Skip to the content
4 layers110 × 80 mmSpin rig controller, the printed circuit board in 3D

Model rocket flight computer, ground station, iOS app, and simulation

Size
110 × 80 mm
Copper layers
4
Thickness
1.6 mm
Parts
170
Nets
126
Pads
520
Tracks, vias
1,357, 705
Pours
24
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
5 Apr 2026
Updated
5 Nov 2026

Overview

Spin rig controller is an open-source printed circuit board by Tinkerbug-Robotics, from the Tinkerbug-Robotics/TinkerRocket repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 110 × 80 mm with 170 parts on 126 nets, routed with 1,357 tracks and 705 vias.

It is built around the ESP32-S3FN8, SN74ACT244PWRE4 and SN74LVC2G125DCTR-JSM, with the INA238AIDGSR, TPS54560BDDAR and AP2112K-3.3TRG1 among its other parts. Its parts include 66 resistors, 42 capacitors, 10 diodes, 10 connectors and 9 ICs. It belongs with the ESP32 boards of this library.

Main components

12

README

hardware/tinker-base/README.md

Tinker-Base

Tinker-Base is the product name, from 2026-09-24, of the board this repo called base-station-mini — the one base station in the product line, for both the Tinker-Mantis and the Tinker-Beetle. The board it forked from, the full base-station, is now in ../legacy/.

A reduced-feature ground station. "Mini" means fewer features, not a smaller board — the outline is still base-station's 30.27 × 90.50 mm. Nothing here is trying to shrink; it is trying to do less.

Currently rev V2, in work. V1 was ordered on 2026-09-29 (tinker-base-v1.0.0) and built; see Status.

What it drops, and what it gains

Against base-station/:

  • The LoRa radio is on-board. U16, an E220-900MM22S on SPI, replaces the UART header that fed an external lora-daughterboard/. That removes the daughterboard, its connector, and the 5 V V_LORA boost that supplied it — the module runs straight off +3V3.
  • No external charger sheet. Dropped from the root, along with the PosADC/MidADC sense lines it fed. external_charger.kicad_sch was deleted outright on 2026-08-12 rather than left orphaned on disk.
  • No sensor I²C. SDA_SENS/SCL_SENS are gone, which is what freed GPIO33 and GPIO34 for the radio.
  • +3V3 comes from the adjustable TPS63020 and its feedback divider, R13 1 MΩ over R16 180 kΩ for 3.28 V. base-station moved to the fixed-output TPS63021 at V6; this board went back to the adjustable part on 2026-08-16. The two share a footprint, and the divider is what tells them apart. With the divider, the fixed part would drive about 21 V. V2 replaces both with a fixed 3.3 V TPS62152 buck; see Status.

Parts and patterns taken from the Beetle and Mantis

On 2026-09-27 the ESP32-S3 sheet took on the newer parts the Beetle and Mantis carry, plus the decoupling Espressif's hardware checklist asks for. The layout followed on 2026-09-28; see Status.

  • BLE antenna. U15 is now the edge-mounted 2.4 GHz loop chip antenna (1.0 × 0.5 mm) that both flight computers use, with the same pi match: C7 (5.1 pF) in series, L4 (2.2 nH) to ground on the radio side, and C5, an unfitted shunt on the antenna side kept for tuning. L4 was the old antenna's 4.3 nH shunt and keeps its footprint. The old antenna worked on top of the ground plane; this one needs a keep-out.
    • It sits in a ground band along the board edge (copper from 0.3 to 0.75 mm in from the edge), with its ground pads in the band.
    • Inboard of the band, a window 4.6 mm along the edge and 3.0 mm deep is clear of copper on every layer, including under the feed pads. Only F.Cu has a notch in it, for the feed trace. That is Abracon's evaluation-board layout (rev A p.4), and the Beetle's.
    • Ground vias stitch the far side and both ends.
    • The first layout, on 2026-09-28, cut the notch on every layer and left planes under the feed pads. The design review caught it (L2).
  • Boot flash (V1 only; V2 removes it, see Status). U1 is the Beetle and Mantis's 16 MB quad-SPI NOR in a 24-ball WLCSP. It is fed from +3V3, with C1 (100 nF) beside it, instead of from the S3's VDD_SPI pin. The full base-station's V5 showed why. VDD_SPI sits behind a switch inside the S3. With an in-package-PSRAM S3 on the same pin, the flash's supply budget fails, and every other board already feeds its NOR from the 3.3 V rail. The balls are on a 0.5 mm pitch, but every signal is in the two middle columns. The traces escape through the 0.55 mm gaps beside them at 0.1 mm track and space, below this board's 0.2 mm default. Keep vias out of the ball pads; JLCPCB queried exactly that on the Beetle.
  • VDD_SPI keeps C9 (100 nF) and C10 (10 µF). Espressif asks for 1 µF here, and the Mantis fits that. But the pin is fed through the S3's internal switch (about 14 Ω), which makes it the board's highest-impedance rail, so the extra bulk helps. Espressif's reasons for a small cap don't apply here: the rail still settles well before CHIP_PU releases, and the board never light-sleeps. The LoRa daughterboard's review keeps 10 µF for the same reason (finding 4a).
  • VDD3P3 (pins 2 and 3, behind L3) gains C24, 10 µF, beside C16, as on the Mantis.
  • GPIO0 gains R5, 10 kΩ to +3V3, on top of the S3's weak internal pull-up, as on the Mantis.
  • L_RXEN gains R6, 100 kΩ to ground. GPIO35 has no reset pull, so the radio's receive enable used to float through every reset. Now it is held off until firmware drives it, which is the Beetle's fix for the same line.

