Skip to the content
12345678

INA240A1D

Texas InstrumentsExtended

-40℃~+125℃ -4V~80V 1 1.8mA 132dB 2.7V~5.5V 20V/V 250nV/℃ 2V/us 400kHz 40nV/√Hz@1kHz 5uV 90uA Bidirectional detection、Zero drift / auto-zero、Programmable output reference level、Analog output interface ±80V SOIC-8 Current Sense Amplifiers ROHS

Part id
ti/INA240A1D
Category
Current Sense Amplifiers
Package
SOIC-8
Pins
8
In stock
2,585 at JLCPCB (C2060769)
Used on
36 open-source boards

Overview

The INA240A1D is a current Sense Amplifier made by Texas Instruments in a SOIC-8 package with 8 pins. -40℃~+125℃ -4V~80V 1 1.8mA 132dB 2.7V~5.5V 20V/V 250nV/℃ 2V/us 400kHz 40nV/√Hz@1kHz 5uV 90uA Bidirectional detection、Zero drift / auto-zero、Programmable output reference level、Analog output interface ±80V SOIC-8 Current Sense Amplifiers ROHS.

PCBKit's library has its KiCad symbol (Amplifier_Current:INA240A1D, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 2,585 are in stock at JLCPCB (part C2060769). 36 open-source boards in 33 repositories on GitHub use it.

Symbol

1-2GND3REF256V+7REF18+
Amplifier_Current:INA240A1DFrom KiCad's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

11
Supply, least
2.7 V · VS, recommended operating min · p. 4
Supply, most
5.5 V · VS, recommended operating max · p. 4
Supply, absolute maximum
6 V · VS, absolute max · p. 4
Works from
-40 °C · Operating free-air temperature min · p. 4
Works up to
125 °C · Operating free-air temperature max · p. 4
Junction, hottest
150 °C · Junction temperature absolute max · p. 4
Takes working
1.8 mA · VS quiescent current typical, VSENSE = 0 mV · p. 5
Takes at most
2.6 mA · VS quiescent current max, TA = –40°C to 125°C · p. 5
Junction to air (D (SOIC))
113.5 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (D (SOIC))
51.9 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (D (SOIC))
57.8 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

9
PWM rejection
Enhanced · p. 1
Common-mode range
–4 V to 80 V · p. 1
Gain
20 V/V · p. 1
DC CMRR
132 dB · p. 1
AC CMRR
93 dB at 50 kHz · p. 1
Gain error
0.20% maximum · p. 1
Gain drift
2.5 ppm/°C maximum · p. 1
Offset voltage
±25 μV maximum · p. 1
Offset drift
250 nV/°C maximum · p. 1

Around it

2
cap 0.1 μF
between VS and GND; Supply bypass capacitor; place as close as possible to the supply and ground pins. · p. 23
res 100-mΩ
between IN+ and IN–; Current-sensing shunt selected for the INA240A1 inline motor application. · p. 20

Specifications

40
ParameterConditionsAs printedPage
Supply voltageOver operating free-air temperature rangemax 6 V4
Analog inputs, VIN+, VIN–Differential (VIN+) – (VIN–)min -80 · max 80 V4
Analog inputs, VIN+, VIN–Common-modemin -6 · max 90 V4
Operating free-air temperature, TA TAmin -55 · max 150 °C4
Junction temperature, TJ TJmax 150 °C4
Storage temperature, Tstg Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1000 Vmax 1000 V4
Common-mode input voltage VCMOver operating free-air temperature rangemin -4 · max 80 V4
Operating supply voltage VSOver operating free-air temperature rangemin 2.7 · max 5.5 V4
Operating free-air temperature TAmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJAD (SOIC), 8 pinstyp 113.5 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)D (SOIC), 8 pinstyp 51.9 °C/W4
Junction-to-board thermal resistance RθJBD (SOIC), 8 pinstyp 57.8 °C/W4
Junction-to-top characterization parameter ψJTD (SOIC), 8 pinstyp 10.2 °C/W4
Junction-to-board characterization parameter ψJBD (SOIC), 8 pinstyp 56.9 °C/W4
Common-mode input range VCMVIN+ = –4 V to 80 V, VSENSE = 0 mV; TA = –40°C to 125°Cmin -4 · max 80 V5
Common-mode rejection ratio CMRRVIN+ = –4 V to 80 V, VSENSE = 0 mV; TA = –40°C to 125°Cmin 120 · typ 132 dB5
Common-mode rejection ratio CMRRf = 50 kHztyp 93 dB5
Offset voltage, input-referred VOSVSENSE = 0 mV; values are ±typ 5 · max 25 uV5
Offset voltage drift dVOS/dTVSENSE = 0 mV, TA = –40°C to 125°C; values are ±typ 50 · max 250 nV/°C5
Power-supply rejection ratio PSRRVS = 2.7 V to 5.5 V, VSENSE = 0 mV; TA = –40°C to 125°C; values are ±typ 1 · max 10 uV/V5
Input bias current IBIB+, IB–, VSENSE = 0 mVtyp 90 uA5
Reference input rangeUpper limit is VSmin 0 V5
Gain GINA240A1typ 20 V/V5
Gain errorGND + 50 mV ≤ VOUT ≤ VS – 200 mV; values are ±typ 0.05 · max 0.2 %5
Gain errorTA = –40°C to 125°C; values are ±typ 0.5 · max 2.5 ppm/°C5
Non-linearity errorGND + 10 mV ≤ VOUT ≤ VS – 200 mV; value is ±typ 0.01 %5
Reference divider accuracyVOUT = | (VREF1 – VREF2) | / 2 at VSENSE = 0 mV, TA = –40°C to 125°Ctyp 0.02 · max 0.1 %5
Reference voltage rejection ratio (input-referred) RVRRINA240A1typ 20 uV/V5
Maximum capacitive loadNo sustained oscillationtyp 1 nF5
Bandwidth BWAll gains, –3-dB bandwidthtyp 400 kHz5
Bandwidth BWAll gains, 2% THD+Ntyp 100 kHz5
Settling time - output settles to 0.5% of final valueINA240A1typ 9.6 us5
Slew rate SRtyp 2 V/us5
Voltage noise densityInput referredtyp 40 nV/√ Hz5
Operating voltage range VSTA = –40°C to 125°Cmin 2.7 · max 5.5 V5
Quiescent current IQVSENSE = 0 mVtyp 1.8 · max 2.4 mA5
Quiescent current IQIQ vs temperature, TA = –40°C to 125°Cmax 2.6 mA5
Specified rangemin -40 · max 125 °C5

