

Just a badge
- Size
- 85 × 99.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 93
- Nets
- 99
- Pads
- 370
- Tracks, vias
- 1,090, 97
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 22 Nov 2018
- Updated
- 10 May 2021
Overview
Badge is an open-source printed circuit board by urish, from the urish/aramcon-badge repository on GitHub. It is a 2-layer board of 85 × 99.6 mm with 93 parts on 99 nets, routed with 1,090 tracks and 97 vias.
It is built around the E73-2G4M08S1C, GD25Q16CSIG and VS1053B-L, with the AMS1117-1.8, AMS1117-3.3 and PMPB15XP,115 among its other parts. Its parts include 40 capacitors, 14 resistors, 9 diodes, 8 ICs and 5 connectors. It belongs with the lEDs and displays boards and the nRF52 and nRF5x boards of this library.
Main components
9E73-2G4M08S1C
SMD,18x13mm-103dBm、-95dBm -40℃~+85℃ 120m 17.05mA 3.3V 8.27mA 8dBm Bluetooth 5.0、Bluetooth 4.2 PWM、SPI、ADC、USB、I2C、ISP、JTAG、DMA nRF52840 Chip SMD,18x13mm Bluetooth Modules ROHSChengdu Ebyte Elec TechBluetooth ModulesGD25Q16CSIG
SOIC-8-208mil100,000 cycles 120MHz 150ms@(32KB) 16Mbit 2.7V~3.6V 20 Years 5uA 600us SPI SOIC-8-208mil NOR FLASH ROHSGigaDeviceNOR FLASHVS1053B-L
LQFP-48-40℃~+85℃ 1.65V~2V、2.5V~3.6V 8kHz~48kHz Encoder/decoder I2S、SPI、UART LQFP-48(7x7) Audio Interface ICs ROHSVLSI SolutionAudio Interface ICsAMS1117-1.8
SOT-223-40℃~+125℃@(Tj) 0.003%Vout 1 1.3V@(1A) 1.8V 15V 1A 72dB@(120Hz) Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsPMPB15XP,115
DFN2020MD-6-55℃~+150℃ 1 P-Channel 1.7W 100nC@6V 11.8A 12V 19mΩ@4.5V 2.875nF 530pF 900mV DFN2020MD-6 MOSFETs ROHSNexperiaMOSFETsWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedMBR0530
SOD-1231 Independent 30V 5.5A 500mA 550mV@500mA 80uA@30V SOD-123 Schottky Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Schottky DiodesSI1308EDL
SC-70-3-55℃~+150℃ 1 N-channel 1.4nC@10V 1.5A 1.5V 105pF 11pF 132mΩ@10V 23pF 30V 400mW N-Channel SOT-323 MOSFETs ROHSVishay IntertechnologyMOSFETs
README
README.mdThis repository has been been deprecated!
Please use the following repos instead:
Smart Badge Project
nRF52840-Based Smart Badge with Bluetooth, Thread Mesh Network, 2.9" ePaper Display, Neopixels, built-in MP3 Sound decoder and more!
Flashing The Badge
Prerequisites
- Grab a
.uf2file from the releases page, or build a fresh release from our CircuitPython fork.
Instructions
- Move the power switch to "BAT" position, and remove the battery from your badge
- Connect your badge to the PC using a MicroUSB Cable
- Press the left key while switching to "USB" position
- The badge should appear as a drive called
ARAMBOOT - Copy the new
.uf2firmware file to the drive
Directory Structure
CircuitPython Demo Apps
- firmware/nametags - Name tags firmware 📛
- firmware/lib - Common libraries you need for running the other programs
- firmware/clock - Simple clock demo ⌚
- firmware/rock-paper-scissors - Rock-Paper Scisscors game for 2 players 🤘
- firmware/clicker - Simple USB HID Clicker with Applause function
- firmware/touch-piano - Capacitive Touch piano (requires MPR121 breakout board) 🎹
- firmware/magicblue-bulb - Control a Bluetooth light bulb (Magic Blue) 💡
Other stuff
- pcb/badge - Badge PCB, designed with KiCad
- pcb/svg2mod - svg2mod with some patches
Hardware Information
- nRF52840 64MHz ARM Cortex-M4F64 CPU with 1MB flash, 256KB ram, USB, Bluetooth Low Energy 5, Thread, and Zigbee
- GDEW029T5 2.9 inch e-paper glass display
- VS1003 MP3/WMA Audio Codec
- LIS2DH12 I2C Accelerometer
- GD25Q16C 16MBit Serial Flash
- 4 WS2812B "NeoPixel" Addressable RGB LEDs
- 3 CHERRY MX Keyboard Switches
- Shitty Add-On (SAO) Connector
- Vibration motor
- Red LED
Pinout
| Pin | Component | Function |
|---|---|---|
| P0.00 | VS1003 MP3 Codec | RESET |