From the 2026-09-28 design review:

  • LoRa antenna port gains L5, 330 nH from the SMA line to ground. It is the protective shunt Ebyte's manual asks for (§5.1). J8 moved 1.14 mm to the edge, so the connector's centre pin now covers its whole pad.
  • U9 gains C25, 100 nF from V_SWITCH to the ground pin beside the input pins. That gives the input a short high-frequency loop. The bulk input cap can't provide one, because its ground pad is walled off by the switch-node pours.
  • U9's output gains C26, 100 nF from +3V3 to ground beside the output pins, for the same reason on the output side: the 22 µF caps' ground pads return around the switch-node pour. U9's FB line runs under its body, between the pads. Its ground pad shares a via with U9 pin 2.
  • Charge current: R52 680 Ω → 1.2 kΩ, about 0.45 A (0.40–0.50 A) instead of 0.79 A. The old value sat at the charger's 0.8 A limit, and it made the charger heat the board past its own thermistor's trip point; see the next section.

The battery thermistor is board-mounted, and that is a compromise

TH1 feeds the BQ21040's TS pin, which gates charging on temperature. It is a 10 kΩ-at-25 °C NTC, B25/85 = 3435 K, ±1 % on both, in an 0603 chip package, on the component side at the far end of the board from the charger. R53 (210 kΩ, TS to ground) is TI's TTDM-defeat resistor and is unchanged — with the same resistance-temperature curve the charger's temperature window does not move.

Until 2026-08-27 TH1 was a two-pin 2.54 mm land for a leaded thermistor of that same curve, meant to be taped to the 18650 so TS read cell temperature. The cell holder leaves no room for a part under the cell, so the sensor moved onto the board.

What that costs. The NTC now reads the ground plane, not the cell, and its self-heat bias runs one way: a warm board makes the charger believe the pack is warmer than it is.

  • On the hot side that is conservative — charging is inhibited early.
  • On the cold side it is not. Board self-heat can mask a genuinely cold cell and allow a sub-0 °C charge, which is the failure the TS pin exists to prevent.

Placement mitigates this; it does not remove it. TH1 sits 25 mm from the charger — the dominant heat source while charging, dissipating up to about 0.7 W as a linear regulator at the ~0.45 A R52 programs (up to 1.6 W at the original 0.79 A) — 27 mm from the buck-boost and 15 mm from the ESP32-S3. Weighted by dissipation over distance that is about 37 % less coupling than the old land, which sat 8.6 mm from the buck-boost and 13.5 mm from the charger. A solid inner ground plane keeps the board close to isothermal, so what remains is a board-wide offset rather than a local hot spot.

Everywhere on the board that is further from the heat needs a sensor trace threaded through the ESP32-S3 fanout or the chip antenna's ground-via fence; neither is worth it for a few degrees. The route as built is 19 mm on F.Cu with no vias.

Charging heat reaches TH1 anyway. The solid planes spread the charger's heat, so TH1 reads roughly the board's mean temperature: about +19 K per watt of charger dissipation in still air. The design review modelled this (±25 %).

