Skip to the content
12345678

INA219AID

Texas InstrumentsExtended

-40℃~+125℃ 0.1uV/℃ 0V~26V 1 10uV 120dB 20nA 3V~5.5V 700uA Bidirectional detection、Zero drift / auto-zero、Input filter、Power monitoring、Digital output interface ±26V SOIC-8 Current Sense Amplifiers ROHS

Part id
ti/INA219AID
Category
Current Sense Amplifiers
Package
SOIC-8
Pins
8
In stock
5,871 at JLCPCB (C138706)
Used on
81 open-source boards

Overview

The INA219AID is a current Sense Amplifier made by Texas Instruments in a SOIC-8 package with 8 pins. -40℃~+125℃ 0.1uV/℃ 0V~26V 1 10uV 120dB 20nA 3V~5.5V 700uA Bidirectional detection、Zero drift / auto-zero、Input filter、Power monitoring、Digital output interface ±26V SOIC-8 Current Sense Amplifiers ROHS.

PCBKit's library has its KiCad symbol (Sensor_Energy:INA219AxD, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 5,871 are in stock at JLCPCB (part C138706). 81 open-source boards in 65 repositories on GitHub use it.

Symbol

1A12A03SDA4SCL5VS6GND7IN-8IN+
Sensor_Energy:INA219AxDFrom KiCad's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

14
Supply, least
3 V · VS, operating supply range, min · p. 6
Supply, most
5.5 V · VS, operating supply range, max · p. 6
Supply, absolute maximum
6 V · VS, absolute maximum · p. 4
Works from
-40 °C · Operating free-air temperature, min · p. 4
Works up to
125 °C · Operating free-air temperature, max · p. 4
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 4
Takes working
700 µA · VS quiescent current, typical · p. 6
Takes at most
1 mA · VS quiescent current, max · p. 6
Takes asleep
6 µA · VS quiescent current, power-down mode, typical · p. 6
A pin gives at most
10 mA · Open-drain digital output current, absolute maximum · p. 4
Junction to air (D (SOIC))
111.3 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (D (SOIC))
55.9 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (D (SOIC))
52 K/W · Junction-to-board thermal resistance · p. 4
Data rate, most
2.56 Mbit/s · High-speed I2C transmission, max · p. 17

What it is and has

7
Bus voltage sensing
0 to 26 V · p. 1
Measurements
Current, voltage, and power · p. 1
Programmable addresses
16 · p. 1
Filtering
Filtering options · p. 1
Calibration
Calibration registers · p. 1
Package options
SOT23-8 and SOIC-8 · p. 1
Interface
I2C and SMBus compatible · p. 13

