Skip to the content
4 layers76.6 × 25.1 mmEsp atx power, the printed circuit board in 3D

ESP32 ATX Power Controller

Size
76.6 × 25.1 mm
Copper layers
4
Thickness
1.61 mm
Parts
55
Nets
49
Pads
216
Tracks, vias
413, 303
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
5 Jan 2024
Updated
30 Jan 2026

Overview

Esp atx power is an open-source printed circuit board by valletw, from the valletw/esp-atx-power repository on GitHub, published under the MIT licence. It is a 4-layer board of 76.6 × 25.1 mm with 55 parts on 49 nets, routed with 413 tracks and 303 vias.

It is built around the ESP32-C3-WROOM-02U-N4, TPD1E05U06DPY and AMS1117-3.3, with the TPS2116DRL, USBLC6-2P6 and G3VM-61D1 among its other parts. Its parts include 18 resistors, 11 capacitors, 6 diodes, 6 switches and 4 ICs. It belongs with the home automation and IoT boards and the ESP32 and RISC-V boards of this library.

Main components

9

README

README.md

ESP32 ATX Power Controller

The purpose of this project is to control a computer remotely by connecting directly to the ATX motherboard power IO control. The control will be done with Home Assistant by using ESPHome firmware.

Custom software could be written by using ESP-IDF SDK but it is not the purpose of this project.

Board

Hardware

Double 2.54mm pin headers are set for each ATX functionalities to manage:

  • PWR SW: ATX power button
  • RST SW: ATX reset button
  • PWR LED: ATX power state LED
  • HDD LED: ATX HDD activity LED

Two status LED are available:

  • PWR: 3.3V state
  • STAT: System status controlled by software

Two buttons are available for ESP32 boot sequence:

  • BOOT: Control processor download mode on boot
  • EN: Control processor reset

For advanced debug, the following connectors are available:

  • 2x5 1.27mm pins header JTAG/SWD for external probe
  • 4-pins Molex connector for UART

Board top render Board bottom render

Components choice

This project is based on an ESP32-C3 module to simplify design and ensure good WiFi performance (with external antenna connector). ESP32 has been selected for the big community to generate software and the frameworks available. Espressif hardware design rules has been take into account following there documentation

For easy debug and flashing, ESP32 with USB-CDC and JTAG support has been selected. It allows to remove the USB-UART bridge of the previous design.

The optocouplers for electric isolation have been selected following the PiKVM project experience. In the DIY PiKVM V2 instructions, the OMRON reference is recommended. Others relays/optocouplers may not be sensitive enough or low-level controlled.

The 3.3V to power all the components is generated from an LDO using the 5V of the USB socket. It can also be powered from external 5V on pins header. Both external 5V and USB can be connected at the same time, a power MUX is used to switch between both sources.

All others components has been selected from JLCPCB catalogue to minimize the cost and the assembly fees.

Manufacturing

The board is manufactured by JLCPCB, here is the details you will require to generate an order.

Note: JLCPCB requests some modifications on output files, do not use direct export from KiCad (check the FAQ)

PCB

Files: Gerbers

ConfigurationValue
Base MaterielFR-4
Layers4
Dimensions76.56 x 25.10
Different design1
Delivery formatSingle PCB
PCB thickness1.6
PCB colorGreen (other colors have fees)
SilkscreenWhite
Materiel typeFR4-Standard TG 135-140
Surface finishHASL
Specify layer sequenceF_Cu / In1_Cu / In2_Cu / B_Cu
Impedance controlYes
Layer stackupJLC04161H-7628
Via coveringTented
Min via hole size/diameter0.3mm/0.45mm
Remove order numberSpecify a location

Note: All options have not been detail here, keep default value.

Assembly

Files: BOM, CPL

ConfigurationValue
PCBA typeEconomic
Assembly sideTop
Tooling holesAdded by JLCPCB

Verify "pick & place" orientations and positions on the web viewer

JLCPCB will add 2 tooling holes for assembly (1 mm diameter near the board corners).

Note: All options have not been detail here, keep default value.

ESP32 Pinout

For those who want to reuse this project, here is the ESP32 pinout to manage the different input/output.

NamePinDirection
System Status LEDIO8Output (strapping pin)
ATX Power ButtonIO0Output
ATX Reset ButtonIO1Output
ATX Power StateIO3Input
ATX HDD ActivityIO10Input

ESPHome configuration

Device must be setup via USB connection the first time to flash the customized firmware with sensors/buttons configuration.

Once it has been configured successfully, you should fix the device IP on your router for easier Home Assistant configuration.

Note: Installation can be bypassed if already done or you can use docker image. Check ESPHome documentation for more details.

