Skip to the content
2 layers88 × 102 mmToniebox v1v2, the printed circuit board in 3D

KiCad schematic of the Toniebox PCB (including datasheets).

Size
88 × 102 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
132
Pads
154
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 7 (file 20221018)
Created
10 Feb 2020
Updated
7 May 2024

Overview

Toniebox v1v2 is an open-source printed circuit board by toniebox-reverse-engineering, from the toniebox-reverse-engineering/toniebox-pcb repository on GitHub. It is a 2-layer board of 88 × 102 mm with 11 parts on 132 nets.

It is built around the CC3200R1M2RGCR, AP2112K-3.3 and MMA8451QT, with the FDV301N among its other parts.

Main components

4

README

README.md

Toniebox PCB

Repository which will lead to a complete schematic of a Toniebox PCB. The schematic is done with KiCad.

View this project on CADLAB.io.

Source of CC3200 footprint: https://raw.githubusercontent.com/Turegano/CC3200/master/lib/CC3200.lib

Table Of Contents

Folders

Status

Top

Bottom

  • red dot: fully documented
  • blue dot: partially documented

Remaining Work

  • create subsheets for logical blocks

  • create pinout of ASICs

  • document remaining testpoints

    T1: NSS40200LTG

Block Diagrams

Block diagram with testpoints

BQ24400 (charge IC) with testpoints

Testpoints

TPConnected toComment
TP1U1 MCLKexternal master clock
TP2U1 GPIO1/ U2 pin 55 GPIO1
TP3K2 pin 9SD detect
TP4U2 pin 29ANT SEL1 Antenna Selection Control
TP5U2 pin 30ANT SEL2 Antenna Selection Control
TP6BQ24400 GND/Battery GNDBattery GND is connected with PCB GND via R55 (0R05)
TP7U2 pin 11/U3 pin 6/R27(?)SCK
TP8U2 pin 12/U3 pin 5/R26(?)SI
TP9U2 pin 13/U3 pin 2/R25(?)SO
TP10U2 pin 14/U3 pin 8/R28(?)VCC
TP11U7 pin 3 (~LED)Charge status LED, connected to U6 output via 100k pull up and U2 pin 20 via 1k2
TP12U5 ASK/OOKcan be configured as an output to provide the received analog signal output
TP14audio jack
TP15audio jack
TP16U1 VOL/MICDETECT
TP17K9 pin 3/U1speaker+
TP18K9 pin 2/U1speaker-
TP19U1 pin 31/D12/U2 pin 62 GPIO7/U5 ENDAC reset
TP20U5 VDD_X
TP21U5 VDD
TP22U5 BG
TP23U5 VINVoltage of U320, if faulty check TP321
TP24U5 VDD_A
TP25U4 pin 3Accelerometer DNC
TP26K4 pin 1/U2 pin 57/R60 (1k)(?)/R394 (1k2)(?)/ears, fed from regulator U6/TP52
TP27D10 pin 1LED red -
TP28D10 pin 2LED green -
TP29D10 pin 3LED blue -
TP30U5 IO 5
TP31K4 pin 3/U2 pin 59/R64(1k)(?)ears, fed from regulator U6/TP52
TP32
TP33U5 MOD
TP34U5 SYS
TP35U5 ENWhen high NFC IC is enabled. If faulty check TP19. Fed by U8 via D13 (is connected to U2 GPIO7).
TP36U5 EN2
TP37NFC socket
TP38K8 pin 3/T1/D12 (battery control circuit)/T340/T342bat+
TP39U320 VIN, T320 collector voltage for U320 EN via R320; U6 VIN; U8 VINfeeds U320, U6, U8 with VCC; enables U320 via T320
TP41Circuit next to U100V w/o battery, ~ bat. Voltage w/ battery; output of T344; connected to U10; controls T343, T342, T340
TP42BQ24400 BAT input
TP43U10 /battery voltage after R89; w/ battery: voltage < bat voltage; w/ power supply 3.8 – 4.4V; check TP38 if not ok
TP45K8 pin 1/U7 pin 5 (TS)temp sense; connected via R47 with BQ24400 and battery NTC.
TP46BQ24400 TIMER PROGRAM
TP47U2 pin 8/output L300 via 1:1 voltage divider R75/R72Supervising U300+circuitry; measured between D301 and L300; 50% voltage via divider R75/R72 to U2 pin 8
TP48U2 pin 61/U8 ENABLE via R56 (10k pulldown)U2 enables LDO U8 with GPIO6. If U8 is not working (TP50) check U8 at TP39
TP49U2 pin 60
TP50U8 VOUT/U9 VIN/U1 IOVDD/U1 HPVDD/SPKVDD/AVDD3V3 output of LDO U8, 1V8 input of LDO U9, T11, U4. 3V3 input U1; if not ok check TP48.
TP51U9 VOUT/U1 DVDP1V8 output of LDO U9. Feeds U1 at PIN 3; if not ok check ENABLE at TP50 and input voltage at TP39.
TP52U6 VOUT 3V3/ U2 VIN IO1, VIN IO2, VIN DCDC ANA, VIN DCDC PA, VIN DCDC DIG, VD2 ANA2/ VCC for U3,T7, T360, T320, SV BQ24400 LED/ RGB LED3V3 output LDO U6: feeds U2, U3, T360 (TP360), TP320, LED output of BQ24400 (TP11)
TP53audio jack
TP54VCCPower supply voltage; if power supply is ok check L8 (SMT Common Mode Line Filter 2x500mH) and D4 (15V TVS Diode)
TP55GND power jack
TP65audio jack
TP66U2 pin 43/pin 9/pin 56U2 internal voltage
TP67U2 pin 38/pin 36/pin 48/pin 25U2 internal voltage
TP68U2 pin 48U2 internal voltage
TP69U2 pin 24U2 internal voltage
TP70T9middle pin (SMD 13014)
TP71U5 VSS PA/VSS RF/VSS/VSS D/NFC connector outer contacts
TP72U1 AIN1
TP73U1 AIN2
TP74U5 IRQ
TP75U300 VINcomes from R305 (0R). U300 generates voltage when operating with power supply; if not ok check TP301
TP300U300 ISENS/T347 via R344U300 output voltage; main supply when connected to power supply; input voltage of voltage divider R344/R345 for U10.
TP301D6Main voltage after D6;if not ok check TP54
TP320U320 ENABLE/T320ENABLE U320 from T320; T320 is supplied via R320 (470k) from D301 (TP39); T320 is controlled by U2 pin 58; if not ok check TP361 and supply voltage of TP39
TP321U320 output/U5 inputU320 supplies U5; if not ok check TP320 and TP39 for supply voltage; if supply voltage check TP322
TP322U320 feedbackVoltage for regulating output voltage of U320; output voltage of divider R321 (470k)/R322 (180k); should be 1.31V-1.51V; divider is fed by U320 output; if not ok check output TP321, input TP39, ENABLE TP320
TP341U10 circuitry;output of T347; controls T346, T345, T341; LOW when operating with power supply; ~ bat voltage when operating with battery; check TP342 and TP38
TP342U10 circuitry/voltage divider R344/R345Voltage divider R344/R345; fed from output of U300; triggers T344, T347 getriggert; operating with power supply: 1V; battery mode: 0V;check TP300
TP350U2 pin 3I2C_SCL
TP351U2 pin 4I2C_SDA
TP355config(?) R connected to GND
TP356config(?) R connected to GND
TP357config(?) R connected to GND
TP358config(?) R connected to GND
TP360K2 pin4SD VDD;T360 switches 3V3 of U6; T360 is controlled by U2 GPIO3 PIN58; check TP361
TP361T320/T360 (voltage)T320 switches ENABLE of U320 / T360 controls voltage SD card
TP370U2 pin 34 SOP1
TP371U2 pin 35 SOP0
TP372U2 pin 17 TDO
TP373U2 pin 18