  • At the original 0.79 A: the charger folds back to about 0.9 W, which trips the 40.6 °C hot threshold from about 25 °C ambient.
  • At 1.2 kΩ: it stays out of thermal regulation, and TH1 rises 11–14 K.
  • With the base station on: its own ~0.3 W adds about 6 K.
  • No power path: the load hangs on the cell node, so while charging is suspended it drains the cell even with USB plugged in.

Two consequences:

  • USB charges the cell; it does not run the base station. Charge with S1 off.
  • The charger's 10-hour safety timer ends a charge that never terminates, because a running board keeps the current above the termination threshold. Only unplugging USB re-arms it.

Open at first article: with the board charging, compare the TS node against a reference probe on the cell at room temperature, near 0 °C and at 35 °C, with S1 off and on, and confirm the offset is small enough to accept. If it is not, the fix is a wired probe on a connector, not a different chip.

The radio pinout is deliberately identical to lora-daughterboard

All eight ESP32↔E220 signals land on the same GPIOs as the fabbed lora-daughterboard, so the radio_board firmware pin map applies unchanged:

netE220GPIO
L_SCK15 SCK17
L_CS14 NSS18
L_MOSI13 MOSI21
L_MISO12 MISO33
L_BUSY11 BUSY34
L_RXEN10 RXEN35
L_RST3 NRST38
L_DI0120 DIO12

L_DI02 is a module-local loop from DIO2 to TXEN, so the SX1262 drives its own RF switch and costs no GPIO. DIO3 is unconnected. Both match the daughterboard.

Provenance

The design started as a copy of base-station and diverges from there. There is no ongoing relationship between them — nothing is shared, nothing tracks upstream, and a change to one is not expected to reach the other. Treat anything still inherited as a first draft to be justified on its own terms.

Two things were deliberately left behind at the fork:

  • base-station's design reviews (prefab-review-2026-08-02.md, power-switch-review-2026-08-02.md) — records of a review of that board. Copying them here would assert this board has been reviewed when it has not. They remain the best reading on the inherited power architecture; read them there.
  • outputs.kicad_sch, an empty sheet in legacy/base-station/ referenced by nothing. See the leftovers note in ../README.md.

Status

In work: in-package flash, a log flash, the USB-C, the LED resistors and the 3.3 V buck (2026-10-29/30)

This is V2. The title blocks on all four sheets and on the PCB say V2. The PCB caught up with the schematic on 2026-10-30; see PCB below.

  • U3 is an ESP32-S3FH4R2, with 4 MB flash and 2 MB PSRAM in the package. The Beetle V2, the Mantis V11 out computer and the LoRa daughterboard V4 moved to the same part on the same day. The symbol and the QFN-56 footprint are unchanged.

  • U1, the WLCSP boot NOR, is gone, along with its 100 nF C1 and the SPI_* nets. Pads 30–35 carry no-connect flags. VDD_SPI keeps C9/C10, because it now feeds the in-package flash and PSRAM.

  • The log flash is U23, a GigaDevice GD25Q128ESIGR (16 MB NOR, SOP-8 208 mil, LCSC C2928891). It sits on the S3's general-purpose SPI at GPIO4–7, pads that V1 left unconnected. The pins and net names match the NAND bus on the V2 base station (board_v2.h, SPI3), so that firmware pin map carries over:

    netU23GPIO
    M_SCK6 CLK4
    M_MOSI5 DI5
    M_FLASH_CS1 /CS6
    M_MISO2 DO7

    R58–R60 (10 kΩ) pull /CS, /WP and /HOLD up to +3V3. /CS keeps the chip deselected while GPIO6 floats through reset. /WP and /HOLD stay high, since the bus is 1-bit SPI. C89 (100 nF) decouples VCC on +3V3. The symbol and footprint are the ones the full base station used for its GD25Q128ESIG (Custom:W25Q128JVSIQ, Footprints:SOIC127P790X216-8N).

  • Why a separate chip: each received packet logs as 75 bytes, about 1.6 MB per hour with three rockets transmitting. The FH4R2's 4 MB leaves about 1.9 MB after two OTA slots, roughly one hour. All 16 MB of U23 holds logs, which is about 8 hours, more than V1's 9.94 MB spiffs partition. At JLC (2026-10-29, qty 100) the FH4R2 is $2.52 and the GD25Q128E is $0.97. JLC stocks neither the RH2 nor the W25Q128JVYIQ.