| P0.01 | E-Paper, MP3 Codec | SCLK |
| P0.02 | Keyboard Switch | Left |
| P0.03 | Accelerometer, SAO | SDA |
| P0.06 | E-Paper | RESET |
| P0.07 | E-Paper | CS |
| P0.08 | WS2812 Neopixels | DATA |
| P0.12 | E-Paper | D/C |
| P0.13 | VS1003 MP3 Codec | DREQ |
| P0.17 | Vibrator | Vibrate |
| P0.20 | Serial Flash | SO/IO1 |
| P0.22 | Serial Flash | SI/IO0 |
| P0.24 | VS1003 MP3 Codec | xDCS |
| P0.26 | E-Paper | BUSY |
| P0.28 | Accelerometer, SAO | SCL |
| P0.29 | Keyboard Switch | Middle |
| P0.30 | Battery Voltage | Analog |
| P0.31 | Keyboard Switch | Right |
| P1.00 | Serial Flash | SCK |
| P1.02 | Serial Flash | CS |
| P1.04 | Serial Flash | WP/IO2 |
| P1.06 | Serial Flash | HOLD/IO3 |
| P1.09 | E-Paper, MP3 Codec | MISO |
| P1.10 | E-Paper, MP3 Codec | MOSI |
| P1.11 | Red LED | Cathode |
| P1.13 | VS1003 MP3 Codec | CS |
Parts
93| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 100nF | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5, C6, C7, C10, C13, C14, C15, C17, C18, C19, C25, C26, C37, C39 +2 |
| 11 | 1uF | Capacitor_SMD:C_0603_1608Metric | C23, C27, C28, C29, C30, C31, C32, C33, C34, C35, C36 |
| 4 | 100k | Resistor_SMD:R_0603_1608Metric | R5, R6, R8, R9 |
| 4 | 10uF | Capacitor_SMD:C_0603_1608Metric | C11, C16, C38, C40 |
| 4 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D6, D7, D8, D9 |
| 3 | 20R | Resistor_SMD:R_0603_1608Metric | R2, R3, R4 |
| 3 | MBR0530 | Diode_SMD:D_SOD-123 | D1, D2, D3 |
| 3 | SW_Push | Button_Switch_Keyboard:SW_Cherry_MX1A_1.00u_PCB | SW1, SW2, SW3 |
| 2 | 10nF | Capacitor_SMD:C_0603_1608Metric | C20, C21 |
| 2 | 33pF | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 470R | Resistor_SMD:R_0603_1608Metric | R12, R13 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D4, D5 |
| 2 | Si1308EDL | Package_TO_SOT_SMD:SOT-323_SC-70 | Q1, Q2 |
| 1 | logo:aramcon-logo | svg2mod | |
| 1 | 0 | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | R7 |
| 1 | 0.47R | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 100uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C12 |
| 1 | 10K | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 12.288M | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 390R | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C24 |
| 1 | 4.7uH | Inductor_SMD:L_1210_3225Metric | L2 |
| 1 | 47nF | Capacitor_SMD:C_0603_1608Metric | C22 |
| 1 | 68uH | Inductor_SMD:L_1210_3225Metric | L1 |
| 1 | AMS1117-1.8 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | AudioJack4 | connectors:Jack_3.5mm_PJ320D_Horizontal | J1 |
| 1 | Battery_Cell | AA_battery_clip:BK-53_MPD_AAClip | BT1 |
| 1 | Buzzer | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | BZ1 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J6 |
| 1 | E73-2G4M08S1C | EBYTE:E73-2G4M08S1C | U3 |
| 1 | G*** | logo:board-shape | SHAPE |
| 1 | GD25Q16C | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | LIS2DH12TR | Package_LGA:LGA-12_2x2mm_P0.5mm | U7 |
| 1 | PFC24/0.5mm | connectors:EPD-FPC-1x24-P0.50mm_Horizontal | J7 |
| 1 | PMPB15XP,115 | PMPB15XP_115:MOSFET_PMPB55ENEAX | U6 |
| 1 | SAO_CONN | Connector_PinSocket_2.54mm:PinSocket_2x02_P2.54mm_Vertical | J2 |
| 1 | SW_SPDT | Button_Switch_THT:SW_CuK_OS102011MA1QN1_SPDT_Angled | SW4 |
| 1 | TPS610986DSET | SON50P150X150X80-6N:SON50P150X150X80-6N | U4 |
| 1 | TP_3V3 | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | TP_GND | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | TP_SWCLK | TestPoint:TestPoint_Pad_D1.5mm | TP3 |
| 1 | TP_SWDIO | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J4 |
| 1 | VS1053B | Package_QFP:LQFP-48_7x7mm_P0.5mm | IC1 |
More from urish/aramcon-badge
1- 2 layers137.9 × 57.6 mm

