Skip to the content
2 layers81.1 × 128.5 mmMultimult, the printed circuit board in 3D

Mostly Eurorack projects

Size
81.1 × 128.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
113
Nets
59
Pads
290
Tracks, vias
445, 18
Pours
3
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
16 Jan 2021
Updated
19 Sep 2026

Overview

Multimult is an open-source printed circuit board by tpcarlson, from the tpcarlson/synth-diy repository on GitHub. It is a 2-layer board of 81.1 × 128.5 mm with 113 parts on 59 nets, routed with 445 tracks and 18 vias.

Its parts include 29 connectors, 24 resistors, 14 capacitors, 8 diodes and 6 ICs. It belongs with the audio and music boards of this library.

README

vcadsr/README.md

VCADSR

What is this?

Voltage controlled ADSR, using the ElectricDruid EnvGen8 chip. The module provides voltage control over most parameters (Attack, decay, sustain, release, time, level) as well as manual control with sliders. There are also three switches for toggling the mode, linear/exponential, and a fifth stage called "punch" which adds a little bit more to the attack on an envelope.

The mode toggle switch allows for gated looping, just looping (Almost like an LFO), and normal ADSR mode.

How much power does it use?

As measured by the joranalogue Test 3, around 40mA on +12v and 30mA on -12v at peak. The 5v rail is unused.

Where does the design come from?

The schematic is really an extension of the reference design on the ElectricDruid site, with some changes to add LEDs, and cutting features that would otherwise take up more panel space than I was comfortable with - I dropped the attenuators for CV inputs in favour of nice big manual controls with linear potentiometers instead.

Are there any rare/weird parts used?

You'll need one of the EnvGen8 chips in order to make this function at all!

Are there any problems with the design?

Just a couple, which are corrected in the version here. First, the LEDs for gate and trigger had some issues drawing too much power due to an oversight in the schematic. As it turns out LEDs don't really like being driven without a resistor! Second, the panel design had the mode and linear/exponential graphics switched which makes operating it a little bit more confusing than it otherwise ought to be.

These problems are both fixed in the repository right now though, however the fixes are untested. If I make another run of these boards, I will verify that the fix worked and remove this whole section!

Do you have a BOM/Mouser cart/Tayda links?

Sorry, no. Things go out of stock so frequently it'd be a lot of work to keep these up to date. Everything in this project is easy to source though, so you should not have any trouble.

Other resources
  • Assembly instructions
  • Interactive BOM - This includes pre-soldered SMT parts as well as the through-hole parts. To use this, save the 'raw' view to your computer and open it in a web browser

Parts

113
QtyValueFootprintReferences
24AudioJack2Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHolesJ1, J2, J10, J11, J12, J13, J14, J15, J16, J17, J18, J19, J20, J21, J22, J23 +8
18100RResistor_SMD:R_0805_2012MetricR1, R2, R4, R5, R6, R10, R12, R13, R15, R16, R17, R18, R20, R21, R23, R24 +2
12100nCapacitor_SMD:C_0805_2012MetricC3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C13, C14
61kResistor_SMD:R_0805_2012MetricR3, R7, R11, R14, R19, R22
6LED_Dual_2pinLED_THT:LED_D3.0mmD1, D4, D5, D6, D7, D8
6TL074Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU1, U2, U3, U4, U5, U6
210uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1, C2
2D_SchottkyDiode_THT:D_A-405_P7.62mm_HorizontalD2, D3
2OSHWSymbol:OSHW-Logo_5.7x6mm_SilkScreenJ27, J29
2WEEESymbol:WEEE-Logo_4.2x6mm_SilkScreenJ26, J28
1Conn_02x05_Odd_EvenConnector_IDC:IDC-Header_2x05_P2.54mm_VerticalJ5

The 81 most common of 113 parts.

