
Jazzhands key
wearpants/jazzhands-hardware
A small multi-PCB handheld keyboard for chording style input.

A small multi-PCB handheld keyboard for chording style input.
Jazzhands main is an open-source printed circuit board by wearpants, from the wearpants/jazzhands-hardware repository on GitHub. It is a 2-layer board of 64.9 × 33 mm with 44 parts on 56 nets, routed with 252 tracks and 24 vias.
It is built around the LSM6DSO. Its parts include 16 connectors, 6 resistors, 4 capacitors, 4 ICs and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
A small multi-PCB handheld keyboard for chording style input.
The main "brains" PCB, which accepts a nice!nano controller.
It exposes connection points with Molex Pico EZMate connectors for 5 key PCBs, and a 3-pin Molex Pico EZMate connector for use with the power-reset daughterboard PCB.
An untested IMU is also on the main PCB, for future use.
A small single key PCB with Molex Pico EZMate connector, Kailh hotswap socket, and mounting holes for possible assembly. One mounting hole "wing" is breakaway, as needed.
A small daughterboard PCB that contains a reset button and power switch, allowing those two components to be placed elsewhere in a case
See the wearpants/jazzhands-zmk-config repo for firmware for the main PCB with ZMK.
It's possible to hack the current main PCB to also support a digital hall-effect sensor like the DRV5023 for use in a handheld "switchless design" using magnets only for activation in a glove.
All three PCBs can be produced by grabbing the generated files from the Actions tab and uploading to JLC, including partial assembly for the main PCB using JLC's PCBA service.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | Conn_01x02 | Connector_Molex:Molex_Pico-EZmate_78171-0002_1x02-1MP_P1.20mm_Vertical | J1, J2, J3, J4, J5, J9, J10, J11, J12, J13 |
| 8 | MountingHole | MountingHole:MountingHole_2.2mm_M2_Pad | H1, H2, H3, H4, H5, H6, H7, H8 |
| 4 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4 |
| 4 | 22 | Resistor_SMD:R_0603_1608Metric | R2, R3, R5, R6 |
| 2 | 68 | Resistor_SMD:R_0603_1608Metric | R1, R4 |
| 2 | BAT+ | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J7, J14 |
| 2 | BAT- | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J8, J15 |
| 2 | LED_ABGR | LED_SMD:LED_RGB_Wuerth-PLCC4_3.2x2.8mm_150141M173100 | D1, D2 |
| 2 | LSM6DSO | main:PQFN50P250X300X86-14N | U2, U4 |
| 2 | Power/Reset | Connector_Molex:Molex_Pico-EZmate_78171-0003_1x03-1MP_P1.20mm_Vertical | J6, J16 |
| 2 | ProMicro | Keebio-Parts:ArduinoProMicro | U1, U3 |
The 40 most common of 44 parts.

wearpants/jazzhands-hardware
A small multi-PCB handheld keyboard for chording style input.

wearpants/jazzhands-hardware
A small multi-PCB handheld keyboard for chording style input.


DimitriOnLSD/imu-rc
Gesture-based RC car controller using ESP32-S3, BLE, LSM6DSO IMU, OLED display, and LiPo battery with USB-C charging.


aweeri/Control-Avionics-RP2350
Control Avionics RP2350 [CARP] is a compact system designed specifically for operating small scale sounding rockets.

Dizzerin/Rocket-Flight-Data-Computer
This project uses an STM32H743VGT6 MCU along with some innertial measurement units (IMU)s and barometric pressure sensors to and an SD card to record flight data from a model rocket and for later analysis, graphing, and…

DoggeBoi/Servo_PCBs
Collection of proof of consept and "production" PCBs


It measures 64.9 × 33 mm and has 2 copper layers, 1.6 mm thick.
44 parts, built around the LSM6DSO. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the wearpants/jazzhands-hardware repository on GitHub, at the commit this page was made from: the board is main/jazzhands-main.kicad_pcb and its schematic key/jazzhands-key.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask wearpants before reusing the design.