

STM32-Pill
STM32 Black-pill inspired development board that supports Bluetooth
- Size
- 51.7 × 27.8 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 51
- Nets
- 57
- Pads
- 199
- Tracks, vias
- 498, 60
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 23 Feb 2025
- Updated
- 13 Apr 2026
Overview
STM32-Pill is an open-source printed circuit board by HasanTheSyrian, from the HasanTheSyrian/stm32-bluetooth-pill repository on GitHub. It is a 6-layer board of 51.7 × 27.8 mm with 51 parts on 57 nets, routed with 498 tracks and 60 vias.
It is built around the STM32WB55CCU6, 2450LP14A100T and TPS73633DBV, with the USBLC6-2SC6 among its other parts. Its parts include 21 capacitors, 9 resistors, 4 connectors, 3 ICs and 3 inductors. It belongs with the STM32 boards of this library.
Main components
4STM32WB55CCU6
UFQFPN-48-EP(7x7)UFQFPN-48-EP(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)2450LP14A100T
SMD-6P,0.8x1.6mm0.5dB Low Pass SMD-6P,0.8x1.6mm RF Filters ROHSJohanson DielectricsRF FiltersTPS73633DBV
SOT-23-5-40℃~+125℃@(Tj) 1 3.3V 30uVrms 400mA 5.5V 550uA 58dB@(10kHz) 75mV@(400mA) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Reverse-polarity current protection、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
README
README.mdSTM32 Bluetooth Development Board
*Assembled and tested to be working except for the RF circuit which is likely a hardware issue but could be a software issue on my end. *There is a non-public version that uses a chip antenna. *I recommend removing the series resistor on the LDO input.
Parts
51| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100 nF | Capacitor_SMD:C_0805_2012Metric | C2, C3, C5, C6, C7, C8, C9, C10, C17 |
| 8 | 4.7 uF | Capacitor_SMD:C_0805_2012Metric | C1, C4, C11, C12, C18, C19, C20, C21 |
| 5 | LOGO | LOGO | G***, G***, G***, G***, G*** |
| 4 | 5.1K | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R5 |
| 2 | 10 pF | Capacitor_SMD:C_0805_2012Metric | C13, C14 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric | R7, R9 |
| 2 | 220R | Resistor_SMD:R_0805_2012Metric | R6, R8 |
| 2 | Conn_01x14 | Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_Vertical | J2, J3 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | BOOT0, SW1 |
| 1 | 0.3 pF | Capacitor_SMD:C_0201_0603Metric_Pad0.64x0.40mm_HandSolder | C16 |
| 1 | 0.8 pF | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 10 nH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 10 uH | Inductor_SMD:L_0805_2012Metric | L2 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | 2.7 nH | Inductor_SMD:L_0402_1005Metric | L3 |
| 1 | 2450LP14A100T | proj:ICCAF50P160X80X70-6N | FL1 |
| 1 | 32 MHz | Crystal:Crystal_SMD_SeikoEpson_FA128-4Pin_2.0x1.6mm | X1 |
| 1 | 32.768 kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | X2 |
| 1 | Conn_Coaxial | Connector_Coaxial:U.FL_Hirose_U.FL-R-SMT-1_Vertical | J4 |
| 1 | RED | Diode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | STM32WB55CCU6 | Package_QFP:STM32WB-QFN50P700X700X60-49N | U1 |
| 1 | TPS73633DBV | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U2 |
| 1 | USBLC6-2SC6 | proj:SOT95P280X145-6N | U3 |
| 1 | USB_C_2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
Similar boards
- 2 layers85.8 × 53.4 mm

- 4 layers

- 6 layers166 × 70.7 mm

- 2 layers17.7 × 17.7 mm

Stm32-module
YC-Lammy/STM32WB55CCU6_on_PLCC
STM32WB55CCU6 on a PLCC board for development use. a chip antenna and MPU-6050 on board.
73 parts1GPL-3.0 - 4 layers132.5 × 82 mm

Wandfernsprecher
hanebefl/wandfernsprecher-hw
GSM conversion for a old German Wandfernsprecher telephone
93 parts6 - 4 layers35.6 × 35.6 mm

- 2 layers100 × 74 mm

- 2 layers36 × 100 mm

Eleph
FeruzTopalov/eleph
GPS-based local relative navigation system for group of up to 6 members
56 parts24GPL-3.0
Questions
How big is the STM32-Pill PCB?
It measures 51.7 × 27.8 mm and has 6 copper layers, 1.6 mm thick.
What parts does the STM32-Pill use?
51 parts, built around the STM32WB55CCU6, 2450LP14A100T, TPS73633DBV and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the STM32-Pill KiCad files?
From the HasanTheSyrian/stm32-bluetooth-pill repository on GitHub, at the commit this page was made from: the board is STM32-Pill.kicad_pcb and its schematic STM32-Pill.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the STM32-Pill design in my own project?
Its repository states no licence, so its author keeps all rights: ask HasanTheSyrian before reusing the design.