
Sheet1
motor-and-motion-control-lab/mmlab-12PhaseDrive-388Slave
PCB Electronics for Humanoid Robots and Bearingless Motor Systems

Small STM32 based ethernet connected radio puck capable of full duplex transmit and receive as well as dual RX or dual TX. Capable of rates up to 1 Mbps and completely configurable for many kinds of different modes. This radio puck has been primarily designed to be your rubber duck that transmits a known signal while prototyping a receiver.
Radio Project is an open-source printed circuit board by thomas-montano, from the thomas-montano/Radio_Puck repository on GitHub. It is an 8-layer board of 100 × 70 mm with 154 parts on 216 nets, routed with 556 tracks and 184 vias.
It is built around the STM32F407VGT6, SI4468-A2A-IM and ADP2164ACPZ-3.3-R7, with the DP83822IRHBR, SIT1566AC-JV-XXE-32.768D and CMD17-21VGD/TR8 among its other parts. Its parts include 70 resistors, 44 capacitors, 15 inductors, 9 diodes and 6 ICs. It belongs with the radio and wireless boards and the STM32 boards of this library.
Small STM32 based ethernet connected radio puck capable of full duplex transmit and receive as well as dual RX or dual TX. Capable of rates up to 1 Mbps and completely configurable for many kinds of different modes. This radio puck has been primarily designed to be your rubber duck that transmits a known signal while prototyping a receiver.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 44 | 40 | Resistor_SMD:R_0402_1005Metric | R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25 +28 |
| 25 | 100nF | C0402C104J8RACTU:CAPC10555_55N_KEM-L | C1, C2, C10, C11, C12, C13, C14, C16, C19, C20, C23, C24, C25, C26, C39, C40 +9 |
| 9 | 60 | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R5, R6, R7, R8, R43 |
| 9 | CMD17-21VGD/TR8 | CMD17_21VGD_TR8:LED0805N_CML-M | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8, LED9 |
| 6 | 49.9 | Resistor_SMD:R_0402_1005Metric | R63, R64, R65, R66, R69, R70 |
| 4 | 11nH | Inductor_SMD:L_0402_1005Metric | L10, L11, L14, L15 |
| 4 | 22nH | Inductor_SMD:L_0402_1005Metric | L6, L7, L12, L13 |
| 4 | 3.3pF | Capacitor_SMD:C_01005_0402Metric | C35, C36, C37, C38 |
| 2 | 100 pF | 0603ZA101FAT2A:CAPC1608X90N | C21, C22 |
| 2 | 100k | Resistor_SMD:R_0402_1005Metric | R31, R32 |
| 2 | 100nH | Inductor_SMD:L_0402_1005Metric | L2, L4 |
| 2 | 132225 | 132225:CONN_132225_AMP | J3, J4 |
| 2 | 18nH | Inductor_SMD:L_0402_1005Metric | L3, L5 |
| 2 | 1K | Resistor_SMD:R_0402_1005Metric | R37, R38 |
| 2 | 1pF | Capacitor_SMD:C_01005_0402Metric | C30, C32 |
| 2 | 2.2uF | 0805ZC225KAT2A:CAPC2012X140N | C3, C4 |
| 2 | 2.49k | Resistor_SMD:R_0402_1005Metric | R67, R68 |
| 2 | 3.3nH | Inductor_SMD:L_0402_1005Metric | L8, L9 |
| 2 | 3pF | Capacitor_SMD:C_01005_0402Metric | C27, C28 |
| 2 | 4.7pF | Capacitor_SMD:C_01005_0402Metric | C29, C31 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R41, R42 |
| 2 | 6.2nF | Capacitor_SMD:C_01005_0402Metric | C33, C34 |
| 2 | SI4468-A2A-IM | SI4468_A2A_IM:QFN50P400X400X90-21N | U4, U5 |
| 2 | TG2520SMN 30.0000M-MCGNNM0 | TG2520SMN:TG2520SMN | Y1, Y2 |
| 1 | 10 | Resistor_SMD:R_0402_1005Metric | R39 |
| 1 | 100uF | C3225X5R0J107M250AB:CAP_C3225X5R0J107M250AB | C17 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R40 |
| 1 | 208-4 | 208-4:DIP8_208-4_CTS | SW1 |
| 1 | 330uF | TRME337K010R0035:CAPPM7343X310N | C18 |
| 1 | 4.87k | Resistor_SMD:R_0402_1005Metric | R50 |
| 1 | 47uF | C3225X5R0J476M250AA:CAP_C3225X5R0J476M250AA | C15 |
| 1 | ADP2164ACPZ-3.3-R7 | ADP2164ACPZ_3_3_R7:QFN65P400X400X80-17N | U3 |
| 1 | DP83822IRHBR | DP83822IRHBR:IC_DP83822IRHBR | U6 |
| 1 | FTSH-105-X-X-DV-007-P-X | FTSH-105-01-L-DV-007-K:SAMTEC_FTSH-105-X-X-DV-007-P-X | J1 |
| 1 | MSS1038-152NLC | Inductor_SMD:L_Coilcraft_MSS1038-XXX | L1 |
| 1 | SIT1566AC-JV-XXE-32.768D | SIT1566AC_JV_XXE_32_768D:BGA_E-32.768D_SIT | U2 |
| 1 | SIT5000AICGE-25MHz | SIT5000AICGE_33N0_25_000000Y:SIT5000_2.7x2.4_SIT-M | XTAL1 |
| 1 | STM32F407VGT6 | Package_QFP:LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | TL3305AF160QG | TL3305AF160QG:SW_TL3305AF160QG | S1 |
| 1 | USB_C_Receptacle | Connector_USB:USB_C_Receptacle_Amphenol_12401548E4-2A | J2 |
| 1 | WE-RJ45_7499010211A | 7499010211A:7499010211A | J5 |

motor-and-motion-control-lab/mmlab-12PhaseDrive-388Slave
PCB Electronics for Humanoid Robots and Bearingless Motor Systems


ajefferies2/t1conv
100BASE-T1 ↔ 100BASE-TX media converter + dual CAN FD/USB adapter on one board.


max7d3/CH32V003-MiniGameConsole
Despite memory limitations, it runs games with full 16-bit color\ graphics at 30 FPS (It can technically hit 60 FPS in all example games, but I designed them for 30, so I locked it there.) It supports either terminal…



clarkmcc/my-first-linux-board
my-first-linux-board is a small F1C200S Linux board built around removable microSD storage, USB-C power and USB device data, a 3.3 V UART console, and power/status LEDs.
It measures 100 × 70 mm and has 8 copper layers, 1.18 mm thick.
154 parts, built around the STM32F407VGT6, SI4468-A2A-IM, ADP2164ACPZ-3.3-R7 and DP83822IRHBR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the thomas-montano/Radio_Puck repository on GitHub, at the commit this page was made from: the board is Hardware/Radio Project.kicad_pcb and its schematic Hardware/ExternalConnectors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask thomas-montano before reusing the design.