Skip to the content
2 layers30.5 × 37.3 mmAddon MH Z19, the printed circuit board in 3D

small functional CO2-sensor based on attnode v3 and MH-Z19

Size
30.5 × 37.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
12
Pads
50
Tracks, vias
126, 14
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
7 Feb 2021
Updated
30 May 2021

Overview

Addon MH Z19 is an open-source printed circuit board by theArcher73, from the theArcher73/attnode-addon_mh-z19 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 30.5 × 37.3 mm with 14 parts on 12 nets, routed with 126 tracks and 14 vias.

It is built around the WS2812B. Its parts include 5 connectors, 3 diodes, 2 capacitors, 1 resistor and 1 IC. It belongs with the sensors and measurement boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

CO2-Sensor-Attnode mit MH-Z19

A small functional AddOn CO2-Sensor to use with a attno.de v3 and MH-Z19-CO2-Sensor

pictures from @seiichiro0185 
MH-Z 19 offen 
MH-Z 19MH-Z 19

You can find more information and the latest firmware at attno.de v3. @seiichiro0185 is continuously developing the software, which is why it is only linked here.

This pcb allows the extension of the attno.de v3 with the possibility to be operated with 5V-15V operating voltage as well as CO2 measurement by means of MH-Z19.

The measured values of the CO2 sensor as well as the connection via LORAWAN(TM) can be visualized directly at the device by the integrated RGB-LED's, parallel to the transmission to a LoRa-Network-Server (LNS).

The use of the MH-Z19C is strongly recommended. However, this sensor drifts over time so regular calibration is required. The sensor can be purchased over the Silk Road or directly from German dealers.

Special thanks to @seiichiro0185, @TwentySixer and @nottheedge for their support.

front viewrear view
front viewRear view

In the folder 3d-files are stl-Files for a tiny housing from @seiichiro.

front-part MH-Z19Crear-part CO2-Sensor Micro-USBrear-part CO2-Sensor USB-C
MH-Z 19 front partCO<sub>2</sub>-Sensor rear part USB MicroCO<sub>2</sub>-Sensor rear part USB Micro
 passende Breakout-Boards Micro-USBpassende Breakout-Boards USB-C

The rear parts of the enclosures for Micro-USB or USB-C are planned for the use of ready-made breakout boards with USB-C or micro USB. The button for ad-hoc measurements or calibration can be glued into the housing.

LORAWAN is a registered trademark of Semtech

Disclaimer

The documentation of the CO2-Sensor-Attnode mit MH-Z19 is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

Parts

14
QtyValueFootprintReferences
21uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1, C2
2WS2812BLED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mmD2, D3
2attnodeConnector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ1, J2
11N4148Diode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1
14k7Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1
1LOGOLogo_attnode:Logo_druckG***
1MCP1703TMCP1703T-3302E_CB:SOT95P255X145-3NU2
1MZ-H19Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ3
1MZ-H19Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ4
1SM04B-SRSS-TBT(LF)(SN)JST-SM04B-SRSS-TB_LF__SN:JST_SM04B-SRSS-TB(LF)(SN)J5

The 13 most common of 14 parts.

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers26 × 30 mmMicrocontroller, the printed circuit board in 3D

    Microcontroller

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    34 parts1.1kCC-BY-4.0
  • 4 layers82.6 × 82.5 mmJumperless2, the printed circuit board in 3D

    Jumperless2

    Architeuthis-Flux/Jumperless

    A jumperless breadboard

    208 parts914
  • 2 layers95.3 × 161.9 mmDfh badge, the printed circuit board in 3D

    Dfh badge

    tanaes/whopping_Voron_mods

    135 parts787GPL-3.0
  • 2 layers42.8 × 28.8 mmMM Skirt, the printed circuit board in 3D

    MM Skirt

    PrintersForAnts/Micron

    If you want to purchase full kits there are 3 available (Kits are slowly updating to R1 hardware just make sure to double check the included hardware in your kit and if you have any questions reach out in the discord)

    11 parts741GPL-3.0
  • 2 layers149.6 × 127.1 mmErgodash, the printed circuit board in 3D

    Ergodash

    omkbd/ErgoDash

    keyboard

    187 parts732MIT
  • 2 layers285.5 × 95 mmReviung46 ver1 1, the printed circuit board in 3D

    Reviung46 ver1 1

    gtips/reviung

    The REVIUNG41 is 41-key column staggered keyboard.

    119 parts517MIT
  • 2 layers177.7 × 144.5 mmCOMM PANEL, the printed circuit board in 3D

    COMM PANEL

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    275 parts431

Questions

How big is the Addon MH Z19 PCB?

It measures 30.5 × 37.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Addon MH Z19 use?

14 parts, built around the WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Addon MH Z19 KiCad files?

From the theArcher73/attnode-addon_mh-z19 repository on GitHub, at the commit this page was made from: the board is kicad-project/addon_MH-Z19.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Addon MH Z19 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).