

Jumperless2
A jumperless breadboard
- Size
- 82.6 × 82.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 208
- Nets
- 354
- Pads
- 1,559
- Tracks, vias
- 7,507, 741
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 25 Mar 2023
- Updated
- 10 Sep 2026
Overview
Jumperless2 is an open-source printed circuit board by Architeuthis-Flux, from the Architeuthis-Flux/Jumperless repository on GitHub. It is a 4-layer board of 82.6 × 82.5 mm with 208 parts on 354 nets, routed with 7,507 tracks and 741 vias.
It is built around the RP2040, INA219AID and LM324, with the L272D, LT1054CP and W25Q128JVSIQ among its other parts. Its parts include 90 diodes, 25 capacitors, 24 resistors, 11 ICs and 5 connectors. It belongs with the RP2040 and AVR (ATmega, ATtiny) boards of this library.
Main components
9RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)INA219AID
SOIC-8-40℃~+125℃ 0.1uV/℃ 0V~26V 1 10uV 120dB 20nA 3V~5.5V 700uA Bidirectional detection、Zero drift / auto-zero、Input filter、Power monitoring、Digital output interface ±26V SOIC-8 Current Sense Amplifiers ROHSTexas InstrumentsCurrent Sense AmplifiersLM324
SOP-14-1.5V~10V 0℃~+70℃ 24V 250nA 3V~20V 4 40mA 50nA 700uA 7mV 80dB SOP-14 Operational Amplifier ROHSHXY MOSFETOperational AmplifierL272D
SOIC-16Dual Power Operational AmplifierSTMicroelectronicsOperational AmplifierLT1054CP
PDIP-8-5V 0℃~+70℃ 100mA 10Ω 2.5mA 25kHz 3.5V~15V Inverted Low-power standby、Adaptive switching frequency PDIP-8 Charge Pumps ROHSTexas InstrumentsDC-DC ConvertersW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedCH446Q
LQFP-44(10x10)-40℃~+85℃ -7V、4V~12V、5V 128 12ns 25pF 45Ω 50MHz LQFP-44(10x10) Analog Switches, Multiplexers ROHSWCH (Nanjing Qinheng Microelectronics)Analog Switches, MultiplexersABLS-12.000MHZ-B4-T
HC-49S-SMD-20℃~+70℃ 12MHz 18pF 50Ω ±30ppm ±50ppm HC-49S-SMD Crystals ROHSAbraconCrystals
README
README.mdJumperless
a jumperless breadboard
If you want one of these, they're available in my Tindie store
There's now a way cooler version, Jumperless V5
You can get a V5 on Crowd Supply
Getting started using your Jumperless
(at this point some of the stuff in that guide is a bit out of date, but generally is good advice)
(You can click on this to watch the explainer video)
Using a bunch of analog crosspoint switches wired together into one bigger switch, this breadboard makes real, hardware connections between any points on the board or the Arduino Nano header at the top via software command, instead of needing to use jumper wires.
3D Printable Stand (you can drop the model through the build plate to adjust the height)
3D Printable Jumperless Trap (jk it's a carrying case, but make sure you can get it back open before you put your Jumperless in it)
Try this Wokwi project if something isn't working: https://wokwi.com/projects/389569655762010113
Here's an example of me using this thing to connect some I2C pins from an Arduino to an OLED
https://github.com/Architeuthis-Flux/Jumperless/assets/20519442/0da0fdcb-c629-4f16-8638-6fab5f5c69fc
Jumperless also has a ton of voltage/current sensing so the RGB LEDs underneath each row can show a ton of information about what's going on with your circuit. 2 buffered high-current DACs (one 0-5V and one ±8V), 4 buffered and level-shifted 12-bit ADCs (3 are 0-5V and 1 for ±8V), 2 INA219 current and voltage measurement ICs, and 4 GPIO to simulate digital or analog signals that can be routed to anywhere on the breadboard or the Arduino Nano header.
https://github.com/Architeuthis-Flux/Jumperless/assets/20519442/e701d5c8-2349-49a1-8d57-8574962e7c29
Use it to probe the pins on an unknown IC (which is what I'm doing in the video above), or for some automated fuzzing, or to help guide you through converting a schematic to a real circuit, or do whatever the hell you want with it.
The connections are real and fully analog (-8V to +8V, up to around 1 MHz before signal quality starts to degrade) instead of cheating with some measure-then-simulate setup, although you can do that too if you want to simulate a memristor or to send jumpers over the internet.
https://github.com/Architeuthis-Flux/Jumperless/assets/20519442/2c203686-e02e-4a0c-b5eb-0cab925386fb
If you want to read about how the code and stuff works, the README in JumperlessNano goes through how each part works in more detail.
Or check out the Hackaday.io page and the Hackaday Blog Writeup
And no, it's not an FPGA.
Here it is running a 555 circuit (note that this is a Rev 1 without the through-PCB LEDs)
https://github.com/Architeuthis-Flux/Jumperless/assets/20519442/9c5d2b5a-3727-4197-b1d0-bd45b5f95559
