

Cardradio
The 1986 Casio RD-10 was an 86 × 54 × 2.2 mm card with a Philips TDA7020T, a CR2016 cell and a proprietary flat earphone plug. The earphone lead was also the antenna and the power switch.
- Size
- 83.2 × 51.6 mm
- Copper layers
- 2
- Thickness
- 0.4 mm
- Parts
- 44
- Nets
- 30
- Pads
- 151
- Tracks, vias
- 229, 280
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 3 Oct 2026
- Updated
- 3 Oct 2026
Overview
Cardradio is an open-source printed circuit board by tend876, from the tend876/Card-Radio-1 repository on GitHub. It is a 2-layer board of 83.2 × 51.6 mm with 44 parts on 30 nets, routed with 229 tracks and 280 vias.
It is built around the CH32V003F4P6, RDA5807M and XC6206P302MR, with the SJ-3524-SMT-TR among its other parts. Its parts include 13 capacitors, 12 resistors, 4 ICs, 4 switches and 3 connectors. It belongs with the RISC-V boards of this library.
Main components
4CH32V003F4P6
TSSOP-20-175milTSSOP-20-175mil Microcontrollers (MCU/MPU/SOC) ROHSWCH (Nanjing Qinheng Microelectronics)Microcontrollers (MCU/MPU/SOC)RDA5807M
MSOP-10MSOP-10 RF Transceiver ICs ROHSRDA MicroelectronicsRF Transceiver ICsXC6206P302MR
SOT-23-40℃~+85℃ 1 240mV@(50mA) 300mA 3V 3uA 40dB@(1kHz) 8V Fixed Over Current Protection、Short Circuit Protection Positive SOT-23 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSHXY MOSFETVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSJ-3524-SMT-TR
SMDSMD Audio Connectors ROHSCUIAudio Connectors (Headphones)
README
README.mdCR-1: a credit-card FM receiver (after the Casio RD-10)
The 1986 Casio RD-10 was an 86 × 54 × 2.2 mm card with a Philips TDA7020T, a CR2016 cell and a proprietary flat earphone plug. The earphone lead was also the antenna and the power switch. CR-1 keeps that behaviour but uses modern parts:
| RD-10 (1986) | CR-1 (this design) | |
|---|---|---|
| Outline | ≈86 × 54 mm | 85.60 × 53.98 mm, R3.18 (ISO/IEC 7810 ID-1, exactly) |
| Thickness | 2.2 mm | 6.5 mm closed (or 6.0 mm with the jack top showing through a lid window) |
| Earphone | Proprietary flat plug | Standard 3.5 mm TRS jack (airline giveaway earbuds, phone earbuds) |
| Tuner | TDA7020T (FLL, mono) | RDA5807M (stereo, seek, I²C) |
| Antenna | Earphone lead | Earphone lead (sleeve isolated from ground by FB3 at RF) |
| Power switch | Plug in | Plug in (J1 tip-switch → MCU wake from ~10 µA standby) |
| Battery | CR2016 | ~450 mAh LiPo (303450), USB-C charging, roughly 18 h of play |
| Controls | — | VOL+ / VOL− / SEEK◀ / SEEK▶ (hold SEEK▶ = bass, hold SEEK◀ = mono) |
Why it's 6.5 mm thick and not 5 mm
The thickness is set by the jack. A standard 3.5 mm jack body is 5.0 mm tall (CUI SJ-3524-SMT: 17 × 6 × 5 mm), and the stack through the jack is:
0.5 floor + 0.4 PCB + 5.0 jack + 0.1 clearance + 0.5 lid skin = 6.5 mm.
housing.py --thin makes a 6.0 mm version in which the top of the jack sits 0.1 mm below a window in the lid. Getting below that would need a mid-mount (board-cutout) jack. I left that out because I couldn't verify a mid-mount part's footprint drawing.
Repository layout
kicad/ KiCad project (made with KiCad 7, opens in 8/9): cardradio.kicad_pro/.kicad_sch/.kicad_pcb
+ project libs (cardradio.kicad_sym, cardradio.pretty), drc_report.txt
fab/ Gerbers + Excellon drill (gerbers/), BOM (cardradio-bom.csv), pick-and-place (cardradio-pos.csv)
cad/ housing.py (CadQuery, parametric), render.py, drawing.py
cad/out/ tray / lid / button-cap STEP + STL for both variants, full assembly STEP (with PCB and
component envelopes), housing_drawing.pdf, renders
firmware/ bare-metal C for the CH32V003 (Makefile, builds to ~2.5 KB)
docs/ schematic PDF, PCB top PDF
tools/ the generators: design.py is the single source of truth (parts, nets, placement);
gen_sch.py, gen_pcb.py, route_board.py (+ router.py), check_pcb.py, verify_netlist.py,
export_envelopes.py, make_bom.pyElectronics
- U1 RDA5807M (MSOP-10) with a 32.768 kHz crystal on RCLK, wired as on the common RRD-102 module. LOUT and ROUT drive the earbuds directly through 100 µF couplers (C10, C11) and ferrite beads (FB1, FB2).
- Antenna: the earphone sleeve (ANT) goes to GND through FB3 (1.5 kΩ at 100 MHz). At audio frequencies the sleeve is ground; at FM frequencies the whole cable floats and becomes the antenna, which feeds FMIN through C12 (22 pF) with L1 (100 nH) as the shunt. C13 and C9 are DNP positions for tuning the match and the crystal.
- Plug = power: with no plug in, J1's tip switch (TN) closes to the tip spring, which holds PLUG_DET low through R10, FB1 and R12. Inserting a plug opens TN, R9 (1 MΩ) pulls PLUG_DET high, and EXTI line 2 wakes the MCU from standby. Standby draw is about 3 µA in R9 plus the MCU and LDO quiescent current.
- U2 CH32V003F4P6 handles the buttons (PC3–PC6), bit-banged I²C (PC1/PC2), the status LED (PD0) and VBAT/2 sensing (PD4/A7). It is programmed over SWIO from the J3 pogo pads (3V0 / IO / G) with a WCH-LinkE.