Specifications

90
ParameterConditionsAs printedPage
Supply voltage VSOver operating free-air temperature rangemax 6 V4
Differential (VIN+ – VIN–)Analog Inputs; IN+, IN–min -26 · max 26 V4
Common-mode(VIN+ + VIN–) / 2IN+, IN–min -0.3 · max 26 V4
SDAMinimum: GND – 0.3 Vmax 6 V4
Input current into any pinmax 5 mA4
Open-drain digital output currentmax 10 mA4
Operating temperatureFree-airmin -40 · max 125 °C4
Junction temperature TJmax 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±4000 Vmax 4000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±750 Vmax 750 V4
Electrostatic discharge V(ESD)Machine Model (MM); ±200 Vmax 200 V4
VCM VCMNominal valuetyp 12 V4
VS VSNominal valuetyp 3.3 V4
TA TAOperating free-air temperaturemin -25 · max 85 ºC4
Junction-to-ambient thermal resistance RθJAD (SOIC), 8 PINStyp 111.3 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)D (SOIC), 8 PINStyp 55.9 °C/W4
Junction-to-board thermal resistance RθJBD (SOIC), 8 PINStyp 52 °C/W4
Junction-to-top characterization parameter ψJTD (SOIC), 8 PINStyp 10.7 °C/W4
Junction-to-board characterization parameter ψJBD (SOIC), 8 PINStyp 51.5 °C/W4
Full-scale current sense (input) voltage range VSHUNTINA219A; PGA = /1; maximum ±40 mVmin 0 · max 40 mV5
Full-scale current sense (input) voltage range VSHUNTINA219A; PGA = /2; maximum ±80 mVmin 0 · max 80 mV5
Full-scale current sense (input) voltage range VSHUNTINA219A; PGA = /4; maximum ±160 mVmin 0 · max 160 mV5
Full-scale current sense (input) voltage range VSHUNTINA219A; PGA = /8; maximum ±320 mVmin 0 · max 320 mV5
Bus voltage (input voltage) rangeINA219A; BRNG = 1; ADC scaling only, applied voltage must not exceed 26 Vmin 0 · max 32 V5
Bus voltage (input voltage) rangeINA219A; BRNG = 0min 0 · max 16 V5
Common-mode rejection CMRRINA219A; VIN+ = 0 to 26 Vmin 100 · typ 120 dB5
Offset voltage, RTI VOSINA219A; PGA = /1; typical ±10 uV, maximum ±100 uVtyp 10 · max 100 uV5
Offset voltage, RTI VOSINA219A; PGA = /2; typical ±20 uV, maximum ±125 uVtyp 20 · max 125 uV5
Offset voltage, RTI VOSINA219A; PGA = /4; typical ±30 uV, maximum ±150 uVtyp 30 · max 150 uV5
Offset voltage, RTI VOSINA219A; PGA = /8; typical ±40 uV, maximum ±200 uVtyp 40 · max 200 uV5
vs Temperature VOSINA219A; offset voltage; TA = –25°C to 85°Ctyp 0.1 uV/°C5
vs Power Supply PSRRINA219A; VS = 3 to 5.5 Vtyp 10 uV/V5
Current sense gain errorINA219A; typical ±40 m%typ 40 m%5
vs TemperatureINA219A; current sense gain error; TA = –25°C to 85°Ctyp 1 m%/°C5
IN+ pin input bias currentINA219A; Active modetyp 20 uA5
IN– pin input bias currentINA219A; Active modetyp 20 uA5
VIN– pin input impedanceINA219A; Active modetyp 320 kΩ5
IN+ pin input leakageINA219A; Power-down mode; maximum ±0.5 uAtyp 0.1 · max 0.5 uA5
IN– pin input leakageINA219A; Power-down mode; maximum ±0.5 uAtyp 0.1 · max 0.5 uA5
ADC basic resolutionINA219Atyp 12 bits5
Shunt voltage, 1 LSB step sizeINA219Atyp 10 uV5
Bus voltage, 1 LSB step sizeINA219Atyp 4 mV5
Current measurement errorINA219A; typical ±0.2%, maximum ±0.5%typ 0.2 · max 0.5 %5
over TemperatureINA219A; current measurement error; TA = –25°C to 85°C; maximum ±1%max 1 %5
Bus voltage measurement errorINA219A; typical ±0.2%, maximum ±0.5%typ 0.2 · max 0.5 %5
over TemperatureINA219A; bus voltage measurement error; TA = –25°C to 85°C; maximum ±1%max 1 %5
Differential nonlinearityINA219A; typical ±0.1 LSBtyp 0.1 LSB5
ADC conversion timeINA219A; 12 bittyp 532 · max 586 us5
ADC conversion timeINA219A; 11 bittyp 276 · max 304 us5
ADC conversion timeINA219A; 10 bittyp 148 · max 163 us5
ADC conversion timeINA219A; 9 bittyp 84 · max 93 us5
Minimum convert input low timeINA219Amin 4 us5
SMBus timeoutINA219Atyp 28 · max 35 ms5
Input capacitanceINA219A; SDA as Input, SCL, A0, A1typ 3 pF5
Leakage input currentINA219A; SDA as Input, SCL, A0, A1; 0 ≤ VIN ≤ VStyp 0.1 · max 1 uA5
VIH input logic level VIHINA219A; SDA as Input, SCL, A0, A1; minimum 0.7 (VS)max 6 V5
VIL input logic level VILINA219A; SDA as Input, SCL, A0, A1; maximum 0.3 (VS)min -0.3 V5
HysteresisINA219A; digital inputstyp 500 mV6
Logic 0 output levelINA219A; SDA; ISINK = 3 mAtyp 0.15 · max 0.4 V6
High-level output leakage currentINA219A; SDA; VOUT = VStyp 0.1 · max 1 uA6
Operating supply rangeINA219Amin 3 · max 5.5 V6
Quiescent currentINA219Atyp 0.7 · max 1 mA6
Quiescent current, power-down modeINA219Atyp 6 · max 15 uA6
Power-on reset thresholdINA219Atyp 2 V6
SCL operating frequency ƒ(SCL)FAST MODEmin 0.001 · max 0.4 MHz6
SCL operating frequency ƒ(SCL)HIGH-SPEED MODEmin 0.001 · max 2.56 MHz6
Bus free time between STOP and START condition t(BUF)FAST MODEmin 1300 ns6
Bus free time between STOP and START condition t(BUF)HIGH-SPEED MODEmin 160 ns6
Hold time after repeated START condition. After this period, the first clock is generated. t(HDSTA)FAST MODEmin 600 ns6
Hold time after repeated START condition. After this period, the first clock is generated. t(HDSTA)HIGH-SPEED MODEmin 160 ns6
Repeated START condition setup time t(SUSTA)FAST MODEmin 600 ns6
Repeated START condition setup time t(SUSTA)HIGH-SPEED MODEmin 160 ns6
STOP condition setup time t(SUSTO)FAST MODEmin 600 ns6
STOP condition setup time t(SUSTO)HIGH-SPEED MODEmin 160 ns6
Data hold time t(HDDAT)FAST MODEmin 0 · max 900 ns6
Data hold time t(HDDAT)HIGH-SPEED MODEmin 0 · max 90 ns6
Data setup time t(SUDAT)FAST MODEmin 100 ns6
Data setup time t(SUDAT)HIGH-SPEED MODEmin 10 ns6
SCL clock LOW period t(LOW)FAST MODEmin 1300 ns6
SCL clock LOW period t(LOW)HIGH-SPEED MODEmin 250 ns6
SCL clock HIGH period t(HIGH)FAST MODEmin 600 ns6
SCL clock HIGH period t(HIGH)HIGH-SPEED MODEmin 60 ns6
Data fall time tF DAFAST MODEmax 300 ns6
Data fall time tF DAHIGH-SPEED MODEmax 150 ns6
Clock fall time tFCLFAST MODEmax 300 ns6
Clock fall time tFCLHIGH-SPEED MODEmax 40 ns6
Clock rise time tRCLFAST MODEmax 300 ns6
Clock rise time tRCLHIGH-SPEED MODEmax 40 ns6
Clock rise time for SCLK ≤ 100kHz tRCLFAST MODEmax 1000 ns6