More from tpcarlson/synth-diy

12
  • 4 layers241.2 × 327.2 mmCyclic, the printed circuit board in 3D

    Cyclic

    tpcarlson/synth-diy

    Mostly Eurorack projects

    439 parts107
  • 2 layers293.3 × 128.5 mmTwoshot, the printed circuit board in 3D

    Twoshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    223 parts107
  • 4 layers179.5 × 128.5 mmSynth diy, the printed circuit board in 3D

    Synth diy

    tpcarlson/synth-diy

    Mostly Eurorack projects

    175 parts107
  • 4 layers313.1 × 185.6 mmOneshot, the printed circuit board in 3D

    Oneshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    172 parts107
  • 2 layers85.4 × 128.5 mmKinky lynx, the printed circuit board in 3D

    Kinky lynx

    tpcarlson/synth-diy

    Mostly Eurorack projects

    165 parts107
  • 2 layers286.9 × 128.7 mmLattice, the printed circuit board in 3D

    Lattice

    tpcarlson/synth-diy

    Mostly Eurorack projects

    161 parts107
  • 2 layers40.3 × 109.6 mmImpact main, the printed circuit board in 3D

    Impact main

    tpcarlson/synth-diy

    Mostly Eurorack projects

    159 parts107
  • 2 layers191.3 × 128.5 mmSycamore, the printed circuit board in 3D

    Sycamore

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 4 layers179.1 × 128.5 mmVcadsr, the printed circuit board in 3D

    Vcadsr

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 2 layers94.3 × 128.5 mmLeaky bucket, the printed circuit board in 3D

    Leaky bucket

    tpcarlson/synth-diy

    Mostly Eurorack projects

    137 parts107
  • 2 layers101.3 × 128.5 mm3-phase lfo, the printed circuit board in 3D

    3-phase lfo

    tpcarlson/synth-diy

    Mostly Eurorack projects

    129 parts107
  • 2 layers131.8 × 57.6 mmRowan, the printed circuit board in 3D

    Rowan

    tpcarlson/synth-diy

    Mostly Eurorack projects

    115 parts107

Similar boards

  • 2 layers122.5 × 87.6 mmControllerCircuit, the printed circuit board in 3D

    ControllerCircuit

    stuartpittaway/diyBMSv4

    Version 4 of the diyBMS

    113 parts1.1k
  • 2 layers243.2 × 106 mm3W6, the printed circuit board in 3D

    3W6

    weteor/3W6

    a small compact 3x5+3 split ortho keyboard

    113 parts488
  • 2 layers294 × 100 mmChu main, the printed circuit board in 3D

    Chu main

    whowechina/chu_pico

    Pico controller for Chunithm-type rhythm game

    113 parts196
  • 2 layers247.1 × 121.4 mmChoctopus44, the printed circuit board in 3D

    Choctopus44

    SlightHeadache/choctopus44

    Choctopus44 is a custom low profile keyboard

    113 parts99
  • 2 layers120 × 80 mmRx72t 100 pga usb, the printed circuit board in 3D

    Rx72t 100 pga usb

    hirakuni45/RX

    Renesas RX Microcontroller, C++ framework, Library, Sample

    113 parts86BSD-3-Clause
  • 2 layers55 × 100 mmESP32AY, the printed circuit board in 3D

    ESP32AY

    djspawnbrest/ESP32AY

    ZxPod - ESP32 based AY multiformat player

    113 parts59GPL-3.0
  • 2 layers191 × 118.7 mmAJ Mid R, the printed circuit board in 3D

    AJ Mid R

    Salicylic-acid3/PCB_Data

    113 parts51MIT

Questions

How big is the Multimult PCB?

It measures 81.1 × 128.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Multimult use?

113 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Multimult KiCad files?

From the tpcarlson/synth-diy repository on GitHub, at the commit this page was made from: the board is multimult/multimult.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Multimult design in my own project?

Its repository states no licence, so its author keeps all rights: ask tpcarlson before reusing the design.