- Power: USB-C (CC pull-downs 5.1 kΩ, charge only) → U4 MCP73831 at about 213 mA (R4 = 4.7 kΩ) → LiPo → U3 XC6206 3.0 V LDO. D1 shows charging.
PCB: 2 layers, 0.4 mm, 83.2 × 51.6 mm with notches for the four screw bosses. All components are on the top side and the LiPo is taped on top of the board. JLCPCB-class rules: 0.15/0.15 mm track/space, 0.3/0.6 mm vias, GND pours on both layers, about 220 stitching vias.
Verification run on the generated files:
- Schematic netlist (exported with
kicad-cli) matchesdesign.py: 30 nets OK. - PCB pad nets match. Every footprint is linked to its schematic symbol.
- KiCad DRC: 0 unconnected items, 0 clearance errors, 0 courtyard overlaps. It reports 5 starved-thermal warnings, on GND pads that each also have a dedicated via stub.
- Housing fit check (
housing.py): no interference between the tray, lid, caps and any component envelope, PCB or battery. The battery has 1.7 mm headroom for a 1.5 mm foam pad.
I hand-generated the board and routed it with a small custom 45° A* router (tools/router.py). Before you order, open it in KiCad, run DRC with your fab's rule set and look over the routing. You may want to re-route the RF/audio corner by hand.
Housing (CNC)
- Tray: 6061-T6. A single pocket leaves a 0.5 mm floor and 1.0 mm walls. Four corner bosses are tapped M1.4. There is a Ø5.2 jack-nose notch and a 9.3 × 3.6 USB-C slot on the right-hand short edge. The back is engraved.
- Lid: a 0.8 mm skin with a 0.3 mm recess over the jack, 4 × Ø3.3 button holes, 2 × Ø1.2 LED holes, 4 countersinks and five Ø2.4 posts that clamp the PCB. The face is engraved with the legends and RD-10-style pinstripes.
- Caps: 4 top-hat buttons (POM or aluminium), captive under the lid, standing 0.3 mm proud.
- Anodise both parts. The anodise keeps the jack sleeve (the antenna) insulated from the case. Send the STEP files to the CNC service;
housing_drawing.pdfcovers the critical dimensions and the notes.
Mechanical BOM: 4 × M1.4 × 4 flat-head screws (laptop type, head ≤ 0.8 mm), 2 × Ø1.0 mm PMMA light pipes about 4.7 mm long, a 1.5 mm PORON pad about 34 × 50 mm, 0.1 mm double-sided tape, and an LP303450 LiPo with a protection PCM.
Firmware
cd firmware && make (needs riscv64-unknown-elf-gcc), then make flash with minichlink and a WCH-LinkE on J3. The firmware uses no vendor SDK. Its state (station, volume, bass, mono) lives in a .noinit RAM section, so it survives standby. It shuts down at VBAT < 3.2 V and double-blips the LED below 3.45 V. De-emphasis is 75 µs (Americas). For NZ, Europe or Asia, set bit 11 in r4 to get 50 µs.
Bring-up risks / things to check
- RCLK crystal: I copied the single-pin crystal hookup (RCLK to GND) from the RRD-102 module. If the RDA5807 won't lock, fit a 32.768 kHz CMOS oscillator output into the Y1 position (pad 1) and set
RCLK_DIRECT_INPUT(reg 02h bit 10). - Plug-detect polarity assumes the SJ-3524 tip switch is normally closed, which is the usual convention. If yours is normally open, invert
plug_in(). - FM matching (C12, L1, C13) is a starting point. Tune it on a real earbud cable.
- In-flight use: many airlines restrict FM receivers in flight because their local oscillator radiates. Check with the crew. Reception inside a metal fuselage is also poor, so expect it to work best at the gate and in the terminal.
Parts
44| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 4k7 | Resistor_SMD:R_0402_1005Metric | R4, R7, R8, R10 |
| 3 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5, C6, C7 |
| 3 | 1M | Resistor_SMD:R_0402_1005Metric | R5, R6, R9 |
| 2 | 100uF | Capacitor_SMD:C_1206_3216Metric | C10, C11 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R11 |
| 2 | 1k8@100MHz | Inductor_SMD:L_0402_1005Metric | FB1, FB2 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | DNP | Capacitor_SMD:C_0402_1005Metric | C9, C13 |
| 1 | 100nH | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 1k5@100MHz | Inductor_SMD:L_0603_1608Metric | FB3 |
| 1 | 22pF | Capacitor_SMD:C_0402_1005Metric | C12 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | CH32V003F4P6 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | LiPo 3.7V | cardradio:LiPo_Pads_2x | BT1 |
| 1 | MCP73831-2 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | RDA5807M | Package_SO:MSOP-10_3x3mm_P0.5mm | U1 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | SEEK< | Button_Switch_SMD:SW_SPST_PTS810 | SW3 |
| 1 | SEEK> | Button_Switch_SMD:SW_SPST_PTS810 | SW4 |
| 1 | SJ-3524-SMT | Connector_Audio:Jack_3.5mm_CUI_SJ-3524-SMT_Horizontal | J1 |
| 1 | SWIO | cardradio:ProgPads_1x03_P2.54mm | J3 |
| 1 | USB-C | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | VOL+ | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | VOL- | Button_Switch_SMD:SW_SPST_PTS810 | SW2 |
| 1 | XC6206P302MR | Package_TO_SOT_SMD:SOT-23 | U3 |
Similar boards
- 2 layers112.6 × 85.4 mm