Pins, by the datasheet

8
1 IN–
Connect to load side of shunt resistor. · p. 3
2 GND
Ground. · p. 3
3 REF2
Reference 2 voltage; connect to 0 V to VS to set the output midpoint. · p. 3
4 NC
Reserved. Connect to ground or leave floating. · p. 3
5 OUT
Output voltage. · p. 3
6 VS
Power supply, 2.7 V to 5.5 V. · p. 3
7 REF1
Reference 1 voltage; connect to 0 V to VS to set the output midpoint. · p. 3
8 IN+
Connect to supply side of shunt resistor. · p. 3

Open-source boards using it

36See all 36
  • 4 layers231 × 67 mmBESC G2, the printed circuit board in 3D

    BESC G2

    galpavlin/BESC-G2

    BESC second generation

    300 parts58
  • 6 layers76 × 46.4 mmRp2350 driver, the printed circuit board in 3D

    Rp2350 driver

    sequoia-hope/rp2350-motor-controller

    An RP2350 based brushless motor controller

    291 parts39
  • 4 layers55.5 × 0 mmGesc, the printed circuit board in 3D

    Gesc

    CTSchorsch/gesc

    DC Motor Controler based on Benjamin Vedders VESC

    159 parts17
  • 4 layers47 × 47 mmMotor Gen2, the printed circuit board in 3D

    Motor Gen2

    RoMeLaUCLA/romela-motor-driver

    Motor driver PCB and firmware designed for RoMeLa actuators.

    151 parts6MIT
  • 4 layers10 × 22.5 mmCircle, the printed circuit board in 3D

    Circle

    osrf/slow_bldc

    52 parts4Apache-2.0
  • 4 layers100.3 × 50.3 mmGreenmobi drive, the printed circuit board in 3D

    Greenmobi drive

    G-Pereira/greenmobi-drive

    A FOC motor drive compatible with VESC

    160 parts1CERN-OHL-S-2.0
  • 2 layers76 × 53 mmSepic, the printed circuit board in 3D

    Sepic

    aguscsc/Model-Predictive-Control-Strategies-for-Fourth-Order-Power-Converters

    This repository contains the design an implementation of a SEPIC (Single-Ended Primary-Inductor Converter) to test and compare the application of model predictive control on fourth-order power converters.

    27 parts
  • 4 layers230 × 152 mmSENTINEL TRM, the printed circuit board in 3D

    SENTINEL TRM

    ajisrawi/sentinel-uhf-radar

    Reference design of a two-face UHF early-warning phased-array radar: system sizing, MoM antenna simulation, seven KiCad PCB projects, Blender site model

    144 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the INA240A1D?

Yes. The symbol is Amplifier_Current:INA240A1D and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the INA240A1D?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the INA240A1D datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the INA240A1D?

JLCPCB lists it as part C2060769, with 2,585 in stock; the sellers' links on this page open their listings.

What can replace the INA240A1D?

Parts like it in the library: the INA219AID by Texas Instruments, the CSA240LCSOIC8 by analogysemi, the MAX4080TASA+T by Maxim Integrated (Analog Devices) and the INA240A3D by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the INA240A1D?

36 boards in 33 repositories on GitHub; the most starred are listed on this page, with their KiCad files.