Similar boards
- 2 layers

HabitReminderEPaper
Rikeroo/habit-reminder
Low energy physical habit reminder, using RGB LEDs, a small task screen and tactile switches to build useful habits and get tasks done
52 parts - 4 layers83.4 × 42.1 mm

H C3-ulp29
martinberlin/H-C3-029-eink
This is a joint project between Larry Bank and Fasani Corp with the purpouse to make an easy and unexpensive nRF52 BLE badge with a SPI 2.9", a QWIIC connector, and on board RTC
54 parts5MIT - 2 layers80 × 50 mm

Lcd dual
Novin3dp/7inch-hdmi-screen
این برد دولایه (۶۸×۴۲ میلیمتر) همان پنل ۷ اینچ AT070TN92 و تاچ GT915 را این بار از پورت DSI رزبریپای راه میاندازد. نسخهی HDMI در پوشهی hardware/ دستنخورده باقی مانده است.
127 parts1 - 2 layers25.9 × 44.2 mm

M5StampC3
Uspizig/M5StampC3-EINK
Eink Board Addon for M5Stack Stamp C3 for Eink Waveshare Displays
38 parts4 - 4 layers74.1 × 130 mm

- 2 layers65 × 70 mm

- 2 layers44.5 × 31.7 mm

- 2 layers45 × 45 mm

Aeroq Hardware v3
EnriqueNeyra/Aeroq
An Indoor Air Quality Monitor Powered by ESP32, SCD40, and SEN54
56 parts130
Questions
How big is the Badge PCB?
It measures 85 × 99.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Badge use?
93 parts, built around the E73-2G4M08S1C, GD25Q16CSIG, VS1053B-L and AMS1117-1.8. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Badge KiCad files?
From the urish/aramcon-badge repository on GitHub, at the commit this page was made from: the board is pcb/badge/badge.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Badge design in my own project?
Its repository states no licence, so its author keeps all rights: ask urish before reusing the design.