- 2 layers72.8 × 32 mm

- 2 layers

- 2 layers85 × 117 mm

FM radio esp32 hardware
kanta/GARAGE-SAILING
KiCad 6.0 project files for the top and the bottom panel.
47 parts1MIT - 4 layers100 × 69.4 mm

FMTransceiver
Longing-Ingernot/FMTransceiver
This is an FM radio transmitter and receiver, all in one, built around an ESP32-S3, a KT0803L
71 parts1MIT - 2 layers56 × 52 mm

299Clock
Benjamin324/Alarm-Clock-Radio-ECE-299-
Micropython and Html establishing alarm clock and radio functionality on a rasperry pi pico w.
26 parts - 2 layers47.4 × 28.3 mm

05 a radio
ItzzInfinity/FM-Radio-Using-ESP-12E-and-RDA5807M
An FM radio receiver built using an ESP12E, interfaced with the RDA5807M module. Powered by a Li-Ion battery with a TP4056 charging module, amplified by a PAM8403, and output through a 10-watt speaker.
15 partsMIT - 2 layers86.4 × 50.8 mm

Mega328 FM
mit41301/RDA5807M-arduino-nano-clone-FM-radio
RDA5807M (+ arduino nano clone) FM radio with NEC IR remote control
38 parts
Questions
How big is the Cardradio PCB?
It measures 83.2 × 51.6 mm and has 2 copper layers, 0.4 mm thick.
What parts does the Cardradio use?
44 parts, built around the CH32V003F4P6, RDA5807M, XC6206P302MR and SJ-3524-SMT-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Cardradio KiCad files?
From the tend876/Card-Radio-1 repository on GitHub, at the commit this page was made from: the board is kicad/cardradio.kicad_pcb and its schematic kicad/cardradio.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Cardradio design in my own project?
Its repository states no licence, so its author keeps all rights: ask tend876 before reusing the design.