2 layers97 × 91.3 mm
Mh custom v1.3
crice009/toolauth-hardware
The custom PCB for the toolauth system. Intended to control access to tools (based on credentials) in a shared workshop. Designed to work with an ESP32 board and ESPHome.
123 parts1
2 layers91.3 × 91.3 mm
Wing combo
Toolauth/wing-combo1A large Feather Wing board that can control tools and helps manage authorization in a community workshop
- Size
- 91.3 × 91.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 135
- Nets
- 115
- Pads
- 458
- Tracks, vias
- 1,313, 112
- Pours
- 37
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 7 Mar 2024
- Updated
- 11 Apr 2026
Overview
Wing combo is an open-source printed circuit board by Toolauth, from the Toolauth/wing-combo repository on GitHub. It is a 2-layer board of 91.3 × 91.3 mm with 135 parts on 115 nets, routed with 1,313 tracks and 112 vias.
It is built around the CFM06S050-T, 74HC02 and AMS1117-3.3, with the LM393, AO3400A and JQC-3FF/005-1ZS(551) among its other parts. Its parts include 40 resistors, 24 capacitors, 24 connectors, 4 ICs and 3 diodes.
Main components
8CFM06S050-T
-AC-DC Power ModulesCincon Electronics Co. LTD74HC02
-- Logic Gates ROHSonsemiLogic Gates
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
LM393
SOP-8-16V~16V 0℃~+70℃ 2 2.5mA 250nA 2V~36V 36V 5mV 5nA Fail-safe function Open-drain SOP-8 Comparators ROHSMSKSEMIComparators
AO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
JQC-3FF/005-1ZS(551)
插件,19x15.5mm-40℃~+85℃ 100mΩ 10A 10A@277VAC、10A@28VDC 10ms 30V@DC、277V@AC 360mW 5 5V 5ms 70Ω AgCdO Non-Polarized - Single Coil One set changeover: 1C (SPDT - changeover) 插件,19x15.5mm Power Relays ROHSHFPower Relays
SS14
SMA(DO-214AC)-55℃~+150℃ 1A 25A 300uA@40V 40V 550mV@1A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
PY14-02
-- Relay Sockets and Accessories ROHSOmronUncategorised
README
README.mdCombined Use Board
This is the flagship board for the Toolauth project. More information about use, setup, and firmware is available in this repo's wiki.
It can allow for the management of power tools, and serve as the gateway for user authorization in a shared workshop.
The board has the following features:
- A stack of relays & a contactor for controlling power to the downstream tool.
- Its own power supply, to draw from the line supplying the downstream tool (no extra power needed, if under 220VAC).
- An ADE7953 current sensor, to monitor energy use/ status of the connected tool.
- Connectors to add in an RFID card reader (workshop member's badges can swipe).
- Connections for a hardware bypass, for quick-enabling of the tool.
- Simple connection for panel-mounted Red & Green status LEDs.
- 5V supply (from onboard transformer) in USB and solder-able form, for future expansion.
How do I play with this PCB design?
It is as easy as downloading this design by whatever means you like: zip file, clone, etc. Then, open the wing-combo.kicad_pro file with any version of KiCAD you like, but the newest version will probably be best.
Adafuit Feather Specification
In avoidance of obsolescence, we have designed this board to the Adafruit's Feather Specification. The logic here is that the Feather specification itself should allow us to upgrade the 'brain' of this wing without needing a major re-design.
Yes, we could have designed a specific ESP32 into the board. But experience with previous generations has taught us that it is more convenient to make the boards with a MAC address removable.
IOT Hosting
This project was designed to work with Home Assistant and ESPHome, because they allow us to host the whole solution on-premises. However, this board is not tied to that stack by any means. There are lots of ways firmware and software could come together to make this work.
