
Amp ctrl
stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research

Hardware related to open-source shim amplifier development for MRI research
Serial interface is an open-source printed circuit board by stockmann-lab, from the stockmann-lab/shim_amp_hardware_linear repository on GitHub. It is a 2-layer board of 58 × 36.5 mm with 22 parts on 33 nets, routed with 87 tracks and 5 vias.
It is built around the UM232H-B, AFBR-1624Z and AFBR-2624Z, with the 74LVC1G14Z among its other parts. Its parts include 5 capacitors, 5 resistors, 3 ICs, 2 transistors and 2 connectors. It belongs with the interfaces and adapters and audio and music boards of this library.
This repo contains files related to the MGH "Revision D" linear amplifier development (and associated projects). The shim amplifiers are designed to drive stable currents (up to 4A/channel or more if channels are ganged together in parallel) in shim coils and other inductive loads used for MRI research experiments. The amplifiers are designed to operate inside the MRI shielded room without causing image degradation due to RF interference.
Content will include design files and bills of materials for both the Printed Circuit Boards (power board, control board, and power distribution board) as well as the mechanical enclosure.
The software and firmware for controlling the shim amplifiers via a Snickerdoodle device can be built from https://github.com/LincolnCB/rev_d_shim using the https://github.com/LincolnCB/zynq_toolbox build environment repo.
More details forthcoming.
This project builds upon previous work done at MIT-MGH on a Class-AB linear shim amplifier that uses OPA549 op amps in a push-pull configuration. This previous "Revision C" shim amplifier design is available at:
https://rflab.martinos.org/index.php?title=Current_driver:Current_driver
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | #4 / M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 4 | 1uF 16V X7R | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4 |
| 2 | 1 | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | 74LVC1G14 | Package_TO_SOT_SMD:SOT-23-5 | U3, U4 |
| 2 | DMG2305UX or similar | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | 100K | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 100nF 50V X7R | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 3.3K | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | AFBR-1624Z | shim:AFBR-xx2xZ | J1 |
| 1 | AFBR-2624Z | shim:AFBR-xx2xZ | J2 |
| 1 | Green | shim:LED_0805_2012Metric | D1 |
| 1 | UM232H | shim:FTDI_UM232H | U1 |

stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research

stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research

stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research

stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research

stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research

stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research

stockmann-lab/shim_amp_hardware_linear
Hardware related to open-source shim amplifier development for MRI research



colinoflynn/phase-modulation-sca
Resources to demonstrate phase modulation leakage including over JTAG



RadioThermal/RadioThermal_Soldering_OSHW
Open Source Hardware 470KHz Induction Soldering Iron


It measures 58 × 36.5 mm and has 2 copper layers, 1.6 mm thick.
22 parts, built around the UM232H-B, AFBR-1624Z, AFBR-2624Z and 74LVC1G14Z. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the stockmann-lab/shim_amp_hardware_linear repository on GitHub, at the commit this page was made from: the board is pcbs/serial interface/serial_interface.kicad_pcb and its schematic pcbs/amp ctrl/amp ctrl.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask stockmann-lab before reusing the design.