
ESP32-Zip Panelized
vintlabs/ESP32-Zip
ESP32 Development Module compatible with Pi Zero cases (hardware)

ESP32 Development Module compatible with Pi Zero cases (hardware)
ESP32-Zip is an open-source printed circuit board by vintlabs, from the vintlabs/ESP32-Zip repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 65 × 30 mm with 47 parts on 63 nets, routed with 728 tracks and 99 vias.
It is built around the CP2102N-A01-GQFN24, ESP32-WROOM-32 and MMBT2222A, with the SP0503BAHTG among its other parts. Its parts include 11 resistors, 10 capacitors, 5 diodes, 4 connectors and 3 ICs. It belongs with the ESP32 boards of this library.
Note: This is not intended to be used with Pi Hats directly, however it is possible that many will work. If you want to try with a Pi Hat, please check the pinouts very carefully!




| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C4, C7, C10 |
| 5 | 10u | Capacitor_SMD:C_0805_2012Metric | C3, C5, C6, C8, C9 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric | R3, R5, R6, R8 |
| 4 | 2.2k | Resistor_SMD:R_0805_2012Metric | R9, R10, R11, R12 |
| 4 | LED | LED_SMD:LED_0805_2012Metric | D2, D3, D4, D5 |
| 2 | MMBT2222A | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | SW_Push | 12V-SmartSwitch:SW_TACTILE_PO21301 | SW1, SW2 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | 22.1k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 47.5k | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | AP7215-33YG-13 | ESP32-Zip:AP7215-33YG-13 | U1 |
| 1 | CP2102N-A01-GQFN24 | ESP32-Zip:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm_CP2102-lessSolder | U2 |
| 1 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | Conn_01x06_Male | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_02x20_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J2 |
| 1 | ESP32-WROOM-32 | 12V-SmartSwitch:ESP32-WROOM-32-Espressif-Symbol-Kicad-62379 | U3 |
| 1 | LOGO | 12V-SmartSwitch:WiFi_logo | G*** |
| 1 | LOGO | ESP32-Zip:halfleaf | G*** |
| 1 | LOGO | 12V-SmartSwitch:BT_logo_sm | G*** |
| 1 | SP0503BAHT | Package_TO_SOT_SMD:SOT-143 | D1 |
| 1 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | JP3 |
| 1 | USB_B_Micro | 12V-SmartSwitch:USB_Micro-B_Amphenol_10118194-0001LF_Horizontal | J1 |
The 41 most common of 47 parts.

vintlabs/ESP32-Zip
ESP32 Development Module compatible with Pi Zero cases (hardware)

vintlabs/ESP32-PWM-Driver-Devkit
ESP WROOM-32 DevKit with 8 2A PWM Drivers (5-15V)



icl-rocketry/VLAD-CanSat
Repository Containing the hardware and firmware of VLAD, a stabby boi who will participate in the Mach-21 CanSat competition

TobleMiner/catear-pcb
This repo contains the PCB for the Nekomimi project of @BenBE . It will be used to illuminate 3D printed catears.

cgbriggs99/InstrumentController
Controller for an instrument panel. Interfaces with MSFS.

neuroidss/FreeEEG32-alpha1.0
ALPHA1.0 TEST FAILED, USE NEW VERSION INSTEAD FreeEEG32 alpha1.0 32 channels mobile electroencephalography under GNU AGPL 24 bits, 4kSPS ADCs 4x AD7770 MCU STM32F427ZI WIFI ESP-12F (ESP8266) USB CP2102N Accel & hyro…

willemcvu/midi-solenoid-driver
A set of PCBs to drive solenoids using MIDI data, for use in automating musical instruments.
It measures 65 × 30 mm and has 4 copper layers, 1.6 mm thick.
47 parts, built around the CP2102N-A01-GQFN24, ESP32-WROOM-32, MMBT2222A and SP0503BAHTG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the vintlabs/ESP32-Zip repository on GitHub, at the commit this page was made from: the board is ESP32-Zip.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).