Pins, by the datasheet

8
1 A1
Address pin; Table 1 shows pin settings and corresponding addresses. · p. 3
2 A0
Address pin; Table 1 shows pin settings and corresponding addresses. · p. 3
3 SDA
Serial bus data line. · p. 3
4 SCL
Serial bus clock line. · p. 3
5 VS
Power supply, 3 to 5.5 V. · p. 3
6 GND
Ground. · p. 3
7 IN–
Negative differential shunt voltage; connect to negative side of shunt resistor. Bus voltage is measured from this pin to ground. · p. 3
8 IN+
Positive differential shunt voltage; connect to positive side of shunt resistor. · p. 3

Open-source boards using it

81See all 81
  • 4 layers82.6 × 82.5 mmJumperless2, the printed circuit board in 3D

    Jumperless2

    Architeuthis-Flux/Jumperless

    A jumperless breadboard

    208 parts914
  • 4 layers82.6 × 82.6 mmJumperlessV5r8, the printed circuit board in 3D

    JumperlessV5r8

    Architeuthis-Flux/JumperlessV5

    The next generation jumperless breadboard

    650 parts332
  • 2 layers74.4 × 51.2 mmEsp32-wroom timer, the printed circuit board in 3D

    Esp32-wroom timer

    AlessandroAU/Chorus32-ESP32LapTimer

    This is an ESP32 port of the popular Chorus RF Laptimer

    66 parts102GPL-3.0
  • 2 layers169.3 × 128 mmPSU PCB, the printed circuit board in 3D

    PSU PCB

    ThomasVDD/SmartSupply

    SmartSupply is a digital battery powered lab powersupply. It is Arduino compatible and can be controlled via PC over USB.

    134 parts96
  • 4 layers100 × 54 mmKbox, the printed circuit board in 3D

    Kbox

    sarfata/kbox-hardware

    Open-source electronics for your boat

    139 parts19
  • 2 layers50 × 100 mmPSU PCB, the printed circuit board in 3D

    PSU PCB

    ThomasVDD/SmartSupplyMini

    118 parts16
  • 2 layers101.6 × 53.3 mmBatteryAnalyzer MkII, the printed circuit board in 3D

    BatteryAnalyzer MkII

    Moragor/BatteryAnalyzer_MkII

    Updated Version of the battery analyzer, now with constant current

    25 parts12MIT
  • 2 layers100 × 100 mmWLEDController, the printed circuit board in 3D

    WLEDController

    LostInCompilation/WLED-Controller-PCB

    WLED Controller Board with ESP32 - 4 Channels - Current and Power Monitoring - INMP441 Microphone

    69 parts8

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the INA219AID?

Yes. The symbol is Sensor_Energy:INA219AxD and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the INA219AID?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the INA219AID datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the INA219AID?

JLCPCB lists it as part C138706, with 5,871 in stock; the sellers' links on this page open their listings.

What can replace the INA219AID?

Parts like it in the library: the INA240A1D by Texas Instruments, the CSA240LCSOIC8 by analogysemi, the MAX4080TASA+T by Maxim Integrated (Analog Devices) and the INA240A3D by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the INA219AID?

81 boards in 65 repositories on GitHub; the most starred are listed on this page, with their KiCad files.