Here are some fun bonus shots
https://github.com/Architeuthis-Flux/Jumperless/assets/20519442/b933e817-c6e4-4d97-9fc0-7b8d9e875ebb SchematicRevision3.pdf
https://github.com/Architeuthis-Flux/Jumperless/assets/20519442/d070d99d-b6b3-43e3-adee-4ca2d7358a9a
Parts
208| Qty | Value | Footprint | References |
|---|---|---|---|
| 80 | WS2812B | JumperlessFootprints:LED_WS2812B-2020_PLCC4_2.0x2.0mm | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +64 |
| 12 | CH446Q | JumperlessFootprints:LQFP44_Tight | A2, B1, C26, D70, E1, F5, G1, H1, I1, J6, K1, L1 |
| 7 | 1u | Capacitor_SMD:C_0402_1005Metric | C9, C11, C12, C18, C19, C20, C21 |
| 6 | 27p | Capacitor_SMD:C_0402_1005Metric | C13, C14, C17, C22, C23, C24 |
| 6 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3, FID4, FID5, FID6 |
| 6 | Jumper_2_Bridged | JumperlessFootprints:SolderJumper_2_Bridged_Small | JP3, JP7, JP9, JP10, JP13, JP14 |
| 5 | 1K | Resistor_SMD:R_0402_1005Metric | R6, R8, R10, R24, R25 |
| 5 | 1N5819 | Diode_SMD:D_SOD-323 | D61, D62, D65, D67, D68 |
| 5 | 2K | Resistor_SMD:R_0402_1005Metric | R21, R22, R23, R26, R27 |
| 4 | 1N4148 | Diode_SMD:D_SOD-323 | D63, D64, D66, D69 |
| 3 | 100uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C4, C6 |
| 3 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-6032-20_AVX-F_Pad2.25x2.35mm_HandSolder | C2, C3, C5 |
| 3 | 47K | Resistor_SMD:R_0402_1005Metric | R15, R16, R19 |
| 3 | 68K | Resistor_SMD:R_0402_1005Metric | R17, R18, R20 |
| 3 | SolderJumper_2_Bridged | JumperlessFootprints:SolderJumper_2_Bridged_Small | JP4, JP5, JP8 |
| 2 | .33uF | Capacitor_SMD:C_0402_1005Metric | C10, C15 |
| 2 | 10u | Capacitor_SMD:C_0603_1608Metric | C7, C8 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C16, C25 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R5, R12 |
| 2 | 21K | Resistor_SMD:R_0402_1005Metric | R13, R14 |
| 2 | 22R | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | 2Ω | Resistor_SMD:R_0603_1608Metric | R1, R4 |
| 2 | INA219 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4, U6 |
| 2 | LED DOUT | JumperlessFootprints:PINHEADER-1x1_vertical | TP20, TP21 |
| 2 | LM324 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U7, U11 |
| 2 | MCP4725 | Package_TO_SOT_SMD:SOT-23-6 | U3, U5 |
| 2 | TestPoint | Symbol:BackMaskWindows | TP22, TP23 |
| 1 | +-8V DAC | JumperlessFootprints:TestPoint_D0.75mm | TP8 |
| 1 | +8V | JumperlessFootprints:TestPoint_D0.75mm | TP14 |
| 1 | -8V | JumperlessFootprints:TestPoint_D0.75mm | TP13 |
| 1 | 0-5V DAC | JumperlessFootprints:TestPoint_D0.75mm | TP7 |
| 1 | 5V | JumperlessFootprints:PINHEADER-1x1_vertical | J14 |
| 1 | ABLS-12.000MHZ-B4-T | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | ADC 0 IN | JumperlessFootprints:TestPoint_D0.75mm | TP9 |
| 1 | ADC 1 IN | JumperlessFootprints:TestPoint_D0.75mm | TP10 |
| 1 | ADC 2 IN | JumperlessFootprints:TestPoint_D0.75mm | TP11 |
| 1 | ADC 3 IN | JumperlessFootprints:TestPoint_D0.75mm | TP12 |
| 1 | Arduino_Nano_v3.x | JumperlessFootprints:Arduino_Nano | A1 |
| 1 | Breadboard | JumperlessFootprints:Breadboard_CustomClips_Fallback | J4 |
| 1 | Conn_01x04_Pin | JumperlessFootprints:GPIO_header | J7 |
| 1 | Debug | JumperlessFootprints:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | FB/SHDN | JumperlessFootprints:TestPoint_D0.75mm | TP5 |
| 1 | GPIO 16 | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | GPIO 17 | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | GPIO 18 | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | GPIO 19 | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | L272D | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U10 |
| 1 | LED | LED_SMD:LED_PLCC2_reversemount | D91 |
| 1 | LED DIN | JumperlessFootprints:TestPoint_Pad_D1.0mm | TP17 |
| 1 | LED DOUT | JumperlessFootprints:TestPoint_Pad_D1.0mm | TP15 |
| 1 | LT1054 | JumperlessFootprints:DIP-8_W7.62mm | U1 |
| 1 | NANO 3V3 | JumperlessFootprints:SolderJumper_2_Bridged_Small | JP1 |
| 1 | NANO 5V | JumperlessFootprints:SolderJumper_2_Bridged_Small | JP2 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | RP2040 | RP2040_minimal:RP2040-QFN-56 | U9 |
| 1 | SW_DP3T | JumperlessFootprints:Slide_Switch_SSSS223600 | SW2 |
| 1 | USB BOOT | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | USB_B_Mini | JumperlessFootprints:USB_Mini-B_Wuerth_65100516121_Horizontal | J5 |
| 1 | VREF | JumperlessFootprints:TestPoint_D0.75mm | TP6 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U8 |
More from Architeuthis-Flux/Jumperless
3- 4 layers82.6 × 82.6 mm

