
| 1 | SIG_RPM | Connector_JST:JST_XH_B02B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | STPS1L40A | Diode_SMD:D_SMA_Handsoldering | D4 |
| 1 | TEMP1 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP10 |
| 1 | TEMP2 | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP11 |
| 1 | THERM1 | Connector_JST:JST_XH_B02B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | THERM2 | Connector_JST:JST_XH_B02B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | USB_B_Mini | Connector_USB:USB_Mini-B_Lumberg_2486_01_Horizontal | J7 |
| 1 | USB_ID | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP9 |
| 1 | VEL | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP1 |
| 1 | V_IGN | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP4 |
| 1 | V_RTC | motoHUD:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP3 |
| 1 | X27 168 | motoHUD:X27-168 | M1 |
Similar boards
- 4 layers130 × 100 mm

- 2 layers30.5 × 19.1 mm

- 2 layers79 × 89 mm

Bms v1
azerimaker/BMS_3-5S
3-5S Battery Management System based on TI bq76920 IC and MSP430 uC.
175 parts22 - 2 layers200 × 100 mm

Mobo
opulo-inc/lumenpnp-archive
This repository is a public archive of the LumenPnP Pick and Place (formerly Index) source material from the beginning in mid-2020 until May 2022. The current source can be found at https://github.com/opulo-inc/lumenpnp
88 parts6GPL-3.0 - 2 layers100 × 67 mm

Led controller
markus-k/led-controller-hardware
KiCAD schematics and design files for my LED controller.
91 parts5 - 2 layers83.8 × 80 mm

- 4 layers100 × 27 mm

Props board v3
ephemeridis/props_board
ESP32 based control board for costumes and props featuring USB PD enabled charging
188 partsGPL-3.0 - 2 layers53.3 × 64.4 mm

Wifi homesensor
masterfoxxhu/wifi_homesensor
Quick and dirty ESP8266 based thermo and humidity meter for ESPhome
33 partsGPL-3.0
Questions
How big is the MotoHUD PCB?
It measures 128 × 55 mm and has 2 copper layers, 1.6 mm thick.
What parts does the MotoHUD use?
121 parts, built around the LM2904DT, MCP16301-E/CH, M95320-WMN6P and 1N4148W-7-F-CN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the MotoHUD KiCad files?
From the wiciu15/motoHUDsch repository on GitHub, at the commit this page was made from: the board is motoHUD.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the MotoHUD design in my own project?
Its repository states no licence, so its author keeps all rights: ask wiciu15 before reusing the design.