

Fall DETECTION
PCB
- Size
- 43.1 × 33.7 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 66
- Nets
- 73
- Pads
- 253
- Tracks, vias
- 446, 91
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 7 May 2025
- Updated
- 7 May 2025
Overview
Fall DETECTION is an open-source printed circuit board by SzymonZee, from the SzymonZee/PCB repository on GitHub. It is a 6-layer board of 43.1 × 33.7 mm with 66 parts on 73 nets, routed with 446 tracks and 91 vias.
It is built around the STM32WB55CCU6, DLF162500LT-5028A1 and ICM-20948, with the MCP1802T-3302I/OT, USBLC6-2SC6 and IRLML5203 among its other parts. Its parts include 25 capacitors, 10 resistors, 6 ICs, 3 connectors and 3 inductors. It belongs with the STM32 boards of this library.
Main components
6STM32WB55CCU6
UFQFPN-48-EP(7x7)UFQFPN-48-EP(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)DLF162500LT-5028A1
SMD-4P,1.6x0.8mm-40℃~+85℃ 0.33dB 2.4GHz~2.5GHz 49.2dB 50Ω Low Pass SMD-4P,1.6x0.8mm RF Filters ROHSTDKRF FiltersICM-20948
QFN-24(3x3)-40℃~+85℃ 0.5KB 1.71V~3.6V 16bit 8uA Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24(3x3) Accelerometers ROHSTDK InvenSenseAccelerometersMCP1802T-3302I/OT
SOT-23-5-40℃~+85℃@(Ta) 1 10V 25uA 3.3V 300mA 70dB@(10kHz) Fixed Over Current Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)IRLML5203
SOT-231 P-Channel 1.25W 165mΩ@4.5V 2.5V 30V 3A 43pF 510pF 71pF 9.5nC@0V P-Channel ±20V SOT-23 MOSFETs ROHSKUUMOSFETs
Parts
66| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 0.1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C3, C6, C8, C9, C11, C12, C13, C14, C16, C17, C18, C19, C23 |
| 9 | TestPoint | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9 |
| 4 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C20, C21, C22 |
| 2 | 4,7k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R20, R23 |
| 2 | 4.7k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6 |
| 2 | 4.7uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C15 |
| 2 | 4.7uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C30, C39 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7, R10 |
| 2 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H4 |
| 1 | 0.3pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 0.3pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C7 |
| 1 | 0.8pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5 |
| 1 | 0.8pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10 |
| 1 | 10nH | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | L1 |
| 1 | 10uH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L3 |
| 1 | 2.7nH | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | L2 |
| 1 | 200 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R11 |
| 1 | 32Mhz | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 1 | 32kHz768 | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm | Y2 |
| 1 | 4,7k | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | R22 |
| 1 | 5.1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2 |
| 1 | Antenna | ALL_FOOTRPINTS:ANTC3216X140N | AE1 |
| 1 | Conn_01x02_Pin | Connector_JST:JST_SH_BM02B-SRSS-TB_1x02-1MP_P1.00mm_Vertical | J3 |
| 1 | Conn_01x06_Pin | Connector_PinSocket_1.27mm:PinSocket_2x03_P1.27mm_Vertical_SMD | J12 |
| 1 | D | Diode_SMD:D_SOD-323 | D2 |
| 1 | DLF162500LT-5028A1 | ALL_FOOTRPINTS:DLF-4_1P6X0P8 | FL1 |
| 1 | ICM-20948 | Sensor_Motion:InvenSense_QFN-24_3x3mm_P0.4mm | U2 |
| 1 | IRLML5203 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | MCP1700x-180xxTT | Package_TO_SOT_SMD:SOT-23 | U5 |
| 1 | MCP1802T-3302I/OT | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | MCP73833-xxx-UN | Package_SO:MSOP-10_3x3mm_P0.5mm | U9 |
| 1 | R | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R21 |
| 1 | RS-282G05A3-SM RT | ALL_FOOTRPINTS:RS-282G05A3-SM RT_CNK-M | SW1 |
| 1 | STM32WB55CCU6 | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | Thermistor | Resistor_SMD:R_0603_1608Metric | TH1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J4 |
More from SzymonZee/PCB
3- 6 layers166 × 70.7 mm

- 6 layers38.3 × 34.6 mm

- 4 layers44.7 × 35.9 mm

Similar boards
- 4 layers

- 6 layers51.7 × 27.8 mm

STM32-Pill
HasanTheSyrian/stm32-bluetooth-pill
STM32 Black-pill inspired development board that supports Bluetooth
51 parts1 - 4 layers63.9 × 37.1 mm

Usbhid daq
shraken/usbhid_buddy
Hardware, firmware, and software for the USBHID DAQ 'Buddy' device
73 parts2 - 2 layers66 × 58.4 mm

- 4 layers50 × 50 mm

Watch wearable
TENNLab-UTK/NWRIST
Code and KiCAD PCB design for the NWRIST: Neuromorphic Wearable for Real-Time Intelligent Sensing Technology paper
79 parts - 2 layers17.7 × 17.7 mm

Stm32-module
YC-Lammy/STM32WB55CCU6_on_PLCC
STM32WB55CCU6 on a PLCC board for development use. a chip antenna and MPU-6050 on board.
73 parts1GPL-3.0 - 2 layers58 × 34.5 mm

- 4 layers70 × 99.9 mm

Micromouse
UBIEEE/FrankenMouse
FrankenMouse is a MicroMouse robot that was designed, built, and programmed from scratch by members of the University at Buffalo's IEEE Student Branch.
100 parts6MIT
Questions
How big is the Fall DETECTION PCB?
It measures 43.1 × 33.7 mm and has 6 copper layers, 1.6 mm thick.
What parts does the Fall DETECTION use?
66 parts, built around the STM32WB55CCU6, DLF162500LT-5028A1, ICM-20948 and MCP1802T-3302I/OT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Fall DETECTION KiCad files?
From the SzymonZee/PCB repository on GitHub, at the commit this page was made from: the board is Fall_DETECTION.kicad_pcb and its schematic Fall_DETECTION.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Fall DETECTION design in my own project?
Its repository states no licence, so its author keeps all rights: ask SzymonZee before reusing the design.