- 4 layers82.6 × 82.5 mm

- 2 layers50.4 × 24.8 mm

Similar boards
- 4 layers82.6 × 82.6 mm

- 4 layers82.6 × 116.7 mm

- 2 layers475 × 139.9 mm

Skogaslider main pcb
skogaby/skogaslider
Firmware, CAD, and PCB files for the skogaslider, an RP2040-based controller to simulate Chunithm's gameplay experience
175 parts18MIT - 2 layers62.1 × 65.9 mm

RP2040 minimal
gamaPhy/Freedom
Design files of our hall effect sensor analog keypads
40 parts3CERN-OHL-S-2.0 - 4 layers76 × 50 mm

Wigglecam
jadenrhee/wigglecam-controller
RP2040 co-processor board for a 4-lens wigglegram camera: constant-current flash, controls, battery telemetry, Pi 5 I2C interface. 4-layer, DRC-clean, fab-ready.
105 parts - 2 layers116.8 × 92.2 mm

- 4 layers401.3 × 203.2 mm

Cpu010
thorpej/pg68k
The 68k Playground, a 680x0-based home-brew computer with multiple CPU options
272 parts15 - 6 layers91.4 × 92.5 mm

PCB CableUndefined1stPrototype 2024-02-18
Ne-Se-Chete/CableUndefined-Embedded
AI-powered intelligent breadboard that digitally routes circuit connections using an STM32-controlled multiplexer matrix
218 parts1
Questions
How big is the Jumperless2 PCB?
It measures 82.6 × 82.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Jumperless2 use?
208 parts, built around the RP2040, INA219AID, LM324 and L272D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Jumperless2 KiCad files?
From the Architeuthis-Flux/Jumperless repository on GitHub, at the commit this page was made from: the board is Hardware/KiCAD/Jumperless Rev 2/Jumperless2.kicad_pcb and its schematic Hardware/KiCAD/Jumperless Rev 1/JumperlessRev1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Jumperless2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Architeuthis-Flux before reusing the design.