Design Software
Parts
135| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R3, R4, R22, R23, R24, R25, R28, R30, R31, R36, R37, R38, R39, R40 |
| 13 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R5, R6, R14, R15, R16, R17, R18, R20, R21, R26, R27, R29 |
| 11 | no-filter-1 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2, JP3, JP4, JP5, JP6, JP7, JP8, JP9, JP15, JP16 |
| 10 | 33nF | LED_SMD:LED_0603_1608Metric | C3, C4, C5, C6, C7, C8, C9, C10, C11, C12 |
| 6 | AO3400A | Package_TO_SOT_SMD:SOT-23 | T1, T2, T3, T4, T5, T6 |
| 5 | bridged | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP10, JP11, JP12, JP18, JP19 |
| 4 | 100 | Resistor_SMD:R_0603_1608Metric | R9, R10, R11, R12 |
| 4 | 100nF | LED_SMD:LED_0603_1608Metric | C13, C16, C17, C22 |
| 4 | Conn_01x03_Female | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J13, J14, J15, J17 |
| 3 | Connector_Audio:Jack_3.5mm_CUI_SJ1-3525N_Horizontal | J5, J6, J7 | |
| 3 | 4.7uF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C18, C19, C23 |
| 3 | Screw_Terminal_01x06 | screw_terminal:CONN-TH_6P-P5.00_MX128-5.0-06P-GN01-CU-Y-A | J20, J21, J22 |
| 2 | 0.1uF | LED_SMD:LED_0603_1608Metric | C1, C2 |
| 2 | 2.2k | Resistor_SMD:R_0603_1608Metric | R7, R8 |
| 2 | 20pF | LED_SMD:LED_0603_1608Metric | C20, C21 |
| 2 | 499k | Resistor_SMD:R_0603_1608Metric | R13, R19 |
| 2 | 56k | Resistor_SMD:R_0603_1608Metric | R34, R35 |
| 2 | Conn_01x02_Female | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J18, J19 |
| 2 | Conn_01x04_Female | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J11, J12 |
| 2 | Conn_01x12 | Connector_PinSocket_2.54mm:PinSocket_1x12_P2.54mm_Vertical | J1, J3 |
| 2 | Conn_01x16 | Connector_PinSocket_2.54mm:PinSocket_1x16_P2.54mm_Vertical | J2, J4 |
| 2 | Fuse | Fuse:Fuseholder_Cylinder-5x20mm_Stelvio-Kontek_PTF78_Horizontal_Open | F1, F2 |
| 2 | JQC-3FF/005-1ZS(551) | Relay_THT:Relay_SPDT_SANYOU_SRD_Series_Form_C | relay1, relay2 |
| 2 | R_US | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R32, R33 |
| 2 | SS14 | Diode_SMD:D_SMA | D2, D3 |
| 2 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP13, JP14 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C24 |
| 1 | 10uF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C14 |
| 1 | 1uF | LED_SMD:LED_0603_1608Metric | C15 |
| 1 | 3.58MHz | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | 74HC02 | 74hc02d:SOIC-14_L8.7-W3.9-P1.27-LS6.0-BL | U1 |
| 1 | ADE7953xCP | Package_CSP:LFCSP-28-1EP_5x5mm_P0.5mm_EP3.14x3.14mm | U2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Buzzer | buzzer:BUZ-TH_BD12.0-P7.60-D0.6-FD | BZ1 |
| 1 | CFM06S050 | CFM06S050-E - Cincon:CFM06S050E | PS1 |
| 1 | Conn_01x02_Female | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | Conn_01x02_Female | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J10 |
| 1 | Conn_01x06_Female | Connector_JST:JST_PH_B6B-PH-K_1x06_P2.00mm_Vertical | J16 |
| 1 | H/L1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J23 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LM393 | lm393:SOIC-8_L5.0-W4.0-P1.27-LS6.0-BL | U4 |
| 1 | PMOS | Package_TO_SOT_SMD:TSOT-23 | Q1 |
| 1 | PY14-02 | Library:Relay_Socket_4PDT_Omron_PY14-02-local | relay3 |
| 1 | Polyfuse | Fuse:Fuse_1812_4532Metric | F3 |
| 1 | USB_C_Receptacle_USB2.0_16P | usbc:USB-C-TH_GT-USB-7055 | J8 |
| 1 | powered | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J24 |
The 129 most common of 135 parts.
Questions
How big is the Wing combo PCB?
It measures 91.3 × 91.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wing combo use?
135 parts, built around the CFM06S050-T, 74HC02, AMS1117-3.3 and LM393. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wing combo KiCad files?
From the Toolauth/wing-combo repository on GitHub, at the commit this page was made from: the board is wing-combo.kicad_pcb and its schematic ade7953.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wing combo design in my own project?
Its repository states no licence, so its author keeps all rights: ask Toolauth before reusing the design.
Similar boards
- 2 layers100 × 70 mm
Sensor node
epim/circsim
Post-routed PCB+Schematic circuit simulator. Because I have trust issues.
94 partsMIT - 2 layers37 × 70.9 mm
Opendiag
maximus64/opendiag-hardware
OpenDIAG - Open Source OBD2 Interface (Hardware)
148 parts5CERN-OHL-S-2.0 - 4 layers59.6 × 48.3 mm
Plant1337
chl33/Plant133
Firmware, circuit design, and 3D-printable components for an automated plant-watering system.
61 parts6MIT - 4 layers68.6 × 53.3 mm
- 4 layers100 × 100 mm
AFE
Blaze-Pascal/Masters-Multi-Channel_DAQ
Custom 2-channel digital oscilloscope DAQ with 20MHz bandwidth. Built with a custom KiCad analog front-end (AFE) PCB, Gowin FPGA (Tang Nano 9K) for high-speed signal buffering (VHDL), and an RPi Pico MCU for SCPI-like…
216 parts2GPL-3.0 - 2 layers34.8 × 65.9 mm
- 4 layers279.5 × 97 mm
Alpha centauri pcb
jacob-w-gable/alpha_centauri
A split, ergonomic, mechanical keyboard with 40 keys, designed for typing speed and comfort.
224 parts1MIT