Skip to the content
2 layers24 × 73.5 mmPico eth, the printed circuit board in 3D

Pi pico / Pi pico2 hat with LAN8720 Ethernet PHY wihtout MDIO

Size
24 × 73.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
30
Nets
57
Pads
189
Tracks, vias
225, 76
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
2 Jun 2025
Updated
2 Jun 2025

Overview

Pico eth is an open-source printed circuit board by thomasfla, from the thomasfla/pico-lan8720-minimal repository on GitHub, published under the BSD-3-Clause licence. It is a 2-layer board of 24 × 73.5 mm with 30 parts on 57 nets, routed with 225 tracks and 76 vias.

It is built around the LAN8720A-CP. Its parts include 20 resistors, 5 capacitors, 2 ICs and 1 connector. It belongs with the RP2040 boards of this library.

Main components

1

README

README.md

pico-lan8720-minimal

Pi pico / Pi pico2 hat with LAN8720 Ethernet PHY wihtout MDIO

View PCB online

picture of the boards

Parts

30
QtyValueFootprintReferences
733Resistor_SMD:R_0402_1005MetricR12, R19, R21, R22, R23, R24, R25
610kResistor_SMD:R_0402_1005MetricR13, R14, R15, R16, R17, R18
449.9Resistor_SMD:R_0402_1005MetricR5, R6, R7, R8
3100nCapacitor_SMD:C_0402_1005MetricC7, C8, C9
2330Resistor_SMD:R_0402_1005MetricR10, R11
112.1kResistor_SMD:R_0402_1005MetricR9
11u LOW ESRCapacitor_SMD:C_0402_1005MetricC6
122nCapacitor_SMD:C_0402_1005MetricC5
1FerriteBeadInductor_SMD:L_0402_1005MetricFB1
1LAN8720APackage_DFN_QFN:VQFN-24-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalViasU2
1PicoMCU_RaspberryPi_and_Boards:RPi_Pico_SMD_THU1
1RJ45_Pulse_JXD6-0001NLConnector_RJ:RJ45_Pulse_JXD6-0001NL_HorizontalJ5

The 29 most common of 30 parts.

Similar boards

  • 2 layers85 × 56 mmHB RF ETH, the printed circuit board in 3D

    HB RF ETH

    alexreinert/PCB

    Some of my PCBs

    96 parts104
  • 4 layers110 × 110 mmSmoothiev2-prime, the printed circuit board in 3D

    Smoothiev2-prime

    Smoothieware/Smoothieboard2

    Hardware files for the Smoothieboard v2, and extension boards

    453 parts71
  • 4 layers102.6 × 107.3 mmPro rev1, the printed circuit board in 3D

    Pro rev1

    TheRetroWeb/PicoPOST

    RPi Pico based POST (Power-On Self Test) Diagnostic Card

    136 parts58
  • 2 layers50.8 × 20.3 mmEthernet pmod, the printed circuit board in 3D

    Ethernet pmod

    swetland/ethernet-pmod

    Ethernet PHY PMOD (Microchip LAN8720A PHY)

    26 parts53
  • 4 layers160 × 73.2 mmMainPCB, the printed circuit board in 3D

    MainPCB

    doppelgrau/esp32-f9p-io-board

    An IO-PCB (two motor-driver/H-bridge, CAN, RS232, ADS1115, relay, ethernet, ardusimple f9p compatible connector) with an ESP32 for 12V power, three 15V tolerant analog inputs, three 5V tolerant inputs.

    162 parts39
  • 2 layers40 × 68 mmMULTIGW, the printed circuit board in 3D

    MULTIGW

    nuclearcat/ESP32ETH

    Simple ESP32 with native ethernet using LAN8720 phy, Arduino compatible

    32 parts30LGPL-2.1
  • 4 layers85 × 56 mmNano, the printed circuit board in 3D

    Nano

    EnzoRF/nanoberry

    Single-board computer based on i.MX6 ULL

    229 parts21GPL-3.0

Questions

How big is the Pico eth PCB?

It measures 24 × 73.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Pico eth use?

30 parts, built around the LAN8720A-CP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pico eth KiCad files?

From the thomasfla/pico-lan8720-minimal repository on GitHub, at the commit this page was made from: the board is pico_eth.kicad_pcb and its schematic pico_eth.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pico eth design in my own project?

Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).