Parts

11
QtyValueFootprintReferences
5FDV301Ndigikey-footprints:SOT-23-3T4, T5, T6, T7, T11
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U8
1AP2120N-1.8Package_TO_SOT_SMD:SOT-23U9
1CC3200R1M2RGCRdigikey-footprints:VFQFN-64-1EP_9x9mmU2
1IS25LQ032B-JNLEPackage_SO:TSSOP-8_4.4x3mm_P0.65mmU3
1MMA8451QTdigikey-footprints:VQFN-16_3x3mmU4
1TLV320DAC3100Package_DFN_QFN:Texas_S-PVQFN-N32_EP3.45x3.45mmU1

Similar boards

  • 2 layers102.4 × 77.4 mmScheda PSE, the printed circuit board in 3D

    Scheda PSE

    Eduzyolo/PSE_project

    This is the official repo for the PSE project

    176 parts1
  • 2 layers86.4 × 81.9 mmOpen ruche monitoring, the printed circuit board in 3D

    Open ruche monitoring

    fcl2002/Open-Ruche-Monitoring

    An intelligent beehive monitoring solution combining embedded AI, LoRaWAN communication, and solar power to help beekeepers protect their colonies and optimize hive management.

    28 parts1MIT
  • 4 layers41.2 × 49.5 mmPcb, the printed circuit board in 3D

    Pcb

    louislwh/pcb

    44 parts
  • 2 layers68.6 × 53.3 mmMicroP Final Porject, the printed circuit board in 3D

    MicroP Final Porject

    Sebastian-S-Posada/balloon-data-logger-shield

    An Arduino Uno shield, designed in KiCad, that logs temperature, humidity, barometric pressure, and acceleration to a microSD card. It's built as a lightweight, low-power payload for a high-altitude balloon flight.

    21 parts
  • 2 layers18 × 20.1 mmMMA845X, the printed circuit board in 3D

    MMA845X

    vul-os/sirboard

    Open hardware: 107 KiCad PCB designs — SMD-to-THT breakout adapters, ATTiny/ATMega/ESP development boards, and a 39-part sensor line on a common JST-SH connector.

    20 parts56Apache-2.0
  • 2 layers65 × 22.6 mmPhoenix, the printed circuit board in 3D

    Phoenix

    wFairmanOlin/OlinRocketryClub

    Repo for a self-designed flight computer

    35 parts6
  • 2 layers82.6 × 100 mmKm ultimate badge kit, the printed circuit board in 3D

    Km ultimate badge kit

    KnoxMakers/Electronics

    schematics, board files, firmware, slide decks, and the like

    34 parts3

Questions

How big is the Toniebox v1v2 PCB?

It measures 88 × 102 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Toniebox v1v2 use?

11 parts, built around the CC3200R1M2RGCR, AP2112K-3.3, MMA8451QT and FDV301N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Toniebox v1v2 KiCad files?

From the toniebox-reverse-engineering/toniebox-pcb repository on GitHub, at the commit this page was made from: the board is v1-v2/hardware/toniebox-v1v2.kicad_pcb and its schematic v1-v2/hardware/toniebox-v1v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Toniebox v1v2 design in my own project?

Its repository states no licence, so its author keeps all rights: ask toniebox-reverse-engineering before reusing the design.