

DroneBrushlessESC
PCB schematic and design for Drone Project
- Size
- 30 × 70 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 98
- Nets
- 86
- Pads
- 361
- Tracks, vias
- 731, 154
- Pours
- 16
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 28 Jan 2026
- Updated
- 24 Feb 2026
Overview
DroneBrushlessESC is an open-source printed circuit board by TanvKT, from the TanvKT/DroneProjectHardware repository on GitHub, published under the MIT licence. It is a 4-layer board of 30 × 70 mm with 98 parts on 86 nets, routed with 731 tracks and 154 vias.
It is built around the STM32G070KBT6, M24C02-WMN6TP and SN74LVC1G11DCKR(AT), with the CSD17577Q5A and CSS2H-2512K-2L00J among its other parts. Its parts include 36 resistors, 25 capacitors, 6 ICs, 6 transistors and 4 connectors. It belongs with the STM32 boards of this library.
Main components
5STM32G070KBT6
LQFP-32(7x7)-40℃~+85℃ 128KB 12bit 29 2V~3.6V 32 Bit 36KB 64MHz ARM Cortex-M0+ Built-in+External FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)M24C02-WMN6TP
SOIC-8-40℃~+85℃ 2.5V~5.5V 200 Years 2Kbit 4,000,000 Cycles 400kHz 5ms I2C SOIC-8 EEPROM ROHSSTMicroelectronicsEEPROMSN74LVC1G11DCKR(AT)
SC-70-6-40℃~+125℃ 1 1.2V、1.9V、2.3V、2.4V、3.8V 1.65V~5.5V 1.7V、2V 3 3.7ns@5V,50pF 300mV、400mV、450mV、550mV 700mV、800mV 74LVC AND Gate SC-70-6 Logic Gates ROHSAOTELogic GatesCSD17577Q5A
SON-8(5x6)-55℃~+150℃ 1 N-channel 1.4V 102pF 13nC@4.5V 2.31nF 270pF 30V 4.8mΩ@4.5V 53W 60A N-Channel SON-8(5x6) MOSFETs ROHSTexas InstrumentsMOSFETsCSS2H-2512K-2L00J
2512-55℃~+170℃ 2mΩ 3W ±5% ±75ppm/℃ 2512 Chip Resistor - Surface Mount ROHSBournsChip Resistor - Surface Mount
README
README.mdDroneProjectHardware
PCB schematic and design for Drone Project
Parts
98| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 10K | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R5, R6, R9, R10, R11, R26, R27, R28, R29, R36 |
| 13 | 33 | Resistor_SMD:R_0402_1005Metric | R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R24, R30 |
| 7 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C3, C5, C9, C10, C14, C22, C25 |
| 6 | 1uF | Capacitor_SMD:C_0603_1608Metric | C18, C19, C20, C21, C23, C24 |
| 6 | CSD17577Q5A | Package_TO_SOT_SMD:TDSON-8-1 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 6 | NetTie_2 | NetTie:NetTie-2_SMD_Pad0.5mm | NT1, NT2, NT3, NT4, NT5, NT6 |
| 2 | 100 | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | 10uF | Capacitor_SMD:C_1206_3216Metric | C8, C13 |
| 2 | 1nf | Capacitor_SMD:C_0402_1005Metric | C6, C7 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C12, C15 |
| 2 | 22uF | Capacitor_SMD:C_0603_1608Metric | C2, C4 |
| 2 | 330 | Resistor_SMD:R_0402_1005Metric | R33, R34 |
| 2 | 4.7K | Resistor_SMD:R_0402_1005Metric | R23, R25 |
| 2 | CSS2H-2512K-2L00J | Resistor_SMD:R_2512_6332Metric | R31, R32 |
| 2 | INA180A2 | Package_TO_SOT_SMD:SOT-23-5 | U5, U6 |
| 1 | 100uF | Library:CAP_A768EB_6.8x6.8_KEM | C1 |
| 1 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 440uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C17 |
| 1 | 47K | Resistor_SMD:R_0402_1005Metric | R35 |
| 1 | 47nF | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | C0_SPI1_MISO | Library:Testpoint 1.6mm x 0.8mm | TP6 |
| 1 | C0_SPI1_MOSI | Library:Testpoint 1.6mm x 0.8mm | TP2 |
| 1 | C0_SPI1_SCK | Library:Testpoint 1.6mm x 0.8mm | TP9 |
| 1 | DRV8320SRTVR | Library:DRV8320SRTVR | U4 |
| 1 | Debug | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J3 |
| 1 | FAULT_OUT | Library:Testpoint 1.6mm x 0.8mm | TP8 |
| 1 | FerriteBead | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | GND | Library:Testpoint 1.6mm x 0.8mm | TP1 |
| 1 | I2C1_SCL | Library:Testpoint 1.6mm x 0.8mm | TP7 |
| 1 | I2C1_SDA | Library:Testpoint 1.6mm x 0.8mm | TP4 |
| 1 | LED BLUE | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | LED GREEN | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | LED RED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | M24C02-WMN6TP | Library:SOIC127P600X175-8N | U2 |
| 1 | MTR_CSN | Library:Testpoint 1.6mm x 0.8mm | TP10 |
| 1 | POS3P3 | Library:Testpoint 1.6mm x 0.8mm | TP5 |
| 1 | PTS815 SJM 250 SMTR LFS | Library:SW4_PTS815 SJM 250 SMTR LFS_CNK | SW1 |
| 1 | PWM_IN | Library:Testpoint 1.6mm x 0.8mm | TP3 |
| 1 | SN74LVC1G11DCKR | Library:SOT65P210X110-6N | U1 |
| 1 | STM32G070KBT6 | Library:QFP80P900X900X160-32N | U3 |
| 1 | Screw_Terminal_01x03 | Library:CUI_TB005_-762-03BE | J2 |
| 1 | UART | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J1 |
| 1 | ~ | Library:BrushlessESC | J4 |
More from TanvKT/DroneProjectHardware
2- 4 layers80 × 100 mm