  • J2 is the GCT USB4110-GF-A (2026-10-30), the right-angle USB-C on the Mantis and the LoRa daughterboard, in place of HRO's TYPE-C-31-M-12. It uses the same Custom:USB4110GFA symbol, so the nets do not change. Its shell is four SMT pads plus two 0.65 mm non-plated pegs, so the hand-soldered shell legs and plated slots go away. The land is bigger than HRO's (courtyard 12.9 × 8.4 mm against 10.6 × 9.4 mm), and its origin sits at the rear pad row rather than the body center. JLC, 2026-10-30, qty 100: $0.88, C5143397, 3,326 in stock (HRO's was $0.15).

  • The LED resistors R41 and R54 are 330 Ω (Yageo RC0402FR-07330RL, C105875), down from 150 Ω. No board in the fleet uses a value between 150 Ω and 1 kΩ, and these two were the only 150 Ω parts, so the BOM keeps the same line count. At a typical 2.0 V drop, D6 (green, from +3V3) runs about 4 mA instead of about 9 mA. D9 (blue, from the battery through U5's CHG) runs about 2–4 mA at a 3.0 V drop instead of 5–8 mA.

  • U9 is a TPS62152RGTR (2026-10-30), the fixed 3.3 V, 1 A buck the Beetle and Mantis use (LCSC C2070611), in place of the TPS63020 buck-boost. R13 and R16 are gone; nothing sets the output any more.

    • Why: the first V1 board, on the bench on 2026-10-30, ran +3V3 at 6.4 V from a 4.05 V cell. Its boot flash died during the first flash and the ESP32-S3 stopped enumerating minutes later. V1's U9 symbol carried a stale SnapEDA field, MP = TPS63021DSJR, beside MPN = TPS63020DSJR, and JLC stocks both. The fixed TPS63021 on this divider runs away (see above). U9's marking has not been read to confirm it.
    • Why a buck is enough: +3V3 now carries only the ESP32-S3 and the E220, about 55–90 mA running and roughly 250–300 mA at peaks. The TPS6215x is specified from 3 V, keeps running to its 2.7 V UVLO, and goes to 100 % duty as the cell nears 3.3 V. With its 120 mΩ high-side switch (at 3 V) and L9's 74 mΩ, it holds 3.3 V down to a cell of about 3.36 V at 300 mA (SLVSAL5E eq. 3). Below that, +3V3 follows the cell, and the S3's 3.0 V minimum ends the run near the firmware's 0 % point (3.00 V). The buck-boost used the cell down to the protection cutoff; the difference is about the last 5–10 % of an 18650.
    • Wiring: as the Beetle's U18, except DEF. PVIN, AVIN and EN are on V_SWITCH, after U22. SW drives L9, the same VLS3012CX-2R2M-1. VOS and FSW are on +3V3 (FSW high is about 1.25 MHz). FB, DEF, AGND, PGND and the pad go to GND. DEF low gives 3.3 V; the Beetle ties DEF to its output for +5 % because its TPS61094 follows the buck. PG is unused and flagged no-connect. C90 (10 nF, CL05B103KB5NNNC) sets the soft start, as the Beetle's C44. The input caps (C59, C29, C23, C25) and output caps (C58, C60–C62, C26) stay. The footprint is the Beetle's Footprints:QFN50P300X300X100-17N.
    • A wrong variant still hurts, less: a TPS62150 (adjustable) or TPS62153 (5 V) in this land, with FB grounded, runs at 100 % duty and puts the cell, up to 4.2 V, on +3V3. That is above the S3's 3.6 V maximum. The fab notes ask for the part by its LCSC code.
    • Checked: in the netlist only U9, R13, R16 and the new C90 change; every other pin keeps its net. ERC loses V1's two U9 errors (the tied VOUT outputs and the open PG) and its lib_symbol_mismatch, and gains only off-grid wire-end warnings. U9 sits on a half-grid point, as before.
  • Checked: the netlist differs from V1 only by this change. ERC has nothing new. The six new power symbols carry the same lib_symbol_mismatch as every other power symbol on the board. The +3V3 net's power_pin_not_driven now names U3 pin 20 instead of U1.

