

Pcb lab-1
PCB Lab #1 - Level Shifting
- Size
- 91.4 × 33 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 66
- Nets
- 57
- Pads
- 204
- Tracks, vias
- 600, 95
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 22 Jun 2020
- Updated
- 29 Jun 2020
Overview
Pcb lab-1 is an open-source printed circuit board by vladbelous, from the vladbelous/pcb-lab-1 repository on GitHub. It is a 2-layer board of 91.4 × 33 mm with 66 parts on 57 nets, routed with 600 tracks and 95 vias.
It is built around the ATTINY1614-SSN, 74LVC1G3157 and AP2280-1WG, with the NLSX4373D, TXB0104 and CR2032 among its other parts. Its parts include 18 capacitors, 14 resistors, 10 connectors, 9 ICs and 3 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
6ATTINY1614-SSN
SOIC-14-40℃~+105℃ 1.8V~5.5V 10bit 12 16KB 20MHz 256Byte 2KB 8 Bit 8bit AVR Built-in FLASH SOIC-14 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)74LVC1G3157
UncategorisedDiodes IncorporatedAP2280-1WG
SOT-25-5-40℃~+85℃ 1 1.5V~6V 2A 80mΩ Active High High Side Switch SOT-25-5 Power Distribution Switches ROHSDiodes IncorporatedPower Distribution SwitchesNLSX4373D
SO-8-40℃~+85℃ 1 1.5V~5.5V 1.5V~5.5V 2 20Mbps Automatic direction detection、Output enable high-impedance、Integrated pull-up resistor Bidirectional Level translator SMBus、I2C Tri-State、Open-drain SO-8 Translators, Level Shifters ROHSonsemiTranslators, Level ShiftersTXB0104
UncategorisedTexas InstrumentsCR2032
-- Unclassified goods ROHSMaxellUncategorised
README
README.mdPCB Lab #1 - Level Shifting
"Lab"-style PCB for experimenting with different voltage level shifting solutions, as well as battery voltage measurement and reporting in a multi-voltage system.
TODO: add more description
Schematic:

Parts
66| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100n | Capacitor_SMD:C_0603_1608Metric | C2, C3, C4, C6, C7, C10, C11, C12, C13, C14, C15, C20, C21, C30, C31 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R5, R6, R7, R30, R31, R32, R33 |
| 3 | 1k | local_footprints:0805_HS | R1, R2, R3 |
| 3 | UPDI | local_footprints:Pin_Header_Straight_1x03_Pitch2.54mm | J20, JP20, JP21 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R8, R9 |
| 2 | 1u | Capacitor_SMD:C_0805_2012Metric | C5, C8 |
| 2 | 3.3k | Resistor_SMD:R_0603_1608Metric | R4, R20 |
| 2 | 74LVC1T45-SOT23-6 | local_footprints:SOT-23-6_HS | U11, U12 |
| 2 | JP_RX | local_footprints:Pin_Header_Straight_1x03_Pitch2.54mm | J10, J14 |
| 2 | JP_TX | local_footprints:Pin_Header_Straight_1x03_Pitch2.54mm | J11, J15 |
| 2 | NMOS_GSD | local_footprints:SOT-23_HS | Q30, Q31 |
| 2 | SCL | local_footprints:Pin_Header_Straight_1x03_Pitch2.54mm | JP30, JP32 |
| 2 | SDA | local_footprints:Pin_Header_Straight_1x03_Pitch2.54mm | JP31, JP33 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 74LVC1G3157 | local_footprints:SOT-23-6_HS | U6 |
| 1 | ADC | local_footprints:Pin_Header_Straight_1x03_Pitch2.54mm | JP2 |
| 1 | AP2280 | local_footprints:SOT-23-5_HS | U5 |
| 1 | AP7354 | local_footprints:SOT-23-5_HS | U1 |
| 1 | BAT | local_footprints:Pin_Header_Straight_1x02_Pitch2.54mm | J1 |
| 1 | BTN | local_footprints:SW_SPST_PUSH_6mm_3mm | SW1 |
| 1 | CR2032 | local_footprints:CR2032_Holder_Linx | BT1 |
| 1 | GRN | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | I2C display | local_footprints:Pin_Header_Straight_1x04_Pitch2.54mm | JD1 |
| 1 | JST_PH_BAT | local_footprints:JST_PH_S2B-PH-K_02x2.00mm_Angled_WiderHole | JST_PH_BAT1 |
| 1 | NLSX4373 | local_footprints:SOIC-8_3.9x4.9mm_Pitch1.27mm_HS | U30 |
| 1 | PI4ULS5V201-SOT23-6 | local_footprints:SOT-23-6_HS | U20 |
| 1 | RED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | TXB0104 | local_footprints:SOIC-14_3.9x8.7mm_Pitch1.27mm_HS | U10 |
| 1 | UART | local_footprints:Pin_Header_Straight_1x04_Pitch2.54mm | J18 |
| 1 | UPDI_PIN_SMD | local_footprints:Conn_1-wire | J2 |
| 1 | YEL | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | attiny1614 | local_footprints:SOIC-14_3.9x8.7mm_Pitch1.27mm_HS | U2 |
| 1 | jumper | local_footprints:Pin_Header_Straight_1x02_Pitch2.54mm | JP1 |
Similar boards
- 6 layers69.7 × 22.9 mm

- 2 layers271.8 × 172.7 mm

Peripherl bridge panel
Pongkemon01/Zeabus-Elec-Circuit-Peripheral_bridge
Bridge circuit for several peripheral
1,176 parts - 2 layers103.1 × 86.6 mm

- 2 layers81 × 58.4 mm

- 2 layers

- 2 layers31 × 26.4 mm

- 2 layers45 × 45 mm

- 2 layers84.2 × 86.4 mm

Thesis custom arduino board
lonapse456-glitch/ulang_sys_res
System files of Automated Deep Learning-based Counting System for Giant Freshwater Prawn
41 parts1
Questions
How big is the Pcb lab-1 PCB?
It measures 91.4 × 33 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pcb lab-1 use?
66 parts, built around the ATTINY1614-SSN, 74LVC1G3157, AP2280-1WG and NLSX4373D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pcb lab-1 KiCad files?
From the vladbelous/pcb-lab-1 repository on GitHub, at the commit this page was made from: the board is pcb-lab-1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pcb lab-1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask vladbelous before reusing the design.