- 4 layers75 × 50 mm

Similar boards
- 10 layers177.8 × 141 mm

- 2 layers90 × 30.3 mm

Integrated25
juicebox6030/Nova-Link
NOVA-LINK is an open, low-latency wireless communication protocol and firmware stack designed for use in real-time live event environments.
178 partsGPL-3.0 - 4 layers130 × 95 mm

Ax7010 servo reva
magic-alt/fpga-servo
This directory preserves the ADS8588S legacy PCB, native project and custom rules from b0172a2f65902c7281cf4a8454f192dc791a9ef9.
183 parts - 2 layers88.9 × 50.8 mm

Core16 LB
ageppert/Core16-Interactive-Core-Memory
Weave 16 bits of core memory and LEDs to interact with using a magnetic wand
130 parts5 - 4 layers100 × 80 mm

- 2 layers220 × 150 mm

- 4 layers200 × 150 mm

- 2 layers85 × 170 mm

Core64 LB
ageppert/Core-64-Interactive-Core-Memory-Badge
64 bits of core memory and LEDs to interact with directly using a magnetic wand.
194 parts17GPL-3.0
Questions
How big is the DroneBrushlessESC PCB?
It measures 30 × 70 mm and has 4 copper layers, 1.6 mm thick.
What parts does the DroneBrushlessESC use?
98 parts, built around the STM32G070KBT6, M24C02-WMN6TP, SN74LVC1G11DCKR(AT) and CSD17577Q5A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DroneBrushlessESC KiCad files?
From the TanvKT/DroneProjectHardware repository on GitHub, at the commit this page was made from: the board is DroneBrushlessESC/DroneBrushlessESC.kicad_pcb and its schematic Controller/Connectors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DroneBrushlessESC design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).