  • PCB (2026-10-30): brought up to this schematic with pcbnew scripts, the footprints linked to their symbols by path as Update PCB links them. kicad-cli pcb drc --schematic-parity finds 0 errors, 0 unconnected items and 0 parity issues, with 26 warnings, as at V1's sign-off. The zones are a fresh fill.

    • Removed: U1, C1, their SPI_* escape traces and vias, U1's +3V3 stub with its two vias, R13 and R16.

    • The buck follows the Beetle's arrangement. U9 is on the QFN-16 land at (50.85, 168.95), turned −90°:

      • SW faces L9 at (52.1, 164.98).
      • PVIN and AVIN face down toward U22.
      • VOS and PGND face the output caps.
      • FB, AGND, FSW and DEF face the board edge.

      The four 22 µF output caps (C58, C60–C62) stand in a column to the right, with their +3V3 pads toward L9 and a ground via beside each ground pad. C59 (22 µF) sits under PVIN. C29 and C25 are beside it on the same V_SWITCH strip, and C23 and C90 are on the left. C26 moved next to the output column, and C88 moved to the right of U22.

      • F.Cu pours: SW joins pins 1–3 to L9 pad 1. +3V3 takes in L9 pad 2, the output caps, VOS and the pull-up ends of R58 and R59. V_SWITCH takes in PVIN, AVIN, EN, the input caps, U22's outputs and R44.
      • Ground: the exposed pad has one via to In1, under JLC's exception to the no-via-in-pad rule for QFN ground pads. PGND, FB, AGND and DEF tie to the pad on F.Cu.
      • FSW has its own via to the In2 +3V3 plane, 0.145 mm clear of In2's VCC trace along the left edge. That trace is why the block sits 0.5 mm right of the old U9.
      • Silk: U9's pin-1 dot lands between U9 and L9, over L9's pad
        1. That gives one silk_over_copper warning and one silk_overlap warning. The fab clips the dot; the F.Fab marker stays.
    • U23 (SOP-8) is at (52.2, 158.95), turned 180°, in the free copper below the antenna's via fence. Its left pads are 0.39 mm from the board edge. C89, R60, R58 and R59 sit in a row under it.

      • Fan-out: GPIO4–7 leave U3's left side at 0.25 mm pitch on 0.127 mm tracks, between C17/C18 and the pads.
      • Layers: MOSI, CS and MISO stay on F.Cu and enter their pins from under the body. SCK would have to cross MOSI, so it drops to B.Cu at (53.4, 154.0) and comes back up beside pin 6. WP runs round the outside to R59.
      • To make room: L_DI01's via moved from (55.66, 152.44) to (55.9, 151.95). Five ground stitching vias went: C17/C18's own via at (55.675, 151.815), two in the fan-out corridor, one that would have sat in U23's ground pad, and one by the crystal. C17/C18's ground via is back at (55.425, 151.6); without it their ground was an island.
      • Volt_Read used to run diagonally on B.Cu under the old buck. It now runs straight down x = 54.2 and turns under U22's top edge, which frees B.Cu under the input caps.
    • J2 is on the GCT land at (63.06, 189.0). The front face of its fab outline is at y = 195.33, the same as HRO's, so the case's USB slot lines up.

      • Traces: the signal pads land within 0.075 mm of HRO's, so the existing traces end inside them.
      • BT2: pad P is 0.838 mm from J2's copper (the A1/B12 pad), against 0.834 mm to HRO's shell on V1. The plated shell slots are gone, and with them two BT2 silk warnings.
  • Not done:

    • PCB: the gerbers and the position file are not re-plotted. That waits for a V2 order.
    • Firmware: a 4 MB partition table, and SPIFFS mounted on an external NOR over SPI3.
    • bom.csv and FABRICATION-NOTES.md, which still describe V1.