Installation

shell
pip install esphome
# Ensure your user session has the correct permission for serial port.
sudo usermod -a -G dialout <USERNAME>

Customize

Depending of your installation and network, a secrets.yaml file must be create with your specific configuration.

yaml
# secrets.yaml
hostname: MyControllerHostname
wifi_ssid: MySSID
wifi_password: MyStrongPassphrase
wifi_fb_ssid: ATX Controller Fallback Hotspot
wifi_fb_password: StrongPassphrase
ota_password: MyOTAPassphrase
api_key: 32BytesBase64String

Compile and flash

shell
# Generate the firmware.
esphome compile esphome.yaml
# Flash the firmware to the ESP.
esphome run esphome.yaml
# Get logs.
esphome logs esphome.yaml

Parts

55
QtyValueFootprintReferences
510kResistor_SMD:R_0402_1005MetricR103, R108, R109, R117, R118
4390Resistor_SMD:R_0603_1608MetricR101, R102, R104, R106
4G3VM-61D1Package_DIP:DIP-4_W8.89mm_SMDSocket_LongPadsK101, K102, K103, K104
4~MountingHole:MountingHole_2.7mm_M2.5_ISO7380MH101, MH102, MH103, MH104
3100nCapacitor_SMD:C_0402_1005MetricC101, C105, C106
2100nCapacitor_SMD:C_0603_1608MetricC103, C110
210uCapacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-AC104, C111
222Resistor_SMD:R_0402_1005MetricR112, R113
24.7kResistor_SMD:R_0402_1005MetricR105, R107
25.1kResistor_SMD:R_0402_1005MetricR110, R111
2680Resistor_SMD:R_0402_1005MetricR114, R115
2Ferrite BeadInductor_SMD:L_0603_1608MetricL101, L102
2SMF5.0ADiode_SMD:D_SOD-123FD105, D106
2TPD1E05U06Package_SON:Texas_DPY0002A_0.6x1mm_P0.65mmD101, D102
2TS-1187A-B-A-BButton_Switch_SMD:SW_Push_1P1T_XKB_TS-1187ASW101, SW102
2~Capacitor_SMD:C_0402_1005MetricC108, C109
10Resistor_SMD:R_0402_1005MetricR116
110uCapacitor_SMD:C_0402_1005MetricC102
11uCapacitor_SMD:C_0402_1005MetricC107
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U102
1Conn_01x04Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_HorizontalJ103
1Conn_02x09_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x09_P2.54mm_HorizontalJ102
1Conn_ARM_JTAG_SWD_10Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMDJ101
1ESP32-C3-WROOM-02URF_Module:ESP32-C3-WROOM-02UU101
1GT-USB-7010ASVConnector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASVJ105
1GreenLED_SMD:LED_0805_2012MetricD104
1RedLED_SMD:LED_0805_2012MetricD103
1TPS2116DRLPackage_TO_SOT_SMD:SOT-583-8U104
1USBLC6-2P6Package_TO_SOT_SMD:SOT-666U103

Similar boards

  • 4 layers70 × 70 mmCloudSmoker ver2f, the printed circuit board in 3D

    CloudSmoker ver2f

    cwgstreet/cloudSmoker

    ESP32 wifi enabled quad temperature probe device to monitor bbq meat / pit temperatures with wireless cloud data logging for remote monitoring and push alert notifications

    115 parts24
  • 2 layers76 × 72 mmPanel, the printed circuit board in 3D

    Panel

    NandXor96/USBWLEDC

    USB WLED Controller

    184 parts40
  • 2 layers42 × 98.1 mmPendant, the printed circuit board in 3D

    Pendant

    esplo/cue2keys_resources

    Docs and other resources for Cue2Keys

    69 parts5MIT
  • 2 layers204.3 × 75.1 mmPanelizedESP32, the printed circuit board in 3D

    PanelizedESP32

    valeriyproklov/ESP32-devboard

    An ESP32 devboard I designed in KiCad.

    491 parts2CERN-OHL-P-2.0
  • 2 layers64 × 37 mmBefore silk, the printed circuit board in 3D

    Before silk

    mitra42/frugal-iot-hw-sensor

    A simple, un-opinionated, multi-purpose sensor board, that can be wired to sensors using most common interfaces (I2C, ModBus, OneWire, Analog) with onboard charging and external antenna.

    67 parts
  • 4 layers120 × 79.5 mmNivara PCB, the printed circuit board in 3D

    Nivara PCB

    WenerrP/WENERR_PACHECO_ELECTIVA_2025_C2

    Wenerr Valentín Pacheco Torres.

    182 parts
  • 4 layers82 × 68.9 mmSerialsentinel, the printed circuit board in 3D

    Serialsentinel

    gcormier/serialsentinel

    Find out which serial ports the device has created.

    72 parts3
  • 4 layers68.6 × 56 mmCartridge, the printed circuit board in 3D

    Cartridge

    coco-chameleon/chameleon-hardware

    TRS-80 Color Computer cartridge emulator

    95 partsCERN-OHL-W-2.0

Questions

How big is the Esp atx power PCB?

It measures 76.6 × 25.1 mm and has 4 copper layers, 1.61 mm thick.

What parts does the Esp atx power use?

55 parts, built around the ESP32-C3-WROOM-02U-N4, TPD1E05U06DPY, AMS1117-3.3 and TPS2116DRL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Esp atx power KiCad files?

From the valletw/esp-atx-power repository on GitHub, at the commit this page was made from: the board is kicad/esp-atx-power.kicad_pcb and its schematic kicad/esp-atx-power.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Esp atx power design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).