
Stylish Belt Synth - Left
softegg/Stylish-Trucker-Belt-Synthesizer
A stylus-based music synthesizer you can wear as a belt!

A stylus-based music synthesizer you can wear as a belt!
Stylish Belt Synth - Full is an open-source printed circuit board by softegg, from the softegg/Stylish-Trucker-Belt-Synthesizer repository on GitHub. It is a 2-layer board of 177.8 × 264.8 mm with 75 parts on 71 nets, routed with 1,361 tracks and 86 vias.
It is built around the WS2812B. Its parts include 7 connectors, 4 capacitors, 4 resistors, 4 diodes and 2 ICs. It belongs with the audio and music boards and the STM32 boards of this library.
A stylus-based music synthesizer you can wear as a belt!
Conceived as a piece of premium swag for the MAGwest convention, "Stylish!" investigates how cheaply one can make a real, useful monophonic, digital (virtual analog) music synthesizer! Borrowing the stylus-based keyboard from the venerable Stylophone, and adding complete synthesis features like multiple oscillators, filters, envelopes, vibrato, etc. that are fully adjustable so that you can make your own sounds! It may even end up with a step sequencer and drum loop! Let's bring real music synthesis to the masses, stylishly!
Project is based around the "Blue Pill" STM32F103C8T6 microcontroller board that can be obtained from AliExpress for less than $2.
Code is written using Arduino IDE and STM32Duino.
Audio output is via PWM (10k resistor + 1uF capacitor) using the Mozzi library. CC4.0 Share Alike Non-commercial license applies.
LEDs are WS2812B, and the project PCB includes a header to use a standard 16 LED ring.
Amplifier is XH-M125 based on the XPT8871, which you an also buy cheaply from AliExpress. Headers are included to simply mount this board on the unit if you don't want to solder all of those parts.
Speaker is 40-50mm 0.5W 8 Ohm

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 104 | Capacitors_SMD:C_0805_HandSoldering | CL0, CL1, CL2, CL3, CL4, CL5, CL6, CL7, CL8, CL9, CL10, CL11, CL12, CL13, CL14, CL15 |
| 16 | WS2812B | WS2812B:WS2812B | RGB0, RGB1, RGB2, RGB3, RGB4, RGB5, RGB6, RGB7, RGB8, RGB9, RGB10, RGB11, RGB12, RGB13, RGB14, RGB15 |
| 2 | + | SoftEggKiCAD:AA_Battery_+_Terminal | BTP2, BTP4 |
| 2 | - | SoftEggKiCAD:AA_Battery_-_Terminal | BTN1, BTN3 |
| 2 | 1N4148 | SoftEggKiCAD:D_DO-35_SOD27_P7.62mm_Horizontal+SMD | D1, D2 |
| 2 | 1N5822 | SoftEggKiCAD:D_DO-35_SOD27_P7.62mm_Horizontal+SMD | D3, D4 |
| 2 | Battery | SoftEggKiCAD:BatteryHolder_Keystone_2462_2xAA_MOD | BT12H1, BT34H1 |
| 2 | ~ | Connect:1pin | , |
| 2 | ~ | SoftEggKiCAD:AA_Battery_Dual_Terminal | BT12, BT34 |
| 1 | 0.39μF | SoftEggKiCAD:C_Disc_D5.0mm_W2.5mm_P5.00mm+SMD | CA4 |
| 1 | 1000μF | Capacitors_ThroughHole:CP_Radial_D10.0mm_P5.00mm | C2 |
| 1 | 100Ω | SoftEggKiCAD:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal+SMD804 | RA1 |
| 1 | 1μF | SoftEggKiCAD:C_Disc_D5.0mm_W2.5mm_P5.00mm+SMD | CA2 |
| 1 | 1μF | Capacitors_SMD:C_0805_HandSoldering | CA3 |
| 1 | 220nF | SoftEggKiCAD:C_Disc_D5.0mm_W2.5mm_P5.00mm+SMD | C1 |
| 1 | 220μF | Capacitors_ThroughHole:CP_Radial_Tantal_D4.5mm_P2.50mm | CA1 |
| 1 | 22µF | SoftEggKiCAD:C_Disc_D5.0mm_W2.5mm_P5.00mm+SMD | CL16 |
| 1 | 3.3kΩ | SoftEggKiCAD:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal+SMD804 | R2 |
| 1 | 30Ω | SoftEggKiCAD:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal+SMD804 | R3 |
| 1 | 330Ω | SoftEggKiCAD:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal+SMD804 | R1 |
| 1 | 33kΩ | SoftEggKiCAD:R_Axial_DIN0204_L3.6mm_D1.6mm_P5mm_Horizontal+SMD804 | R4 |
| 1 | 4.7nF | SoftEggKiCAD:C_Disc_D5.0mm_W2.5mm_P5.00mm+SMD | C4 |
| 1 | 470μF | Capacitors_ThroughHole:CP_Radial_D10.0mm_P5.00mm | C3 |
| 1 | Headphone | Connectors:Stereo_Jack_3.5mm_Switch_Ledino_KB3SPRS | J1 |
| 1 | LOGO | SoftEggKiCAD:SOFTEGG_LOGO2 | ~ |
| 1 | MODE | SoftEggKiCAD:LargeRoundTouchPad | J29 |
| 1 | PARAM SELECT | SoftEggKiCAD:LargeRoundTouchPad | J27 |
| 1 | PATCH SELECT | SoftEggKiCAD:LargeRoundTouchPad | J28 |
| 1 | SPEAKER | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | LS1 |
| 1 | STYLUS | SoftEggKiCAD:LargeRoundTouchPad | J30 |
| 1 | Stylus | Connectors:1pin | Stylus |
| 1 | StylusKeyboardA | SoftEggKiCAD:MAGWestSynthContactKeybed | KB1 |
| 1 | USB_B | Connectors:USB_B | J0 |
| 1 | Volume | SoftEggKiCAD:Wheel_Pot_W_Switch_RV12_B103_FUSTAR | RV1 |
| 1 | WRITE PATCH | SoftEggKiCAD:LargeRoundTouchPad | J26 |
| 1 | XPT8871 | SoftEggKiCAD:SOIC-8-N-TP | U2 |
| 1 | stm32f103c8t6-module-china | SoftEggKiCAD:stm32f103c8t6-module-china-smd | U1 |
| 1 | ~ | Connectors:1pin | ~ |

softegg/Stylish-Trucker-Belt-Synthesizer
A stylus-based music synthesizer you can wear as a belt!

softegg/Stylish-Trucker-Belt-Synthesizer
A stylus-based music synthesizer you can wear as a belt!

softegg/Stylish-Trucker-Belt-Synthesizer
A stylus-based music synthesizer you can wear as a belt!

softegg/Stylish-Trucker-Belt-Synthesizer
A stylus-based music synthesizer you can wear as a belt!

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

FrameworkComputer/ExpansionCards
Reference designs and documentation to create Expansion Cards for the Framework Laptop



PrintersForAnts/Micron
If you want to purchase full kits there are 3 available (Kits are slowly updating to R1 hardware just make sure to double check the included hardware in your kit and if you have any questions reach out in the discord)



It measures 177.8 × 264.8 mm and has 2 copper layers, 1.6 mm thick.
75 parts, built around the WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the softegg/Stylish-Trucker-Belt-Synthesizer repository on GitHub, at the commit this page was made from: the board is MAG Synth/Stylish-Belt-Synth - Full.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask softegg before reusing the design.