V1

V1 was ordered from f85acb89 (tag tinker-base-v1.0.0). The rest of this section describes V1 as ordered. Schematic and PCB are in sync and fully routed, with 0 parity issues, 0 unconnected, no DRC errors and zone fills that match a fresh refill. That was checked on 2026-09-28, after the design review's fixes. The remaining 26 DRC warnings are silkscreen and the logo's library nickname. Layout details worth knowing:

  • R1, the CHIP_PU pull-up, moved beside C8 to free the spot above C16 for C24.
  • CLK and WP cross the other flash lines on B.Cu, through four vias. The flash's ball order and the ESP32's SPI pin order leave no arrangement without a crossing.
  • Ground vias: U3's exposed pad has nine, in the gaps between its paste windows (Espressif asks for at least nine). Nine more sit beside signal vias.
  • S3's body area has no top copper (Mitsumi's "no pattern" zone). Its GPIO0 via moved out from under the switch.
  • J2's signal pads are trimmed at the rear to HRO's own land, which keeps 0.84 mm between the battery's + pad and the connector.
  • Fiducials FID1–FID3 are on the top side.

Firmware: tinkerrocket-idf/projects/base_station built with -DTR_BS_BOARD=4 — the pin map is main/board/board_v4.h, taken from this board's netlist: the radio over SPI on the pins in the table above, no I²C, no pack charger, the cell on V3's divider. It builds but has not run, because no board exists yet; the firmware release keeps shipping the full base station's V3 image in the Tinker-Base slot until a first article proves V4. The V3 image does not run on this board (it drives a lora-daughterboard over UART).

Reviewed 2026-08-12: prefab-review-2026-08-12.md. Its "Verified correct" section is superseded: the Molex antenna and the fixed-output regulator it describes are gone.

Reviewed again 2026-09-28: design-review-2026-09-28.md. Its Fixes applied section lists what was done and what was left, and why. The fabrication and assembly steps are in FABRICATION-NOTES.md. See also Sending a board to fab in ../README.md.

