
Controller
terjeio/PCBLaserMkII
Mechanical and electrical design files for revised version of my PCB Laser exposer

Mechanical and electrical design files for revised version of my PCB Laser exposer
Driver is an open-source printed circuit board by terjeio, from the terjeio/PCBLaserMkII repository on GitHub. It is a 2-layer board of 28 × 35 mm with 22 parts on 16 nets, routed with 159 tracks and 0 vias.
It is built around the LM358, 100UF/16V and BC847. Its parts include 10 resistors, 4 capacitors, 2 ICs, 2 transistors and 2 connectors.
160 x 100mm exposure area (Eurocard). Able to render at least down to 0.25mm (10 mil, 250um) track/track separation. Easy workflow.
Vector plotting requires parsing of a vector format to control the drive mechanism, most PCB-design packages are able to output the design in Gerber and/or HPGL-formats.
Raster plotting is similar to inkjet printing, the laser is fired for the individual pixels.
I decided to use raster plotting since this is relatively simple to implement.
By using the belt calculator available at buildlog.net I found that 17 teeth pulleys and 8 microsteps would result in a resolution of 1195.297 steps per inch, which is pretty close to 1200 dpi (21.250 um/step). Near enough for hobby use, resolution may be adjusted when generating the bitmap file to match the actual resolution if a perfect match is required.
I had some blank PCBs lying around so I wanted to try Dupont Riston dry-film photoresist. This has optimal sensitivity in the 350-380nm range, and may be exposed by 405nm as there is some sensitivity up to 450nm. Lines and spaces achievable: In optimized production environment: 75um/3mil In lab environment: 50um/2mil
The (teoretical) resolution of the design is thus somewhat better than the resolution of the film.
Plot the design to PDF in 1:1 format. Print resulting files via PDFCreator to PNG-format files, I use 4bpp in order to avoid artefacts in the bitmap.
Firmware is provided for MSP430G2553 LaunchPad or MSP430F5310 on a custom PCB. The MSP430F5310 is slightly faster and has more RAM, useful for buffering. It also supports adjusting the laser power via the desktop application.
Firmware may be compiled in the cloud, there is no need to install a local IDE.
A closed design with an interlocked door to block reflections from the laser. The published version is an open design, ALWAYS use protective eyewear when operating the exposer!
Laser cut acrylic bed? My prototype has an aluminium bed that requires access to a mill to fabricate.
BOM:
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10K | Resistors_SMD:R_0805 | R4, R5 |
| 2 | 39K | Resistors_SMD:R_0805 | R1, R2 |
| 2 | 8R2 | Resistors_SMD:R_1206 | R7, R8 |
| 1 | 0R | Resistors_SMD:R_0805 | R3 |
| 1 | 100nF | Capacitors_SMD:C_0805 | C3 |
| 1 | 100nF | Capacitors_SMD:C_1206 | C1 |
| 1 | 100uF/16V | Capacitors_SMD:CP_Elec_5x4.5 | C6 |
| 1 | 1K8 | Resistors_SMD:R_0805 | R9 |
| 1 | 1nF | Capacitors_SMD:C_1206 | C7 |
| 1 | 2N7002 | TO_SOT_Packages_SMD:SOT-23 | Q1 |
| 1 | 4K7 | Resistors_SMD:R_0805 | R10 |
| 1 | 5K | Potentiometers:Potentiometer_Trimmer_Bourns_3296P | RV1 |
| 1 | BC847 | TO_SOT_Packages_SMD:SOT-23 | Q2 |
| 1 | CONN_01X14 | IoEngineering:MOLEX_52271-1279 | P1 |
| 1 | Controller | Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mm | J1 |
| 1 | LM358 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U2 |
| 1 | MCP4725 | TO_SOT_Packages_SMD:SOT-23-6 | U1 |
| 1 | R | Resistors_SMD:R_0805 | R6 |
| 1 | SLD3235VF | IoEngineering:TO-18-3_Laser_brass_host | LD1 |

terjeio/PCBLaserMkII
Mechanical and electrical design files for revised version of my PCB Laser exposer



jaeyeon302/2021BEV
Graduation Project making Battery Electric Vehicle. Dept. of Electrical and Computer Engineering at SNU.





simonyiszk/ARDF-80m-rx
Rókavevő a 80m-es rádióamatőr sávra (3579 kHz fix frekvenciájú)
It measures 28 × 35 mm and has 2 copper layers, 1.6 mm thick.
22 parts, built around the LM358, 100UF/16V and BC847. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the terjeio/PCBLaserMkII repository on GitHub, at the commit this page was made from: the board is Electrical/Driver/Driver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask terjeio before reusing the design.