Parts

170
QtyValueFootprintReferences
1510 kResistor_SMD:R_0402_1005MetricR103, R105, R111, R121, R122, R123, R201, R202, R203, R301, R303, R304, R305, R322, R323
13100 nFCapacitor_SMD:C_0402_1005MetricC104, C106, C112, C121, C122, C205, C206, C208, C209, C301, C304, C306, C307
71 kResistor_SMD:R_0402_1005MetricR110, R125, R208, R210, R310, R312, R319
74.7 kResistor_SMD:R_0402_1005MetricR107, R213, R214, R302, R309, R311, R318
61 uFCapacitor_SMD:C_0402_1005MetricC107, C118, C119, C203, C207, C212
6100Resistor_SMD:R_0402_1005MetricR209, R211, R212, R320, R321, R324
64.7 uF 50 VCapacitor_SMD:C_1210_3225MetricC102, C103, C108, C109, C110, C123
4100 kResistor_SMD:R_0402_1005MetricR109, R120, R325, R326
4M3MountingHole:MountingHole_3.2mm_M3H1, H2, H3, H4
4RedLED_SMD:LED_0603_1608MetricD104, D106, D201, D203
31 MResistor_SMD:R_0402_1005MetricR106, R113, R124
31 nFCapacitor_SMD:C_0402_1005MetricC105, C302, C303
310 uFCapacitor_SMD:C_0402_1005MetricC120, C204, C211
3120Resistor_SMD:R_0402_1005MetricR313, R314, R315
333Resistor_SMD:R_0402_1005MetricR306, R307, R308
347 uF 16 VCapacitor_SMD:C_1210_3225MetricC115, C116, C117
35.1 kResistor_SMD:R_0402_1005MetricR118, R204, R205
3FiducialFiducial:Fiducial_1mm_Mask2mmFID1, FID2, FID3
3GNDTestPoint:TestPoint_Pad_D1.5mmTP205, TP206, TP306
212 pFCapacitor_SMD:C_0402_1005MetricC201, C202
220 kResistor_SMD:R_0402_1005MetricR112, R126
2200 kResistor_SMD:R_0402_1005MetricR104, R115
222Resistor_SMD:R_0402_1005MetricR206, R207
233 kResistor_SMD:R_0402_1005MetricR114, R117
2B560CDiode_SMD:D_SMCD103, D105
2B5819WSDiode_SMD:D_SOD-323D107, D108
1+3V3TestPoint:TestPoint_Pad_D1.5mmTP203
1+5VTestPoint:TestPoint_Pad_D1.5mmTP204
10Resistor_SMD:R_0402_1005MetricR316
11.5 AFuse:Fuse_1206_3216MetricF102
110Resistor_SMD:R_0402_1005MetricR108
110 nFCapacitor_SMD:C_0402_1005MetricC210
1100 nF 50 VCapacitor_SMD:C_0402_1005MetricC111
1100 pFCapacitor_SMD:C_0402_1005MetricC305
1100 uF 50 VCapacitor_SMD:CP_Elec_8x10.5C101
115 kResistor_SMD:R_0402_1005MetricR116
12 AFuse:Fuse_1206_3216MetricF101
12 mΩFootprints:R_0805_KelvinR102
12.2 kResistor_SMD:R_0402_1005MetricR119
124 nHInductor_SMD:L_0402_1005MetricL201
1330Resistor_SMD:R_0402_1005MetricR317
14 AFuse:Fuse_1206_3216MetricF103
14.7 nFCapacitor_SMD:C_0402_1005MetricC113
140 MHzFootprints:XTAL_ECS-400-10-37B2-CKY-TRY201
147 kResistor_SMD:R_0402_1005MetricR101
147 pFCapacitor_SMD:C_0402_1005MetricC114
15V AUXConnector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_VerticalJ104
16.8 uHInductor_SMD:L_Sunlord_MWSA1004SL101
1AM26LV32EIDRPackage_SO:SOIC-16_3.9x9.9mm_P1.27mmU302
1AO4264EPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmQ102
1AP2112K-3.3TRG1Package_TO_SOT_SMD:SOT-23-5U105
1BOOTButton_Switch_SMD:SW_Push_1P1T_XKB_TS-1187ASW201
1BRAKE RESConnector_JST:JST_VH_B2P-VH_1x02_P3.96mm_VerticalJ102
1BZT52C12Diode_SMD:D_SOD-123D101
1CL57T CONTROLConnector_JST:JST_PH_B10B-PH-SM4-TB_1x10-1MP_P2.00mm_VerticalJ301
1DBG_RXTestPoint:TestPoint_Pad_D1.5mmTP202
1DBG_TXTestPoint:TestPoint_Pad_D1.5mmTP201
1DRIVERConnector_JST:JST_VH_B2P-VH_1x02_P3.96mm_VerticalJ103
1ENCODERConnector_JST:JST_PH_B8B-PH-SM4-TB_1x08-1MP_P2.00mm_VerticalJ302
1ENC_ATestPoint:TestPoint_Pad_D1.5mmTP303
1ESP32-S3FN8Footprints:IC_ESP32-S3U201
1EVENTA_OUTTestPoint:TestPoint_Pad_D1.5mmTP304
1GNSSConnector_JST:JST_PH_B3B-PH-SM4-TB_1x03-1MP_P2.00mm_VerticalJ304
1INA238AIDGSRPackage_SO:MSOP-10_3x3mm_P0.5mmU101
1INDEXTestPoint:TestPoint_Pad_D1.5mmTP305
1INDEXConnector_JST:JST_PH_B4B-PH-SM4-TB_1x04-1MP_P2.00mm_VerticalJ303
1NCE60P50KPackage_TO_SOT_SMD:TO-252-2Q101
1PACK INConnector_JST:JST_VH_B2P-VH_1x02_P3.96mm_VerticalJ101
1PIConnector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ202
1PPSTestPoint:TestPoint_Pad_D1.5mmTP302
1PUL_PTestPoint:TestPoint_Pad_D1.5mmTP301
1QWIICConnector_JST:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_VerticalJ203
1RESETButton_Switch_SMD:SW_Push_1P1T_XKB_TS-1187ASW202
1SMCJ30ADiode_SMD:D_SMCD102
1SN74ACT244PWRPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmU301
1SN74LVC1G17DBVRPackage_TO_SOT_SMD:SOT-23-5U303
1SN74LVC2G125DCTRPackage_SO:SSOP-8_2.95x2.8mm_P0.65mmU304
1SP0503BAHTGFootprints:TVS-SP05_LTFCR201
1TLV3011AIDBVRPackage_TO_SOT_SMD:SOT-23-6U102
1TPS54560BDDARPackage_SO:Texas_R-PDSO-G8_EP2.95x4.9mm_Mask2.4x3.1mmU104

The 167 most common of 170 parts.

More from Tinkerbug-Robotics/TinkerRocket

11
  • 8 layers22.3 × 77.5 mmTinker mantis, the printed circuit board in 3D

    Tinker mantis

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    279 parts1GPL-3.0
  • 8 layers22.5 × 69.6 mmTinker beetle, the printed circuit board in 3D

    Tinker beetle

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    227 parts1GPL-3.0
  • 6 layers35 × 35 mmSpace bug m8t, the printed circuit board in 3D

    Space bug m8t

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    116 parts1GPL-3.0
  • 4 layers30.3 × 90.5 mmBase station, the printed circuit board in 3D

    Base station

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    115 parts1GPL-3.0
  • 4 layers30.3 × 90.5 mmTinker base, the printed circuit board in 3D

    Tinker base

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    94 parts1GPL-3.0
  • 4 layers28.3 × 30.8 mmGnss px100-18mm hv, the printed circuit board in 3D

    Gnss px100-18mm hv

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    85 parts1GPL-3.0
  • 6 layers22 × 27.5 mmLora daughterboard, the printed circuit board in 3D

    Lora daughterboard

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    74 parts1GPL-3.0
  • 4 layers22 × 30 mmGnss px1105r-18mm hv, the printed circuit board in 3D

    Gnss px1105r-18mm hv

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    52 parts1GPL-3.0
  • 6 layers22 × 27.5 mmGnss sam10m8-18mm hv, the printed circuit board in 3D

    Gnss sam10m8-18mm hv

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    26 parts1GPL-3.0
  • 4 layers24.4 × 16.4 mmServo adapter, the printed circuit board in 3D

    Servo adapter

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    14 parts1GPL-3.0

Similar boards

  • 4 layers74 × 90 mmBay node, the printed circuit board in 3D

    Bay node

    kartben/hw-testing-rack

    3D-printed, tilted test shelf for 16 dev boards: sliding drawers, per-bay ESP32-S3 running Zephyr (USB/IP, power switching, metering), KiCad PCBs, OpenSCAD parts, BOM and an interactive 3D viewer

    135 parts
  • 2 layers154.5 × 105 mmInterface brain, the printed circuit board in 3D

    Interface brain

    ademuri/colordance-circle

    An art project that uses arrays of colored lights around a circle to create kaleidoscopic colored shadows.

    174 parts4Apache-2.0
  • 2 layers200 × 120 mmPlytka v2, the printed circuit board in 3D

    Plytka v2

    tmierzwa/WICI

    Otwarty system łączności awaryjnej (Reticulum/LXMF, 869 MHz)

    152 parts4
  • 4 layers70 × 50 mmMjpower ss, the printed circuit board in 3D

    Mjpower ss

    mjbots/power_dist

    This repository contains hardware and firmware for the mjbots powerdist and mjpower-ss boards. Both provide pre-charge, over-current limiting and connector fanout.

    35 parts15Apache-2.0
  • 2 layers119.9 × 57 mm1v2boost, the printed circuit board in 3D

    1v2boost

    benkrasnow/1v2-boost-converter

    Schematics and PCB layout for a boost converter 0.9V minimum input, 30A maximum input current

    77 parts7MIT
  • 2 layers90 × 100 mmHost shell, the printed circuit board in 3D

    Host shell

    shapoco/wildcardboy

    Handheld Game Console with Replaceable MCU

    241 parts5
  • 6 layers216 × 127 mmPufferfish Controller-1, the printed circuit board in 3D

    Pufferfish Controller-1

    pez-globo/pufferfish-electronics

    Circuit schematics and PCB layouts for the Pufferfish ventilator.

    559 parts3
  • 2 layers100 × 85 mmDekatron, the printed circuit board in 3D

    Dekatron

    kuvychko/universal-nixie-display

    Six IN-14 Nixie tubes, an A101 dekatron and an ESP32 touchscreen in one desktop display: a clock, timer and toy, and a numeric display for a computer over USB.

    165 parts1

Questions

How big is the Spin rig controller PCB?

It measures 110 × 80 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Spin rig controller use?

170 parts, built around the ESP32-S3FN8, SN74ACT244PWRE4, SN74LVC2G125DCTR-JSM and INA238AIDGSR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Spin rig controller KiCad files?

From the Tinkerbug-Robotics/TinkerRocket repository on GitHub, at the commit this page was made from: the board is hardware/spin-rig-controller/spin-rig-controller.kicad_pcb and its schematic hardware/gnss-px100-18mm-hv/gnss-px100-18mm-hv.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Spin rig controller design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).